UeeVii CPE-820 5.8G 1Gbps WiFi Outdoor CPE Bridge User Manual

UeeVii CPE-820 5.8G 1Gbps WiFi Outdoor CPE Bridge

Model: CPE-820

Tips:
Thank you for ordering and using UeeVii CPE820 Wireless Bridge, please read the manual carefully before use. If there are any problems during the use, please contact us in time. The installation of this device requires some network knowledge. If you can’t install it, please let us know or contact a professional.

• Customer Service Email: support@ueevii.com

OVERVIEW

Introduce

UeeVii CPE820 is a long-distance 5.8G wireless transmission device. It uses wireless communication technology to transmit network data using air as a medium to perform long-distance point-to-point or point-to-multipoint inter connection. The working data link layer realizes the interconnection of local area networks. The transmission distance can reach up to 3km. CPE820 Video Bridge Transmission usually consists of two devices in AP and Client mode respectively. On the Client-side (Receiving side) CPE connects with IP Camera, at the AP side (Transmitting side) CPE connects with a video recorder. The AP can be receiving wireless data transmitted from multiple Clients, and it is easy and convenient for centralized management of the remote equipment. CPE is widely used in highways, reservoir river monitoring, elevator monitoring systems, site crane monitoring systems, port terminal monitoring systems, marine aquaculture monitoring systems, and so on. Point to point extend network WiFi range, extend the network in the house to your barn, garage, church, warehouse, and even neighbor’s house through wireless bridge signal transmission. No need to install a new modem and pay for it every month, saving you money.

Highlights

1. Transmission using 5.8Ghz wireless technology；
2. 1000Mbps RJ45 LAN port, support Gigabit；
3. Built-in 16dbi high gain WiFi antenna；
4. IEEE802.11ac IEEE802.11n,IEEE802.11a ,IEEE802.3u；
5. Transmission distance up to 3km(Barrier-Free)；
6. Master bridge supports WiFi hotspot access；
7. Dialing to set the transmitter and receiver, is easy to use；
8. WDS networking mode, video network dual compatible；
9. Support point-to-point, point-to-multipoint mode；
10. Dynamic MIMO power saving mode (DMPS) and APSD；
11. Support 24V POE power supply, easy to install and deploy；
12. Support WEB GUI access management device.

Specifications

574.2M.M4,M4,184M8.4.,3M6,M2,41,2.74MM,,2188.M9M,1,24M3.,39MM,,567M.8bMp,s65M,72.2M,

144.4M2bp9sM433M3bMp,5s7.8M,86.7M,115.6M,130M,

Transfer method| Direct Sequence Spread Spectrum(DS)
Modulation| OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK
Protocol standard| IEEE802.11ac IEEE802.11n,IEEE802.11a ,IEEE802.3u
Agreement| CNSDMISA5/CA, TCP/IP, IPX/SPX, NetBEUI,DHCP, NDIS3,NDIS4,
Frequency Range| 4900～6100MHz
Power| ≤3W, POE 24V~1A/48V~0.5A
Antenna| 16dBi,Horizontal 60°/Vertical 30°
WEP GUI| Support
Telnet| Support
Serial| Support
Safety| WEP 64/128bits,WPA,WPA2,802.1x
Temperature| -30～65℃
Box Size & Weight| 11.811.52.7 inch & 2.2 LB

Package Included

• 2 * CPE820 Gigabit Bridge
• 2 * Gigabit POE Adapter (24V)
• 2 * Cat 5e Network Cable
• 2 * Metal Hoop
• 1 * User Manual

Interface Details

Button Operation

Reset Button
Press and hold for 10S to reset the wireless bridge; in setup mode, short press once to toggle a different character to pair.

A-B Button
Pushing the button to “A” indicates that the bridge acts as the master bridge (transmitter), and pushing the button to “B” indicates that the bridge acts as the slave bridge (receiver).

LED Indicator Details

rciodngneeisctceodntnheectWeLdAsNuclicgehstsfwuillllyn, tohtebWe lLitA.N light will
LAN1/LAN2| Tothheedrwatiasec, point ni sensor to bright successful, the LED light is on,
PWR| Power indicator, the LED is on after the power is connected
Digital Tube| Dstiagtiutasl display LED display “H” indicates manual configuration
Digital Tube| Dstiagtiutasl display LED display “L” and flashing indicates settings
Digital Tube| Dcoignintaelcdtiinspglay LED flashing indicates edit the config or
Digital Tube| bDrisidpglaeys tahraetpaafiirxeeddsnuuccmebssefruilslysaonlid,aitremweoarnksinthga. t the two
Point Light| A, B status lights, lighting is B mode, no lighting is A mode.

PoE Power Supply
The CPE820 wireless bridge adopts a PoE power supply, which is easy to install and manage while saving costs.

1. According to the requirements, prepare a long enough network cable （ Recommended within 20 meters, must Cat 5e or up） to connect the wireless bridge and the PoE power supply. The PoE port of the PoE power supply is connected to the WAN port of the wireless bridge.
2. The LAN port of the PoE power supply is connected to the PC, router, and switch.

