KuWFi CPE400 Outdoor Wireless Bridge Installation Guide
- June 15, 2024
- KuWFi
Table of Contents
- KuWFi CPE400 Outdoor Wireless Bridge
- Product Usage Instructions
- List of Packaging Accessories
- Product Appearance and Interface
- Video Transmission Introduction
- Outdoor CPE Specification
- Digital Display Setting
- WeBUI Manage Pages
- Field Application
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
KuWFi CPE400 Outdoor Wireless Bridge
Specifications
- DRAM: DDR2 64MByte
- FLASH: 16MByte
- Wired Interface: 10/100Mbps LAN*3
- DC output : 12V out *2
- Transfer method: Direct Sequence Spread Spectrum (DSSS)
- Modulation: OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK
- Network Standard : IEEE802.11n, IEEE802.11a
- Power scheme : POE 48V 0.5A
- Operating temperature : -30 ~ 65
Product Usage Instructions
List of Packaging Accessories
The product box includes the following items
- 48V POE Adapter – 2 pieces
- Outdoor CPE – 2 pieces
- 12V DC Cable – 4 pieces
- RJ45 Cable (1M) – 2 pieces
- Lashing Rope – 4 pieces
- User Manual – 1 piece
Product Appearance and Interface
The product has a compact and sleek design. It features multiple interfaces
for connectivity.
Video Transmission Introduction
The Outdoor CPE functions as a long-distance wireless transmission
equipment. It supports point-to-point and point-to-multipoint modes. The
transmission distance can reach up to 3km (Barrier-Free). It also supports WDS
networking mode and video network dual compatibility. The transmitter and
receiver can be set through dialing, and the IP settings can be modified using
a PC.
Outdoor CPE Function
The Outdoor CPE serves as a long-distance 5.8G wireless transmission
equipment. It supports point-to-point and point-to-multipoint modes. The
transmission distance can reach up to 3km (Barrier-Free). It also supports WDS
networking mode and video network dual compatibility. The transmitter and
receiver can be set through dialing, and the IP settings can be modified using
a PC.
Digital Display Setting
The digital display bridge can be easily connected by dialing. Set Bridge 1
and Bridge 2 to AP and STA mode, then set the two bridges to the same number
(1, 2, 3, … F) using the shift button. This will automatically connect the two
bridges without requiring IP setting on a computer. The signal light will
indicate successful pairing. The dialing settings are suitable for both point-
to-point and point-to-multipoint connections.
WeBUI Manage Pages
To connect the CPE, use an RJ45 cable to connect it to your LAN port.
Follow these steps to configure your PC IP as 192.168.0.xxx
- Find the network connection you are using and right-click on Properties.
- Double-click the IPV4 setting and select the IP address below. Enter the IP and confirm.
- Configure your PC IP as 192.168.0.xxx (xxx is a figure between 2-254). Note that the set PC IP cannot be the same as the IP of the CPE.
The default IP for accessing the CPE WebUI is 192.168.0.20. The default username and password are admin/admin.
Wireless Basic Configuration
Scan the SSID of the AP device using a STA device. This is also a method of
manual pairing. If the pairing succeeds, it will show “Pairing succeeded.” If
it shows “No information available,” it means the pairing has failed.
Wireless Advanced Configuration
In this section, you can configure the operating frequency mode, channel,
width, transmit power, and distance optimization for wireless transmission.
There is also an option to change the router password for accessing the
device.
Field Application
Field application details are not provided in the user manual.
FAQ
-
Q: What should I do if the pairing fails?
A: If the pairing fails, please ensure that the SSID of the AP device is correctly scanned by the STA device. Check that both devices are properly configured and within range of each other. You may also try resetting the devices and repeating the pairing process. -
Q: Can I use the Outdoor CPE for both point-to-point and point-to-multipoint connections?
A: Yes, the Outdoor CPE supports both point-to-point and point-to-multipoint connections. You can easily configure it for your desired network setup.
Note: Thank you for order and using our product, please read the manual carefully before use. If there are any problems during the use, please contact us in time
List of Packaging Accessories
What is in the box
- 48V POE Adapter *2
- Outdoor CPE *2
- 12V DC Cable *4
- RJ45 Cable(1M) *2
- Lashing Rope *4
- User Manual *1
Product Appearance and Interface
Video Transmission Introduction
- CPE is widely used in highways, reservoir river monitoring, elevator monitoring systems, site crane monitoring systems, port terminal monitoring systems, marine aquaculture monitoring systems and So on.
- CPE Video Bridge Transmission usually consists of two devices in AP and Station mode respectively. At the Station-side (Receiving side) CPE connects with IP Camera, at the AP side (Transmitting side) CPE connects with a video recorder.
- The AP can be receiving wireless data transmitted from multiple Station, and it is easy and convenient for centralized management of the remote equipment.
Outdoor CPE Function
- Long-distance 5.8G wireless transmission equipment
- Support point-to-point, point-to-multipoint mode
- Transmission distance up to 3km(Barrier-Free)
- WDS networking mode, video network dual compatible
- Dialing to set the transmitter and receiver, and also support the PC to modify the IP settings
Outdoor CPE Specification
- DRAM : DDR2 64MByte
- FLASH : 16MByte
- Wired Interface : 10/100Mbps LAN*3
- DC output : 12V out *2
- Transfer method: Direct Sequence Spread Spectrum (DSSS)
- Modulation: OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK
- Network Standard: IEEE802. 11n,IEEE802.11a
- Power scheme: POE 48V 0.5A
- Operating temperature: -30℃ ~ 65℃
Digital Display Setting
The digital display bridge is simply connected by dialing. After setting
Bridge 1 and Bridge 2 to AP and STA mode, set the two bridges to the same
number (1,2,3, … F) through the “shift” button, then the two bridges can be
automatically connected without using a computer for IP setting (Signal light
on=pairing succeeded). The dialing settings are connected using a
point-to-point bridge, which is also suitable for point-to-multipoint
connections
WeBUI Manage Pages
Connect the CPE by LAN port (Use RJ45 cable)
How to Configure Your PC IP
As 192.168.0.xxx:
- Find the network connection you are using and right click on Properties.
- Double- click the IPV4 setting, select the IP address below, enter the IP and confirm.
- Configure your PC IP as 192.168.0.xxx (xxx is a figure 2-254), note that the set PC IP cannot be the same as the IP of the CPE
Login WebUI
CPE Default IP(192.168.0.20) User Name and Password: admin/admin
CPE Advanced Settings
Since the Bridge devices are mainly used for long-range signal bridge and
repeating,and to avoid IP address confliction when the CPE is connected with
another router device,our bridge products disable the DHCP function(automatic
IP address assignment)by default
How to pair manually
- STA: Means Slave AP
- AP: Means Master AP
When Toggle switch button on STA side, mean this outdoor CPE is a slave AP; When Toggle switch button on AP side, mean this outdoor CPE is a master AP
- Power on the Master AP and Slave AP
- Push the Toggle switch button to AP side on Master AP, Slave AP on STA side
- Short press the reset button on master AP and Slave AP
- Wait a while the device will be automatically paired
Wireless Basic Configuration
Here, Use the STA device to scan the SSID of AP device, which is also a method
of manual pairing
Pairing succeeded (If show “No information
available”,means pairing failed)
Wireless Advanced Configuration
Operating frequency（Mode/Channel/Width）/ Transmit Power/ Distance optimization
Wireless Mode Switch
- High speed mode has high data transmission speed and is used for short distance high-speed transmission, but its stability is poor. It is recommended to use stable mode.
- Router Password: Changes the administrator password for accessing the device
Field Application
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>