ergotron MXV Desk Single Monitor Arm Instruction Manual
- June 15, 2024
- ERGOTRON
Table of Contents
**ergotron MXV Desk Single Monitor Arm Instruction Manual
**
For the latest User Installation Guide please visit : www.ergotron.com
Safety
Hazard Symbols Review
These symbols alert users of a safety condition that demands attention. All
users should be able to recognize and understand the significance of the
following Safety Hazards if encountered on the product or within the
documentation. Children who are not able to recognize and respond
appropriately to Safety Alerts should not use this product without adult
supervision
| Symbol | Signal Word | Level of Hazard |
|---|---|---|
| NOTE | A NOTE indicates important information that helps you make |
better use of this product
| CAUTION| A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem
| WARNING| A WARNING indicates either potential for property damage, personal injury, or death.
| ELECTRICAL| An Electrical indicates an impending electrical hazard which, if not avoided, may result in personal injury, fi re and/or death..
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
Warning: Because mounting surface materials can vary widely, it is
imperative that you make sure mounting surface is strong enough to handle
mounted product and equipment.
Caution:
To avoid the potential to pinch cables it is important to follow the cable
routing instructions in this manual. Failure to follow these instructions may
result in equipment damage or personal injury.
CAUTION: DO NOT rotate monitor past rear edge of desk. Doing so will create an unstable situation and may cause equipment damage or personal injury.
Features & Specifications
7lbs (5.2 kg) – 2O lbs. (9.1 kg)
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
Components
Tools Needed
Assembly
ATTACH DISPLAY
NOTE: VESA plate will only accept 75mm or 100mm VESA pattern.
WARNING! Stored Energy Hazard: The Riser mechanism is under tension and will move up rapidly, on its own, as soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the Riser has been moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or equipment damage!
NOTE: Leave enough slack in cable to allow full range of motion.
Caution: To avoid the potential to pinch cables it is important to follow
the cable routing instructions in this manual.
Failure to follow these instructions may result in equipment damage or
personal injury.
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before a5empting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
a. Lift – Up and down
b. Tilt – Forward and Backward
a. Lift – Up and down
Increase Lift Strength
If the mounted weight is too heavy or this product does not stay up when
raised, then you’ll need to increase Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or this product does not stay down when
lowered, then you’ll need to decrease Lift Strength:
CAUTION: DO NOT overtighten fasteners. Overtightening may cause damage to your equipment.
b. Tilt – Forward and Backward
Increase Friction
If this product moves too easily, then you’ll need to increase friction:
Decrease Friction
If this product is too difficult to move, then you’ll need to decrease friction:
Learn more about ergonomic computer use at: www.ergotron.com/ergonomics
For Warranty visit:
www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit:
http://contact.ergotron.com
NOTE: When contacting customer service, reference the serial number.
www.ergotron.com | USA: 1-800-888-8458 | Europe: +31 (0)33-45 45 600 | China: 400-120-3051 | Japan: japansupport@ergotron.com
© 2016 Ergotron, Inc. All rights reserved.
While Ergotron, Inc. makes every effort to provide accurate and complete information on the installation and use of its products, it will not be held liable for any editorial errors or omissions (including those made in the process of translation from English to another language), or for incidental, special or consequential damages of any nature resulting from furnishing this instruction and performance of equipment in connection with this instruction. Ergotron, Inc. reserves the right to make changes in the product design and/or product documentation without notification to its users. For the most current product information, or to know if this document is available in languages other than those herein, please contact Ergotron. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written consent of Ergotron, Inc., 1181 Trapp Road, Eagan, Minnesota, 55121, USA Patents Pending and Patented U.S. & Foreign. Ergotron is a registered trademark of Ergotron, Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>