Point-to-Point Pairing Step

1. Switch one unit to A(Master Bridge) and one unit to B(Slave Bridge);
2. Connect the POE to each unit using the Ethernet cable and plug the POE in;
3. Wait for them to power up, about 2 min;
4. Use the tiny reset button to click through until you get a channel with a letter. 1,2,3,…, A,B,C,…,F, here used C;
5. Then on the other unit do the same. Both units need to be on the same channel;
6. Wait for 2-5 minutes to complete the pairing. When the number of the digital tube is solid and the signal light on the side turns on, it means the pairing is successful;
7. Finally connect other devices(Router, PC, Switch) and install them to the target location.

Point to Multipoint Pairing Step

1 master bridge with 3 slave bridges

1. Switch one unit to A(Master Bridge) and 3 units to B(Slave Bridge);
2. Connect the POE to each unit using the Ethernet cable and plug the POE in;
3. Wait for them to power up, about 2 min;
4. Use the tiny reset button to click through until you get a channel with a letter. 1,2,3,…, A,B,C,…,F, here used C;
5. Then on the other 3 unit do the same. 4 units need to be on the same channel;
6. Wait for 2-5 minutes to complete the pairing. When the number of the digital tube is solid and the signal light on the side turns on, it means their pairing is successful;
7. Finally connect other devices(Router, PC, Switch) and install them to the target location.

Installation

1. Place the CPE to the selected position and adjust the CPE front panel orientation to be approximately the same as the selected direction, then use the ties to fix the CPE, the bracket is not included in the package. Recommended UeeVii Universal Bracket (ASIN: B09NLLG8MZ).
2. Please, prepare a long enough network cable to connect the PoE adapter and CPE, the network cable is connected to the LAN port of the CPE, and the other end is connected to the PoE port of the PoE adapter. Recommend to use a cat 5 (or above) shielded network cable with a ground wire.
3. Connect the PoE adapter PoE to CPE, and LAN to the Camera, PC, Router or Switch based on the network topology. The role of PoE is to provide power and data transmission for CPE.
4. The master CPE’s PoE adapter’s LAN connection monitors the Internet, and the slave CPE’s PoE adapter LAN connects cameras or routers and other equipment.

Note:
For point-to-point installation, the line of sight of the 2 wireless bridge brackets must be clear and cannot pass through the wall. The signal transmission angle of the bridge is 60 degrees. For point-to-multipoint installation, the angle of the slave bridge needs to be adjusted to ensure that it is within the 60-degree signal range of the main bridge. The antenna polarization direction is horizontal 60°/vertical 30°.

WiFi Function

1. The WiFi function is turned on by default for the master bridge.
2. WiFi SSID: CPE5G-5GXXX
3. WiFi PWD: zllinkcpe123456XXXXXX represents different channels, please refer to the comparison table in the user manual.
4. You can access the wireless bridge through your computer to set the SSID and new WiFi password. Please refer to the advanced settings section.

Application Case

Case 1: Point-to-point extended network WiFi range

• suitable for extending the network to second buildings, such as garages, shops, barns,etc.

Case 2: Point-to-point extended of surveillance cameras range

Case 3: Point-to-multiple-point extended surveillance cameras range

Case 4: Point-to-point extended surveillance cameras range

Advanced settings

Note: You can enable the device without advanced settings.

Computer Access

1. Connect the CPE to the computer Refer to the figure left to connect the CPE to the computer through a PoE adapter and an Ethernet cable.

2. Modify your computer’s IP address, make your computer’s IP and the bridge’s IP address be on the same network segment(LAN) so that you can access them.

   • Step 1: Find and open “Open Network and Sharing Center” on your computer. Tips： click the network icon in the lower right corner of the computer.
   • Step 2： Find and open the “Change adapter settings”, select “Local Area Connection” to right-click to open the network properties. Refer to the picture above to open it.
   • Step 3: Find and double-click open the “Internet Protocol Version 4(TCP/IPv4)”, choose the ” Use the following IP address” and enter IP address, subnet mask, Default gateway, and Preferred DDS server.

3. Change your computer’s IP address to 192.168.188.xxx (192.168.188.xxx cannot be the same as the IP of the CPE), then entry IP address is 192.168.188.xxx, the subnet mask is 255.255.255.0(Autofill), the Default gateway is 192.168.188.xxx, Preferred DDS server 192.168.188.xxx. You can use 192.168.188.2(xxx=2) in the reference picture to set.

4. On the login screen, the default user name and login password of the wireless bridge is “admin”, just enter the password login.
   Note: “admin” is not the password of the WiFi SSID, it is just the password for WEB access.

5. Login successfully, and go to settings.

6. In the wireless settings, turn off “Hide SSID”, then modify the SSID name and WiFi password, and finally click “Apply” to complete the setting.

Digital & IP & WiFi Correspondence Chart

You can check the SSID and password through this chart.

Troubleshooting

Technical Support and Service

• A. Thank you for your order and for using UeeVii Wireless Bridge, please read the manual carefully before use. If there are any problems during the use, please contact us in time;
• B. The installation of this device requires some network knowledge. If you can’t install it, please let us know or contact a professional.
• Tech Service Email: support@ueevii.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>