KuWFi CPE550-2 Outdoor Wireless Ethernet Bridge Installation Guide

June 10, 2024
KuWFi

KuWFi-LOGO

KuWFi CPE550-2 Outdoor Wireless Ethernet Bridge

KuWFi-CPE550-2-Outdoor-Wireless-Ethernet-Bridge-
PRODUCT

Note:
Thank you for ordering and using our product, please read the manual carefully before use. If there are any problems during the use, please contact us in time

Get Started to Know Your Wireless Bridge

KuWFi-CPE550-2-Outdoor-
Wireless-Ethernet-Bridge-FIG- \(1\)

CPE Bridge For Video Transmission Introdu

  • CPE is widely used in highways, reservoir river monitoring, elevator monitoring systems, site crane monitoring systems, port terminal monitoring systems, marine aquaculture monitoring systems, and So on.
  • CPE Video Bridge Transmission usually consists of two devices in AP and Client mode respectively. At the Client-side (Receiving side) CPE connects with IP Camera, at the AP side (Transmitting side) CPE connects with a video recorder. The AP can be receiving wireless data transmitted from multiple Clients, and it is easy and convenient for centralized management of the remote equipment.

Outdoor CPE Function

  1. Long-distance 5.8G wireless transmission equipment
  2. Support point-to-point, point-to-multipoint mode
  3. Transmission distance up to 5km(Barrier-Free)
  4. WDS networking mode, video network dual compatible.
  5. Dialing to set the transmitter and receiver, and also support the PC to modify the IP settings.

Outdoor CPE Specification

  • DRAM : DDR2 64MByte
  • FLASH : 16MByte
  • Wired Interface : 10/100Mbps LAN*2
  • Transfer method: Direct Sequence Spread Spectrum (DSSS)
  • Modulation: OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK
  • Network Standard : IEEE802. 11n,IEEE802.11a ,IEEE802.3u
  • Power scheme : POE 24V 1A
  • Encryption: WEP encryption 64/128bits, WPA, WPA2, 802.1x
  • Operating temperature: -30℃ ~ 65℃

Digital Display Wireless Bridge Set Up

The digital display bridge is simply connected by dialing. After setting Bridge 1 and Bridge 2 to A and B mode, set the two bridges to the same number (1,2,3, … F) through the “reset” button, then the two bridges can be automatically connected without using a computer for IP setting. The dialing settings are connected using a point-to-point bridge, which is also suitable for point-to-multipoint connections.KuWFi-CPE550-2-Outdoor-Wireless-
Ethernet-Bridge-FIG- \(2\)

INSTRUCTION

  • Before connecting the power supply, move bridge 1 to the A end through the A-B button, and bridge 2 moves to the B end through the A-B button, the A end represents the receiving mode, and the B end represents the transmitting mode; The bridge 1 and the bridge 2 are respectively set after A and B. Connect the bridge to the power supply, the digital display shows“L” and flashes, and the“L” disappears to indicate that the configuration connection is successful. At the same time the WLAN signal light is on and flashing.
  • The reset button to set the led digital display, click once the startup configuration status is, continue to click, the number will increase, can be continuously increased.
    Assume that a pair of bridges with a number of 3 is configured After bridge 1 set to 3, after the bridge 2 set to 3, first the LED light will flash, then “L” flashes to indicate the application is being configured, please be patient, When “L” flashes, it will become the number “3”, and the number “3” will continue to flash until the bridge 1, bridge 2 is connected after the success, the LED display“3”is always on, not flashing, indicating that the bridge 1 and bridge 2 has been successfully networked.

LED Number & IP ChartKuWFi-CPE550-2-Outdoor-Wireless-Ethernet-Bridge-FIG-
13

CPE Advanced Settings, Suitable for Point-to-multipoint

Since the Bridge devices are mainly used for long-range signal bridge and repeating, and to avoid IP address confliction when the CPE is connected with another router device, our bridge products disable the DHCP function (automatic IP address assignment) by default, you need configure the CPE at the first time to use it properly.
Pls configure your PC IP as 192.168.255.xxx (XXX is a figure 2-254), and then pls connect the CPE as the diagram below. Then power on CPE, input 192.168.255.100 at the IE bar, then input user name and password at the user interface to enter into the configuration page.
CPE Default IP : 192. 168.255.100
Notes : The IP address of WebUI changes with the LED number (Reference LED Number & IP Chart Setting IP) CPE Default User Name and Password: admin/admin

How to Configure Your PC IP As 192.168.255.xxx:

  • Find the network icon in the lower right corner and click Open Network and Internet Settings.
  • Select Ethernet and Click the Change Adapter Option.
  • Find the network connection you are using and right-click on Properties.
  • Double-click the IPV4 setting, select the IP address below, enter the IP, and confirm.
  • Configure your PC IP as 192.168.255.xxx (xxx is a figure 2-254), note that the set PC IP cannot be the same as the IP of the CPE.

KuWFi-CPE550-2-Outdoor-Wireless-Ethernet-Bridge-FIG-
\(5\) KuWFi-CPE550-2-Outdoor-Wireless-
Ethernet-Bridge-FIG- \(6\)

Bridge Configuration

Note : Before configuring the Bridge IP, AP Configuration, and Client Configuration, make sure that the PC and CPE are properly connected and that the PC IP is configured

  1. Computer Setup Debug Connection DiagramKuWFi-CPE550-2-Outdoor-Wireless-Ethernet-Bridge-FIG- \(7\)
  2. Wireless Transmission Mode ( Transmission Point) Select “A(Master)” under the “Mode”, then select Matching ID ( Such as “136” ). See the figure below:KuWFi-CPE550-2-Outdoor-Wireless-Ethernet-Bridge-FIG- \(8\)
  3. Wireless Receiver Mode (Receiving Point) Select “B(Slave)” under the “Mode”, then select Matching ID ( Such as “136” ). See the figure below:KuWFi-CPE550-2-Outdoor-Wireless-Ethernet-Bridge-FIG- \(9\)

Field Applications

WiFi coverageKuWFi-CPE550-2-Outdoor-Wireless-Ethernet-Bridge-FIG-
\(10\)

Point-to-Multi ConnectionKuWFi-CPE550-2-Outdoor-Wireless-Ethernet-Bridge-
FIG- \(11\) Multi-to-Multi Connection

KuWFi-CPE550-2-Outdoor-Wireless-Ethernet-Bridge-FIG-
\(12\)

Documents / Resources

| KuWFi CPE550-2 Outdoor Wireless Ethernet Bridge [pdf] Installation Guide
CPE550-2, B0BD331W8X, B07Y3D6DHD, B086964DLZ, CPE550-2 Outdoor Wireless Ethernet Bridge, Outdoor Wireless Ethernet Bridge, Wireless Ethernet Bridge, Ethernet Bridge, Bridge
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals