phrozen Sonic 4K 2022 Gingiva Mask Resin User Guide

phrozen Sonic 4K 2022 Gingiva Mask Resin

Outline
Before printing the perfect object, it is important to first understand the material limitations we are handling and how it can be successfully printed under various conditions. With this in mind, Phrozen provides the following design suggestions to help you better understand the properties of each material and how you can best utilize them to bring your wildest creation to life.

Section 1

TDS

Liquid Properties
Viscosity at 25°C (77°F)| cP| 1900-2000| ASTM D1475
Liquid Density| g/cm³| 1.18| ASTM D7867

All testing specimens are printed using Phrozen Sonic 4K 2022 or Sonic XL 4K 2022, and post-cured using Phrozen Cure V2 or Phrozen Cure Mega.

Section 2

Printing

Printing Parameters

Printing Suggestions

Printing
Mix the resin well before pouring it into the vat.

Cleaning
After removing the printed object from the building stage, use an ultrasonic cleaner and isopropyl alcohol (IPA) for 10 minutes to remove uncured resin from the surface. Make sure that the object has been thoroughly cleaned, then leave it in a cool, well-ventilated place for at least 30 minutes without exposure to light. Alternatively, you may gently apply compressed air to dry the printed object.

Post-Curing
Put the printed object inside a glass container and pour glycerol until the object is fully immersed. Use Phrozen post-curing lamps (Cure V2, Cure Luna, Cure Mega) or other post-curing lamps with the same wavelength to cure printed objects for 30 minutes. After curing, remove the object and rinse it with water to eliminate any slimy feeling from the glycerol. Then, wipe it clean with paper towels.

Section 3

Design Specifications

Note : All indicators are limited to each resin; the value will vary with different machines and environmental conditions.※

Minimum Unsupported Wall Thickness
This indicator shows the minimum wall thickness that can be printed independently with no support without causing any bending or breaking.
Recommended thickness：≥ 0.6 mm

Size Tolerance, X-Y plane
This indicator shows the minimum dimensional tolerance between the hole and the column parallel to the XY plane.
Recommended tolerance：≥ 0.08 mm

Minimum Pin Diameter
This indicator shows the minimum column diameter of pillars and supports that can be printed independently without bending or breaking.
Recommended diameter：≥ 0.5 mm

Minimum Hole Diameter, X-Y plane
This indicator shows the minimum hole diameter that can be successfully printed parallel to the XY plane.
Recommended diameter：≥ 1.5 mm

Minimum Hole Diameter, X-Y plane
This indicator shows the minimum hole diameter that can be successfully printed parallel to the XY plane. Recommended diameter：≥ 1.5 mm

Minimum Hole Diameter, X-Y plane
This indicator shows the minimum hole diameter that can be successfully printed parallel to the XY plane.
Recommended diameter：≥ 1.5 mm

Maximum Horizontal Bridge Span
This indicator shows the maximum width between the supporting walls that can be printed without deforming the bridge.
Recommended width： 4 mm

Minimum Hole Diameter and Engraved Detail Width, Z-Axis, at 0.05mm Layer Height
This indicator shows the minimum hole diameter and engraving groove width that can be successfully printed on the Z-axis with a layer thickness of 0.05mm.

Recommended diameter：≥ 1.5 mm
Recommended width：≥ 0.08 mm

Section 4

Applications

Dental Work Model

Documents / Resources

| phrozen Sonic 4K 2022 Gingiva Mask Resin [pdf] User Guide
Sonic 4K 2022 Gingiva Mask Resin, Sonic 4K 2022, Gingiva Mask Resin, Mask Resin, Resin
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>