WORX WX744L 20V Cordless Wood And Metal Crafter Instruction Manual

WORX WX744L 20V Cordless Wood And Metal Crafter

PRODUCT SAFETY

WARNING : Read all safety warnings and all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.

WARNING: This product can expose you to chemicals including lead and Di(2-ethylhexyl)phthalate (DEHP) which are known to the State of California to cause cancer, birth defects or other reproductive harm.For more information go to www.P65Warnings. ca.gov. The tool shall be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery. Use battery operated tool only with specifically designed battery pack. Use of any other batteries may create a risk of fire. When battery pack is not in use, keep it away from other metal objects like: paper, clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns or a fire. Do not incinerate the tool even if it is severely damaged. The batteries can explode in a fire.
ADDITIONAL SAFETY RULES FOR YOUR CRAFTER

1. Do not leave the crafter unattended when in use.
2. This product is designed for light domestic use only, it is not designed for industrial purposes and although every care has been taken to make the crafter safe, accidents can happen. By following the simple safety guide, you can avoid serious accidents.
3. Be aware that heat may be conducted to combustible materials that are out of sight.
4. To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Store indoors. Read instruction manual before using.
5.  Any older children allowed to use this tool should be supervised by an adult. Both parties must read and understand the operator’s manual.\

This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way. reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the applianceThis appliance is not intended for use by persons (including children) with  APPLIANCE

• * A short power-supply cord (or short detachable power-supply cord) is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord.

  • Extension cords (or longer detachable power-supply cords) are available and may be used if care is exercised in their use.
  • If an extension cord (or a long detachable powersupply cord) is used

1. The marked electrical rating of the detachable powersupply cord or extension cord should be at least as great as the electrical rating of the appliance;
2. If the appliance is of the grounded type, the extension cord should be a grounding type 3-wire cord
3. The longer cord should be arranged so that it will not drape over the countertop or tabletop where it can be tripped over, snagged, or pulled on unintentionally (especially by children).
4. A battery operated crafter with a detachable battery back shall be recharged only with the specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery.
5. Use battery operated crafter only with specifically designed battery pack. Use of any other batteries may create a risk of fire.
6. When battery pack is not in use, keep it away from other metal objects like: paper, clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns or a fire.
7. Do not incinerate this crafter even if it is severely damaged. The batteries can explode in a fire.
8. Rechargeable batteries should be removed from the appliance before being charged.
9. Exhausted batteries should be removed from the applicance and safely disposed of.
10.  If the appliance is to be unused for a long period, the battery should be removed.

WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Store indoors. Do not immerse in water. Read instruction manual before using. For Use only with WA3742 Charger. For Use only with WA7150 WA7151 hub. For use only with WA3520 WA3525 WA3575 battery. To reduce the risk of electric shock, Do not expose to rain. Store indoors. For use only with Worx WA3520 battery pack or additional battery packs listed in Operator’s Manual.

SAFETY WARNINGS FOR BATTERY PACK

• Do not dismantle, open or shred battery pack.
• Do not expose battery pack to heat or fire. Avoid storage in direct sunlight.
• Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or fire.
• Do not remove battery pack from its original packaging until required for use.
• Do not subject battery pack to mechanical shock.
• In the event of battery leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
• Observe the plus (+) and minus (–) marks on the battery back and equipment and ensure correct use.
• Do not use any battery pack which is not designed for use with the equipment.
• Keep battery pack out of the reach of children.
• Seek medical advice immediately if a cell or battery has been swallowed.
• Always purchase the battery pack recommended by the device manufacturer for the equipment.
• Keep battery pack clean and dry.
• Wipe the battery pack terminals with a clean dry cloth if they become dirty.
• Battery pack needs to be charged before use. Always use the correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions.
• Do not leave battery pack on prolonged charge when not in use.
• After extended periods of storage, it may be necessary to charge and discharge the battery pack several times to obtain maximum performance.
• Battery pack gives its best performance when it is operated at normal room temperature (68 °F ± 9°F) (20 °C ± 5 °C).
• When disposing of battery packs, keep battery packs of different electrochemical systems separate from each other.
• Recharge only with the charger specified by Worx. Do not use any charger other than that specifically provided for use with the equipment. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Retain the original product literature for future reference.
• Use only the battery pack in the application for which it was intended.
• Remove the battery pack from the equipment when not in use.
• Dispose of properly.

