MOUNTUP MU6005 Height Adjustable Single Monitor Desk Mount Instruction Manual

June 15, 2024
MOUNTUP

MOUNTUP MU6005 Height Adjustable Single Monitor Desk Mount

WARNING!

If you have any confusion or are not quite sure about the installation, please do not hesitate to ask for our help. Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use. The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS ****

ASSEMBLY STEPS

STEP 1: Clamp Installation OR Grommet Base Installation

  • OPTION A: Clamp Installation
    Install the Clamp (C) to the Pole (D) using 3pcs Bolt(G). Tighten using 4mm Allen key (L). Secure stand to the desktop by tightening the plastic knob or by using 6mm Allen key (M).MOUNTUP-MU6005-Height-Adjustable-Single-Monitor-
Desk-Mount-fig-2

  • OPTION B: Grommet Base Installation
    If existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount. Loosen the screw, separate the clamp (C) into two parts.
    Install the Base Plate (J) to the Pole(D)using 1pc of Bolt (G). Install the pole (D) on the desktop using the support plate (I) and the bolt separated from clamp(C). Secure stand to desktop by tightening the plastic knob or by using 6mm Allen key (M).

STEP 2 : Arm Installation

Install the wire clip(F) and swivel arm(A and B) to the pole(D). Fasten the bolt with supplied 6mm Allen key (M) and 3mm Allen key (K)MOUNTUP-MU6005
-Height-Adjustable-Single-Monitor-Desk-Mount-fig-5

STEP 3 : Attach Monitor

  • OPTION A: Flat Back Monitor
    Attach the VESA plate (E) to the back of monitor and secure it by using a 6 mm Allen Key (M) to tighten screws (M-A).

  • OPTION B: Curved Back Monitor
    Attach the VESA plate (E) to the back of monitor and secure it by using a 6 mm Allen Key (M) to tighten screws (M-B) along with spacers (M-C).

MOUNTUP-MU6005-Height-Adjustable-Single-Monitor-Desk-Mount-
fig-6

Be sure NOT TO tighten the screws too tightly, or may cause damage to your monitor.

STEP 4: Hang Monitor

Slide the monitor onto the head of swivel arm, install the security bolt (H). Make sure the security bolt is installed before you rotate the monitor .MOUNTUP-MU6005-Height-Adjustable-Single-Monitor-Desk-Mount-
fig-7

Problem:

  • If the monitor face down

Solution:

  1. Loosen the tilting bolt.
  2. Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
  3. Retighten the tilting bolt to fix the intended angle.

STEP 5: Adjust Tension

For intended functioning of the mount, you may need to adjust the tension of Upper Arm (B) in accordance with your monitor weight by 6 mm Allen Key (M ).MOUNTUP-MU6005-Height-Adjustable-Single-Monitor-Desk-Mount-
fig-8

STEP 6: Cable Management

Remove Cable Cover

  • For lower arm: Remove bottom plastic cover from lower arm as shown in the diagram.

Attach Cable Cover

  • For lower arm: Run cables through the cable cover, then slide the cover down to reattach the cable cover;
  • For upper arm: Run cables through the cable cover (B-B), then slightly press the tabs on the inside of the cable cover inward and insert the cable cover to upper arm.MOUNTUP-MU6005-Height-Adjustable-Single-Monitor-Desk-Mount-fig-9

Adjust as Desired

Adjust monitor position and rotation. Allen Key can be stored in Wire clip (F) for next time using.

  • Tilt
  • Swivel
  • Rotation
  • HeightMOUNTUP-MU6005-Height-Adjustable-Single-Monitor-Desk-Mount-fig-10

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.

Product Dimensions

CAUTION AND MAINTENANCE

  • Never allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals