MOUNTUP MU6004 Desk Mount Dual Monitor Stand Instruction Manual

June 14, 2024
MOUNTUP

MOUNTUP MU6004 Desk Mount Dual Monitor Stand Instruction Manual
MOUNTUP MU6004 Desk Mount Dual Monitor Stand

If you have any questions, please feel free to contact our customer service via Amazon.

WARNING!

If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help.

Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.

The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

PACKAGE CONTENTS


DO NOT EXCEED WEIGHT CAPACITY.

ASSEMBLY STEPS

STEP 1: Apply Pads To The Base Bottom

Paste the Pad (E1) onto the Base (E)

ASSEMBLY STEPS

STEP 2: Clamp Installation Or Grommet Base Installation

OPTION A: Clamp Installation
Loosen Bolts (B4) by using 5mm Allen Key (I), Then align the screw hole on the Base (E), and then lock the Screw (B4) with a 5mm Allen Key (I).

ASSEMBLY STEPS

Fix the Decorative Cover (C) to the Base (E) and fix the bracket on the table by tightening the Clamp (B).Use a 5mm Allen Wrench (I).

ASSEMBLY STEPS

OPTION B: Grommet Base Installation
Use 5mm Allen Key(I) to detach Clip Plate(B2)and Bolt Y(B3) from Clamp(B).

ASSEMBLY STEPS

Use Bolt Y (B3) through the screw hole on Bracket (B1) to fix the Base (E) and the table board together

ASSEMBLY STEPS

STEP 3 : Arm Installation

Install Arm (A),Fixator(H) ,Wire Clip (G) on the base in sequence as shown below.
Make sure to tighten the Fixator(H) to desired place with 5mm Allen Key.
Adjust the tightness of the bolt of Arm(A) to make the rotation flexible.

Arm Installation

STEP 4 : Attach Monitor

OPTION A: Flat Back Monitor

Attach the VESA Plate (D) to back of monitor and secure with Screws(M-A) with Washers(M-C ) using 5 mm Allen Key (I). Avoid excessive tightening screws damage the monitor.

Attach Monitor

OPTION B: Curved Back Monitor

Attach the VESA Plate (D) to back of monitor and secure with screws (M-B) with Washers (M-C)and Spacer(M-D)using 5 mm Allen Key (I). Avoid excessive tightening screws damage the monitor.

Curved Back Monitor

NOTE: Hand tighten screws to avoid over tightening.

STEP 5 : Hang Monitor

Slide the monitor onto the head of swivel arm. Install the Security Bolt (F).
Make sure the security bolt is tightened before you rotate the monitor.

Hang Monitor

Refer to below illustrations to adjust tilting angle of your monitor.

Problem:
If monitor face down

Solution:

  1. Loosen the tilting bolt.
  2. Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
  3. Retighten the tilting bolt to fix the intended angle.

STEP 6 : Adjust Tension

For intended functioning of the mount, you may need to adjust the tension of Arm (A) in accordance with your monitor weight by 6 mm Allen Key (J).

Adjust Tension 

Note1:
Be sure to keep the arm in horizontal position during adjustment.
Or else it would be difficult to adjust the mount or damage the mount.


Situation 1: Arm falls down

Upper Arm with monitor falls down and fails to stay where intended.

Solution:
Turn the inside screw counter clock wise(“+”direction) to increase gas spring tension until the arm can stay as intended.

Situation 2: Arm rises up
Upper Arm with monitor rises up and fails to stay where intended.

Solution:
Turn the inside screw clockwise(“-”direction) to decrease gas spring tension until the arm can stay as intended.

Note2:
For how many circles the screw should be turned, please refer to the table below.

Monitor Weight 2kg 3kg 4kg 5kg 6kg 7kg 8kg 9kg
Circles (AT LEAST) min 2 4 6 8 10 12 15

STEP 7 : Cable Management

Remove bottom plastic covers from gas spring Arm (A) .Run cables from monitor through bottom of gas spring Arm (A). Then cover the Wire Cap (A1) onto the upper arm of the Arm (A).
Reattach plastic covers as shown in diagram.

Cable Management

Adjust as Desired

Adjust as Desired

Product Dimensions

Product Dimensions

CAUTION AND MAINTENANCE:

  • Never allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals