UeeVii CPE58G Point to Point Wireless Bridges 5.8G Outdoor User Manual

UeeVii CPE58G Point to Point Wireless Bridges 5.8G Outdoor

Note：
Thank you for order and using our product, please read the manual carefully before use. If there are any problems during the use, please contact us in time;

Customer Service Email: support@ueevii.com

Product Introduce

Uee Vii CPE58G wireless bridge is a 5G high-performance, high-speed outdoor long-distance wireless network bridge. It has the characteristics of long transmission distance, strong penetrating ability, and strong anti- interference ability. It supports intelligent channel analysis and automatic optimal channel selection. Realize point-to-point and point-to-multipoint outdoor coverage and applications. Very suitable for Internet expansion and monitoring range expansion of garages, barns, shops, docks, etc.

Package Included:

2 x CPE58G Bridge
2 x PoE Adapter
2 x Network Cables
2 x Cable Ties
1 x English User Manual

Product Features:

1. 5.8Ghz PTP PTMP 2-pack wireless bridge
2. Wired network speed 100Mbps, transmission rate 900Mbps
3. 12dBi high gain antenna, support 2KM distance
4. Support 24V PoE power supply
5. Outdoor WiFi hotspot function
6. 2 x 10/100 Mbps RJ45 ports
7. Support dial-up pairing, easy to use
8. IP65 level outdoor waterproof

Product Specifications

Product Specifications

Interface & LED Details

1.  1 WAN 10/100Mbps RJ45 port, 1 LAN 10/100Mbps RJ45 port support PoE power supply.
2. 4 LED Indicator lights included PWR light, LAN light, WAN light, WiFi light.
   PWR Light: Solid means power supply is normal
   LAN Light: Solid means LAN port has been connected
   WAN Light: Solid means WAN port has been connected
   WiFi Light: Blinking state indicates normal operation

Display Details

The display screen will display the master and slave bridges, IP addresses, and signal strength, which can be viewed and modified by button operation. Refer to the following interpretation：
H060： “H” means master bridge，“060” means 60 channel.
C060： “C” means slave bridge，“060” means 60 channel.
A100： “A” means IP address“, 100” means xxx.xxx.xxx.100 IP Address.
P-11： “P” means signal intensity“, -11” means current signal intensity.

Button Operation

CPE58G Wireless Bridge

Model| CPE58G
CPU| MT7628DAN+MT7613AE
Flash| 8MB
DDR| 64MB
5G working  frequency band| 5.150GHz〜5.850GHz
WiFi protocol| 802.11a/n/ac
Antenna| 12dbi
5G EVM| 802.11a_54M: ≤-25 dB；802.11n_MCS7: ≤-28 dB； 802.11AC_MCS9:≤-32dB
Interface| 1 x WAN 10/100Mbps RJ45，1 LAN 10/100Mbps RJ45
POE| 24V ⎓  0.5A
Button| Reset,H-C Switch,F/S
Maximum power consumption| <8W
Dustproof and  waterproof| Ip65
Working  environment| Working temperature: -30°Cto55°C Storage temperature: -40°C to 70°C Humidity: 5%〜95% (non-condensing
Size| 168 88 47.6mm

Quick Start

1. PoE Power Supply
   The CPE58G wireless bridge adopts a PoE power supply, which is easy to install and manage while saving cost

1. According to the requirements, prepare a long enough network cable （ Recommended within 20 meters） to connect the wireless bridge and the PoE power supply. The PoE port of the PoE power supply is connected to the WAN port of the wireless bridge.
2. The LAN port of the PoE power supply is connected to the PC, router, and swtich.

Point to Point & Point to Multipoint Pairing

Point to point pairing: The master bridge and the slave bridge respectively initiate a connection by pressing the “RST” button for one second within one minute, and wait for about 2 minutes to complete the pairing. Point to multipoint pairing: The master bridge and multiple slave bridge respectively initiate a connection by pressing the “RST” button for one second within one minute, and wait for about 2 minutes to complete the pairing.

Installation

Installation requirements

1. It is recommended to install the wireless network bridge by holding a pole;
2. The 2 wireless network bridges must be installed face to face as much as possible, with no architectural obstacles in between, strong electricity, and strong magnetism.
3. The theoretical working distance of CPE58G wireless bridge is 2KM, and the actual application should be less than 2KM.
   

WiFi Function

1. he WiFi function is turned on by default for the master bridge, and the WiFi function is turned off by default for the slave bridges (can be turned on). Default WiFi SSID: Wireless 5.8G_xxxxxx Default WiFi PWD: 66666666 You can access the wireless bridge through your computer or mobile phone to set the SSID and new WiFi password.

Application Case

1. Point-to-point extended of surveillance cameras range
   
   

2. Point-to-multiple point extended of surveillance cameras ran
   
   

3. Point-to-point extended network WiFi range, suitable for second buildings, garages, shops, barns, etc
   
   

Advanced settings

Note:
You can enable the device without advanced settings

Computer Access

1. Connect the CPE to the computer
   Refer to the figure left to connect the CPE to the computer through a PoE adapter and an Ethernet cable.
   

2. Modify your computer’s IP address, make your computer’s IP and the bridge’s IP address be on the same network segment(LAN) so that you can access them.
   Step 1 : Find and open “Open Network and Sharing Center” on your computer.
   Tips: click the network icon in the lower right corner of the computer.
   Step 2: Find and open the “Change adapter settings”, select “Local Area Connection” to right-click to open the network properties. Refer to the picture above to open.
   Step 3: Find and double-click open the “Internet Protocol Version 4(TCP/IPv4)”, choose the ” Use the following IP address” and enter IP address, subnet mask, Default gateway, Preferred DDS server.

3. Change your computer’s IP address to 192.168.188.xxx (192.168.188.xxx cannot be the same as the IP of the CPE), then entry IP address is 192.168.188.xxx, subnet mask is 255.255.255.0(Autofill), Default gateway is 192.168.188.xxx, Preferred DDS server 192.168.188.xxx. You can use 192.168.188.2(xxx=2) in the reference picture to set.

4. Open a web browser. In the address bar of the web browser, enter the wireless bridge IP address (such as 192.168.188.253). Find the IP address of the bridge by clicking the “F” button of the wireless bridge. Example: A104 is displayed on the screen, then the IP address of the bridge is 192.168.188.104.
   

5. A login screen will appear, by default, the password of the wireless bridge is “admin”, just entry password login.
   
   Note : “admin” is not the password of the WiFi SSID, it is just the password for WEB access.

6. Login successful, go to setting.
   

Troubleshooting

1. Wireless interference
2. Distance is too long, or there are some walls between them
3. CPE’s angle in the wrong direction, weak signal

|

1. Use WiFi analysis to choose the best channel
2. CPE should be in the normal distance, and avoid the wall
3. Adjust the angle of CPE  according to signal strength

Wrong Password|

1. Forget the password
2. Input wrong password
3. Too much cookie
4. WiFi password is confused with the WEB access password

|

1. Press the “RST” button in 10s to reset the bridge, the default password is admin.
2. Re-input the password
3. Clear cookie, run arp -d to clear MAC table
4. WEB access user namer and password is “admin”

Can not login WEB|

1. Local IP is not  in the same network segment of CPE
2. IP is taken by other devices
3. LAN connection or ethernet cable has a problem
4. Too much  cookie, MAC address haven’t update

|

1. Ping 192.168.188.253 to see the connection status
2. Stop other devices or change to another IP address
3. Check LAN connection and Ethernet cable
4. Clear cookie, run arp-d to clear MAC address

System LED light off|

1. PoE power supply is not working
2. Some problem in CPE’s PoE port
3. Ethernet cable is loose, RJ45 port is wrong power current/voltage lower or wrong

|

1. Check if the PoE adapter
   or PoE switch work

2. Check if the PoE port of
   CPE is ok

3. Check if Ethernet cable
   is loose if Ethernet cable
   plugged into PoE port

4. Check if the voltage is
   normal, if the socket
   has problem if the input
   voltage of the PoE
   adapter is normal

Low transmission
Rate|

1. Packet Latency
2. Ethernet cable circuit
3.  Network virus attack
4. Too much access users
5. Network Cables type lower than Cat 5e?

|

1. 1Adjust the distance,
   angle and channel to
   decrease latency

2. Check if port isolated to
   avoid network virus and
   broadcast storm

3. Decrease the access
   users.

4. Change use a Cat 5e or
   above network cable..

Device always
dead|

1. Static electricity
2. Running time too long
3.  Lightning stroke

|

1. Make CPE or PoE
   adapter need a ground connection

2. Running time over 7 days, reboot it

3. After lightning, device PoE port broken or unstable better to deploy lightning conductor

Technical support and service

A. Thank you for your order and for using our product, please read the manual carefully before use. If there are any problems during the use, please contact us in time;B. The installation of this device requires some network knowledge. If you can’t install it, please let us know or contact a professional.
Tech Service Email: support@ueevii.com

Note：
Thank you for order and using our product, please read the manual
carefully before use. If there are any problems during the use, please
contact us in time;
Customer Service Email: support@ueevii.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>