SYMBOLS

POSITEC Inc. has established a partnership with the RBRC Corporation to recycle any Positec batteries with the RBRC-call2recycle seal. For environmental protection, please do not discard batteries in the trash. After the batteries’ life cycle is ended, then please call 1-800-822-8837 for a free service that will properly dispose of the battery.

COMPONENT LIST

Not all the accessories illustrated or described are included in standard delivery.
TECHNICAL DATA

| **WX744L WX744L.X *| **

---|---|---
Rated voltage| 20 V  Max. **
Power input| 45 W
Max temperature| 400 °F-900 °F (200 °C-480 °C)
Battery type| Lithium battery
Machine weight (bare tool)| 0.12 lbs (54 g)

• X may be followed by one or two characters. All models are the same except model number and trademark. The suffix in models may be number from “1” to
  “99” or English letter “A” to “Z” or ‘’M1’’ to ‘’M9’’ which means different package or the various of accessories packed in the package.
  ** Voltage measured without workload. Initial battery voltage reaches maximum of 20 volts. Nominal voltage is 18 volts.

20V Hub/HubX

| WA7150| Input: 20 V       10 A Max.

Output: 20 V        10 A Max.

WA7151

| Input: 20 V       10 A Max.

Output 1: 20 V       10 A Max.

Output 2: 5 V       2 A (USB port)

Only use the appropriate accessories intended for this tool. Accessory information can be found on the product packaging, at a Worx dealer or on our website at www. worx.com.
MakerX series tools and 20V Hub/HubX are specially designed to work together, so do not attempt to use any other devices.

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the instruction book carefully.
ASSEMBLY

• Assemble the crafter tips as shown in

• Connect the crafter and the hub.
  WARNING: Before operation, make sure the speed control button on the hub is at the“Min“ position. (See Fig. C)
  OPERATION
  Confirm the speed control button is set to “Min”. Grasp the tool by the grip. Press on/off switch on the hub. Then press and hold the power button on the crafter to start working. NOTE: The speed is fixed, and can not be adjusted by the speed control button on the hub. During operation, the crafter will enter into auto sleep with no movement for approximately 5 minutes or more. The temperature will drop to 400 °F (200 °C) and the crafter automatically turns off 10 minutes later. It will display “OFF”.
  WARNING : During initial use, the crafter may generate a light smoke due to elements heating, which is normal. While the crafter is heating, DO NOT touch the metallic parts near the tip and DO NOT remove or replace the tip. Never operate the crafter while people, especially young children are nearby. Be careful. The crafter remains hot after the work is concluded

• Press the on/off switch on the hub to turn off after use. NOTE: Use the trestle to place the crafter when not in use.

• Adjust temperature as needed. Press on/off switch on the hub. Use “+” or”-” button to adjust temperature (the temperature will increase / decrease by 20 °F (10 °C) each time the “+” or “-” button is pressed). NOTE: The temperature cannot be adjusted during the heating or cooling process.

• Switch °F and °C as needed. Press on/off switch on the hub. With the crafter turned off, press both “+” and ”-” button and “UNI” will be shown on the LCD display. Then press both “+” and ”-” button to switch the temperature mode. After selection, wait for 3 seconds and then it will display “OFF”.

•  Your Wood & Metal Crafter comes with an optional silicon Comfort Sleeve. To enhance the grip, simply slide the sleeve over the nose of the tool.

MAINTENANCE
Remove the battery before carrying out any adjustment, servicing or maintenance.
There are no user serviceable parts in your power tool. Never use water or chemical cleaners to clean your power tool. Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor ventilation slots clean. Keep all working controls free of dust. Occasionally you may see sparks through the ventilation slots. This is normal and will not damage your power tool. Store the accessories in a dry place.

www.worx.com
Copyright © 2020, Positec. All Rights Reserved. AR01530700

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>