INGO MAURER Lucellino Doppio LED Instructions
- June 6, 2024
- INGO MAURER
Table of Contents
MAURER Lucellino Doppio LED
Instructions
Instructions for assembly
Please read these instructions carefully before going any further, and keep
them in a safe place for future reference
The lamp assembly and all electrical work must be carried out by a
professional electrician.
Caution: Lucellino is not suitable for use in damp areas or outdoor
areas. The wings can be impregnated with ordinary hairspray or hair lacquer.
Important: Lucellino nt LED requires a 12-volt power supply. Never
connect the LED bulb directly to the mains supply (230/125 volts)!
Caution: Switch off or remove the fuse for the mains supply to the wall
or ceiling outlet before beginning the assembly.
Preparations for assembly
Undo the Allen screw on the brass bolt (1), pull out the brass wire (2) and
remove the white cover (3). Undo the two screws (4) on the lid and open the
outlet box (5). Use the box as a template to mark the two drill holes.
Caution: Take care to ascertain the exact layout of the wiring in the
wall or ceiling, so as to avoid drilling into a power cable.
Assembly
Drill the two 6 mm-diameter holes and insert the S6 plugs. Attach the outlet
box (5) with the screws (6) provided and tighten the screws, as shown in fig.
Remove about 8 cm from the outer covering of the power cable (7) and strip 5
mm from the ends of the phase and neutral leads. Connect the phase and neutral
leads to the contacts in the terminal (8). Replace the lid of the wall box,
fasten the two screws (4) and fit the white cover (3).
Push the brass wire (2) into the bolt (1) until it reaches the stop, and
position it as desired. Tighten the Allen screw on the brass bolt.
Inserting the bulb
Screw the LED bulb into the holder and insert the enclosed red wire (9) firmly
in the contact sleeve on the bulb (10). Adjust the red wire so that it follows
the path of the brass wire (threading it once or twice around the latter) and
insert the end firmly in the contact sleeve on the white cover (11).
Changing the bulb
Caution: Switch off or remove the fuse for the mains supply and allow the
lamp to cool down completely!
Important: Lucellino LED requires a 12-volt power supply.
Caution: The LED light bulb must not be used in any 24 volts halogen
version of Birds or Lucellino!
Before unscrewing the spent bulb, pull the red wire (9) out of the contact
sleeve (11) and unwind it from the brass wire. Then follow the procedure
described above in the section headed,, Inserting the bulb”.
Cleaning
The goose-feather wings can be cleaned carefully with a soft paintbrush. A
mild household cleaning fluid may be used for the cover and cable.
Technical specification
220-240 V~50 Hz; 110-130 V~60 Hz. The correct voltage and frequency for your
lamp are indicated on the type label.
Secondary 12 VAC. LED 1.5 W, 100 lm, 2600 K, CRI>95, E27 socket, Doppio: 2x
1.5W LED
According to the manufacturer, the LED has an average life of 15 000 hours.
Electronic transformer, dimmable (dimmer not included). It is possible to
connect a universal dimmer for LEDs (with low or adjustable minimum load).
The lamp comes with a bulb of energy class A+.
The LED bulb is manufactured exclusively for Ingo Maurer GmbH. Replacements
are only available from our webshop or authorized retailers.
A defective transformer or LED bulb must be disposed of as electronic scrap,
it must not get into domestic waste.
Any repairs that may become necessary must be carried out by a qualified
electrician. The legal and contractual warranty for defects and product
liability will be void, should the installation instructions not be duly
followed or non-original components be employed.
Ingo Maurer GmbH
Kaiserstrasse 47
D-80801 München
Tel. +49. 89. 381 606-0
Fax +49. 89. 381 606 20
info@ingo-maurer.com
www.ingo-maurer.com
Dezember 2020
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>