UeeVii CPE688 Gigabit Wireless Bridge User Manual

UeeVii CPE688 Gigabit Wireless Bridge

Tips
Thank you for ordering the UeeVii CPE688 Wireless Bridge. Please read this manual carefully before use. The installation of this device requires some network knowledge. If you encounter any problems please get in touch with us promptly at the email below or contact a professional. Customer Service Email: [email protected]

Overview

Introduce
UeeVii CPE688 is a long-distance 5.8G wireless transmission device. lt uses wireless communication technology to transmit network data using air as a medium to perform long-distance point-to-point or point-to-multi-point interconnection. The working data link layer realizes the interconnection of local area networks. The transmission distance can reach up to 5 km. CPE is widely used in highways, reservoir river monitoring, elevator monitoring systems, site crane monitoring systems, port terminal monitoring systems, marine aquaculture monitoring systems, etc. Point-to-point extends network WiFi range, extend the network in the house to your barn, garage, church, warehouse, and even neighbour’s house through wireless bridge signal transmission—no need to install a new modem and pay for it every month, saving you money.

Highlights

1. Transmission using 5.8 GHz wireless technology；
2. Gigabit (1000Mbps) RJ45 LAN / PoE port；
3. Built-in 14dBi high gain Wi-Fi dual polarization antenna；
4. IEEE802.11ac , IEEE802.11n, IEEE802.11a , IEEE802.3u；
5. Transmission distance up to 5km (Line of Sight)；
6. Master bridge supports Wi-Fi hot spot access；
7. Multiple codes to pair master bridge and slave bridge are easy to use；
8. Wireless distribution system mode, video network dual compatible；
9. Supports point-to-point mode (Master to one client included) and point-to-multipoint mode (Master to multiple clients – sold separately);
10. Dynamic MIMO power saving mode (DMPS) and APSD；
11. Requires 24V PoE power supply (included), easy to install and deploy；
12. Provides WEB GUI access management and configuration.

Important Certification

Model: CPE688 2A6EJ-CPE450

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Specifications

144.4Mb1p4s.,41M3,07M2,.21M15, .665MM,,

11a: 547M.8,M4,84M3,.33M6M, 2, 82.49M,, 1281M.7,M12M, 9M, 6Mbps

Transfer method| Direct Sequence Spread Spectrum(DSSS)
Modulation| OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK
Protocol standard

Agreement

| CIEEE802.11ac IEEE802.11n,IEEE802.11a ,IEEE802.3u

NSDMISA4/, CNAD, ITSC5P/IP, IPX/SPX, NetBEUI, DHCP, NDIS3,

 |
Frequency Range| 5.8GHz:5180MHz ~5825MHz
Power| ≤3W, PoE 24V~1A ,DC 12V~1A
Antenna| 14dBi,Horizontal 60°/Vertical 60°
WEP GUI| Support
---|---
Telnet| Support
Serial| Support
Safety| WEP 64/128bits,WPA,WPA2,802.1x
Temperature| -22～149°F
Box Size & Weight| 13.89.82.3 inch & 2.6 lb
Protection Level| IP66

Package Included

• 2 * CPE688 Gigabit Bridge
• 2 * Gigabit PoE Adapter (24V)
• 2 * Cat 5e Network Cable
• 2 * Metal Hoop
• 1 * User Manual

Interface Details

Button Operation

Setup/Reset Button
Press and hold for 10S to reset the wireless bridge; in setup mode, short press once to toggle a different character to pairing.

A-B Button
Pushing the button to “A” indicates that the bridge acts as the master bridge(transmitter), and pushing the button to “B” indicates that the bridge acts as the slave bridge (receiver).

LED Indicator Details

be on, not connected the WLAN light is not bright.
LAN1/LAN2| The data connection is successful, the LED light is on, otherwise, it is not bright.
PWR| Power indicator, the LED is on after the power is connected.
Digital display| Digital display LED display “H” indicates manual

configuration status.

Digital display| Digital display LED display “L” and flashing indicates

settings status.

Digital display| Digital display LED flashing indicates edit the config or

connecting.

Digital display| Display that a fixed number is solid, it means that the two

bridges are paired successfully and are working.

---|---
Point Light| A,B status lights, lighting is B mode, no lighting is A mode.

Quick Start

POE Power Supply
The CPE688 wireless bridge adopts a PoE power supply, which is easy to install and manage while saving costs.

1. According to the requirements, prepare a long enough network cable (Recommended within 2560 inches, must Cat 5e or up) to connect the wireless bridge and the PoE power supply. The PoE port of the PoE power supply is connected to the LAN port of the wireless bridge.
2. The LAN port of the PoE power supply is connected to the PC, router, and switch.

Point-to-Point Pairing Step

1. Switch one unit to A(Master Bridge) and one unit to B(Slave Bridge);
2. Connect the POE to each unit using the Ethernet cable and plug the POE in power;
3. Wait for them to power up, about 2 min;
4. Use the tiny reset button to click through until you get a channel with a letter 1,2,3,…, A,B,C,…,F, here used C;
5. Then on the other unit do the same. Both units need to be on the same channel;
6. Wait for 2-5 minutes to complete the pairing. When the number of the digital tube is solid and the signal light on the side turns on, it means the pairing is successful;
7. Finally connect other devices(Router, PC, Switch) and install them to the target location.

Point to Multi-point Pairing Step

1 master bridge with 3 slave bridges

1. Switch one unit to A(Master Bridge) and 3 units to B(Slave Bridge);
2. Connect the POE to each unit using the Ethernet cable and plug the POE in;
3. Wait for them to power up, about 2 min;
4. Use the tiny reset button to click through until you get a channel with a letter 1,2,3,…, A,B,C,..,F, here used C;
5. Then on the other 3 unit do the same. 4 units need to be on the same channel;
6. Wait for 2-5 minutes to complete the pairing. When the number of the digital tube is solid and the signal light on the side turns on, it means their pairing is successful;
7. Finally connect other devices(Router, PC, Switch) and install them to the target location.

Installation

1. Place the CPE to the selected position and adjust the CPE front panel orientation to be approximately the same as the selected direction, then use the ties to fix the CPE, the bracket is not included in the package. Recommended UeeVii Universal Bracket (ASIN: B09Y56M6Z9).
2. Please, prepare a long enough network cable(Recommended within 2560 inches, must cat 5 or up) to connect the PoE adapter and CPE, the network cable is connected to the LAN port of the CPE, and the other end is connected to the PoE port of the PoE adapter.
3. Connect the PoE adapter PoE to CPE, and LAN to Camera, PC, Router or Switch based on the network topology. The role of PoE is to provide power and data transmission for CPE.
4. The master CPE’s PoE adapter’s LAN connection monitors the Internet, and the slave CPE’s POE adapter LAN connects cameras or routers and other equipment.

Note:
For point-to-point installation, the line of sight of the 2 wireless bridge brackets must be clear and cannot pass through the wall. The signal transmission angle of the bridge is 60 degrees. For point-to-multipoint installation, the angle of the slave bridge needs to be adjusted to ensure that it is within the 60-degree signal range of the main bridge. The antenna polarization direction is horizontal 60°/ vertical 60°.

WiFi Function

1. The WiFi function is turned on by default for the master bridge.
   • WiFi SSID: admin
   • WiFi PWD: admin
2. You can access the wireless bridge through your computer to set the SSID and new WiFi password. Please refer to the advanced settings section.

Application Case

Case 1: Point-to-point extended network WiFirange suitable for extending the network to second buildings, such as garages, shops, barns, etc.

Case 2: Point-to-point extended of surveillance cameras range

Case 3: Point-to-multiple point extended surveillance cameras range

Case 4: Point-to-point extended surveillance cameras range

Advanced Settings

Computer Access

Connect the CPE to the computer
Refer to the figure left to connect the CPE to the computer through a PoE adapter and an Ethernet cable.

Modify your computer’s IP address,make your computer’s IP and the bridge’s lP address be on the same network segment (LAN) so that you can access them .

• Step 1: Find and open “Open Network and Sharing Center” on your computer. (Tips: click the network icon in the lower right corner of the computer.）
• Step 2: Find and open the “Change adapter settings”, and select “Local Area Connection” to right-click to open the network properties. Refer to the picture above to open it.
• Step 3: Find and double-click open the “Internet Protocol Version 4 (TCP/IPv4)choose ” Use the following lP address” and enter lP address, subnet mask, Default gateway, and Preferred DDS server.
• 3. Change your computer’s IP address to 192.168.255.xxx (192.168.255.xxx can not be the same as the lP of the CPE), then the entry lP address is 192.168.255.xxx, the subnet mask is 255.255.255.0 (Auto fill), Default gateway is 192.168.255.xxx, Preferred DDS server 192.168.255.xxx. You can use 192.168.255.2(xxx=2) in the reference picture to set.
• On the login screen, the default user name and login password of the wireless bridge is “admin” just entry the password log in.

Note:
“admin” is not the password of the WiFi SSID, it is just the password for WEB access.

Log in successfully, and go to settings.

In the wireless settings,turn off “Hide SSID”,then modify the SSID name and WiFi password, and finally click “Apply” to complete the setting.

Digital & IP & WiFi Correspondence Chart
You can check the SSID and password through this chart.

• （Ps:In this chart, SSIDs and Passwords are the default.）

Troubleshooting

Technical Support and Service

• A. Thank you for your order and for using UeeVii Wireless Bridge, please read the manual carefully before use. lf there are any problems during the use,please contact us in time;
• B. The installation of this device requires some network knowledge. lf you can’t install it, please let us know or contact a professional. Tech Service Email: [email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>