SmallRig 3495LEQI Wave Wireless Lavalier Microphone User Manual

SmallRig 3495LEQI Wave Wireless Lavalier Microphone User Manual

List of Items

• Transmitter (TX)

• Receiver (RX) x1

• USB-C Charging Cable x1

• User Manual x1

• Charging Case ×1

• Furry Windscreen x1

Product Details

**Transmitter (TX):

**

1. 1 On/Off Button
2. + Microphone Gain Adjustment Button
3. LED Indicator Light
4. Charging Contact
5. Collar Clip
6. Microphone Pickup Hole
7. 3.5mm Headphone Port

**Receiver(RX):

**

1. Pairing Button
2. USB-C Interface
3. Led Indicator Light

Charging Case:

1. Opening Button
2. Transmitter (TX)
3. Receiver (RX)
4. Furry Windscreen
5. Led Indicator Light
6. USB-C Charging Port

Product Operations

Pairing and Use:

The microphone (TX) and receiver (RX) have been paired before leaving the factory. You can insert receiver (RX) into the mobile phone and other devices after taking it out from the charging case. Then microphone (TX) will automatically start and carry out pairing connection

Use: Take out microphone (TX) and clamp it at the collar. Take out the receiver and insert it into USB-C port of the mobile phone. Then you can use it.

Manual Pairing: If the factory pairing is not successful, you can pair them by yourself, Press the power button and sound volume + button of microphone (TX) for 2 seconds. Then the white light flashes quickly. Press the pairing button of receiver (RX) for 2 seconds. (Pairing: quick flash of white light; Connected: white light normally on)

Start: If you power off the microphone accidentally, you can long press the on/off button of microphone (TX) for 2 seconds to start it or re-connect it.

Automatic Re-connection: The microphone has been paired successfully and has memory function, When you use it next time, microphone (TX) and receiver (RX) can be reconnected automatically.

• Automatic re-connection condition will occur when the connection scope of microphone and the receiver is exceeded..
• Re-connection: slow flash of white light; Connected: white light normally on.
• If the microphone (TX) and the receiver (RX) return to connection distance scope within 5 minutes, automatic reconnection can be successful. Otherwise, the microphone (TX) and the receiver (RX) will be powered off automatically

Automatic Power-off:

• If pairing is not successful within 5 minutes under pairing status, the microphone (TX) will automatically enter power-off status.
• If re-connection is not successful within 5 minutes under automatic re-connection status, the microphone (TX) will automatically enter power-off status

Mute :

• The On/Off button of microphone (TX) is provided with mute function, You can short press the On/Off button to enter mute function;
• To disenable the mute function, you can short press the On/Off button again.

Charging:

• If one white LED light is normally on, it indicates 25% electric quantity. If two white LED lights are normally on, it indicates 50% electric quantity. If three white LED lights are normally on, it indicates 75% electric quantity. If four white LED lights are normally on, it indicates 100% electric quantity.
• When you put the microphone (TX) in the charging case and the red light is normally on, it indicates that it is being charged. If the red light is off, it indicates that the charging is completed. (Tips: RX has no battery and LED light display)
• The charging case should be charged with USB-C, During charging, if the white light is normally on, it indicates that current electric quantity has been reached. If the white light flashes, it indicates that charging is under progress to reach corresponding electric quantity. If 4 lights are normally on, it indicates that the charging is completed, If the microphone is not used, it is recommend- ed to close to charging case to save electricity.

Gain Adjustment:
To increase or decrease the gain via clicking “+” or “-” buttons of TX. 4.
Noise Reduction : Double-click “Volume +” or “Volume -” to cycle the noise reduction modes to suit the ambient noise level (Level 1: red and white flashing together 1 time, Level 2: red and white flashing together 2 times; Level 3: red and white flashing together 3 times, Off: red and white flashing together 4 times).

Product Parameters

combination with the charging base
Port Of Charging Case| USB-C 5V= 1A
Battery Specification| TX: 130mAh 3.7V 0.481Wh
Charging Case: 730mAh 3.7V 2.701 Wh
Charging Time| TX: 1 hour
Charging Case: 2 hours.1

FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. (1) This device may not cause harmful interference, and
   (2) this device must accept any interference received, including interference that may cause undesired operation, This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  To maintain compliance with FCC’s RF Exposure guidelines, the 20cm is the minimum distance that has to be maintained between your body and the device. FCC ID: 2AZW-3495LEQI

Service Warranty

Please keep your original purchase receipt and warranty card, including your purchase date, product serial number, etc., which are required for the warranty service.

After-sale Warranty Terms

1. 7 Days DOA Return Policy: Within 7 days from the package receipt date, return or replacement can be done if the item received is malfunctioning or physically damaged (non-artificial damage), return shipping cost will be on Small Rig’s charge.
2. 1-Year Warranty: Within 1-year from the package receipt date, the defective product (non-artificial damage) is eligible to get repair / replacement for free. The defective product (artificial damage) will be charged for repairing / replacement based on the damage level.

This Warranty Does Not Cover

1. Defect caused by users’ violation of the “Warnings” and “Intended Use”.
2. The product identification or SN label is removed or defaced in any way.
3. The product is serviced or repaired by anyone other than our company or the service agency authorized by our company.

Guarantee Card

Serial No.|
---|---
Item Name|
Purchase Date|
User Name|
Mobile|
Address|
Receipt|

Hello!
Thank you for purchasing Small Rig Wave W1-C. It is a high-quality wireless microphone and designed for podcast, vlogger and live streaming requiring broadcasting quality. Wave W1-C with wireless audio transmission technology of low-latency features excellent sound quality, compact and concise design, superior surface treatment. It is suitable for smartphones and computers. It supports plug and play in mobile phones/Mac/PC. Therefore, Wave W1-C can satisfy your demand for real-time recording. Wave W1-C is provided with no- latency headphone output, gain adjustment, environmental noise reduction adjustment, microphone mute control functions and can bring broadcast-level sound experience for your recording and live streaming.

Warnings

• Please read this User Manual carefully.
• Please do not use the product in water.
• The product contain electronic components, do not let the product fall to the ground, be hit, or suffer a violent impact.
• Please do not use the product in a completely closed environment. It may increase the internal temperature of the product, which causes product failure, ignition, or other accident.
• Never remove the non-detachable lithium battery in the product without permission.
• When the battery of the product is not in use for a long time, please charge and discharge the battery every six months, and provide it with about 60% of the electric quantity to prolong its service life.
• Since there are some hazardous substances in the battery of the product, please do not discard it. Instead, dispose of the product that is damaged or will never be used according to the waste management measures.
• When the product is not in use, it should be stored in a dry and clean place. Avoid high temperature, high humidity, and strong magnetic field.

Please do not disassemble the product. If you have any questions,
please contact the seller to apply for after-sales service.

Made in China

Manufacturer : Shenzhen Lei Network Technology Co., Ltd.
Add: 1st Floor, Building 9, Yahoo Industrial Park, Bantian, Longing, Shenzhen, Guangdong, China.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>