NEO TOOLS 17-084a Glue Gun Instruction Manual

NEO TOOLS 17-084a Glue Gun

Loading
The product uses a power supply with an output voltage of 4 V and an amperage of 1-2 A. It is not permitted to use a power supply with different parameters. The device must be switched off during charging. The red LED indicates charging. The green LED indicates that the device is fully charged. Do not use the device during charging.

Placement of the adhesive insert.
Place the glue cartridge by inserting it through the rear opening of the gun as far as it will go.

Working with the device

• The product should be fully charged using a suitable power supply before use.
• Insert a glue cartridge with a diameter of 6.7 – 7.9 mm. Sliding the switch to the ON position will start the device, which will go into the warm-up state. The blue LED will light up. After 3 – 5 minutes the unit will warm up. Press the trigger to squeeze out the glue.
• Do not remove the unfinished adhesive cartridge during use. For the next use, simply reheat the device.
• The red LED indicates that the device is charging, the green LED a full charge and the blue LED will turn off if there is no power.

Warning

• The cartridge should be replaced when the unit is switched off.
• Read the instructions carefully to minimise the risk of fire or injury.
• Eye protection should be worn.
• Do not dismantle the device, crush it or throw it into a fire.
• The room temperature during charging should be between 5 – 40°C. Beware of explosion or ignition.
• Exposing the battery to mechanical damage through impact can cause a short circuit, ignition or explosion.

QUESTIONS AND ANSWERS

Why are the charging times for the same battery different?
Battery charging time depends on a number of factors. A high level of charge will result in a shorter charging time. A low charge level in combination with a low ambient temperature can result in a long charging time. A very high battery temperature will trigger an internal protection device, which will stop charging. The same will happen at low temperatures below -5°C. In this situation, remove the battery from the device and wait until it has reached the correct temperature before charging again. Do not charge the second battery immediately after charging the first one as there is a risk of overheating. Wait at least 15 minutes.

Why is the run time of the same battery different?
Long periods of non-use of the battery will result in a reduction in its operating time. This is caused by the battery discharging itself. Charging and discharging the battery several times will solve the problem. The battery will discharge faster with intensive use. Do not charge when the ambient temperature is below -5°C or above 45°C. This will adversely affect the efficiency of the battery.

Why doesn’t the glue come out immediately when the trigger is pressed after the first charge?
The glue flow channel is empty when first used. Only after it has been filled by the melted glue is it possible for the glue to flow freely. This is a normal phenomenon.

Disposal of the battery
In order to protect the environment and maintain safe conditions, dispose used batteries correctly. Please consult your local waste disposal service for appropriate information. The battery should be fully discharged and wrapped in tape to avoid leakage and short circuits. Do not attempt to disassemble or open the battery.

Safety requirements

• The locking screw may come into contact with the wire inside the unit during assembly. Hold the glue gun by the handle during operation.
• The accessory, nozzle and nozzle guard heat up during operation.

INDICATIONS

Fig. A

1. Adhesive insert (7.3 ± 0.6 mm)
2. Nozzle cover
3. Nozzle (1.5 mm)
4. Drain
5. Base
6. On/off switch
7. USB input
8. LED
9. Glue cartridge input
10. Glue applicator
11. USB cable

Fig. B

1. Adhesive insert
2. The hole through which the adhesive insert is visible after insertion.

It is recommended to use accessories from the manufacturer or good brands. Accessories should be selected accordingly. Use the instructions or information on the packaging.

PARAMETERS

Glue gun 17-084

Parameter| Value
Supply voltage| 4V DC, USB

power supply

Battery capacity| 2600 mAh
Charging time| 4h
Working time| 60-100 min
Glue insert diameter| 7~8mm
Glue temperature| 80°C – 140°C
Nozzle diameter| 1.5 mm
Performance| 360-600g/h
Mass| 0.19 kg
Year of production|

DIODY:
Blue colour: device heating up.
Red: charging.
Blue: battery fully charged.
Blue LED off: no power supply.

ACCESSORIES

• USB cable – 1 pc.
• Operating instructions – 1 pc.
• Base – 1 pc.

WARNING! This equipment may be used by children 8 years of age and older and by persons with limited physical, sensory or mental abilities or persons without experience and knowledge, if they are supervised or have been instructed in the safe use of the equipment and understand the hazards that result from such use. Children must not play with the equipment. Without supervision, children must not clean the equipment or perform user-level maintenance.

ENVIRONMENTAL PROTECTION
Electrically-powered products should not be disposed of with household waste, but should be taken to appropriate facilities for disposal. Contact your product dealer or local authority for information on disposal. Waste electrical and electronic equipment contains environmentally inert substances. Equipment that is not recycled poses a potential risk to the environment and human health.

“Grupa Topex Spółka z ograniczoną odpowiedzialnością” Spółka komandytowa with its registered office in Warsaw, ul. Pograniczna 2/4 (hereinafter: “Grupa Topex”) informs that all copyrights to the content of this manual (hereinafter: “Manual”), including, among others. Its text, photographs, diagrams, drawings, as well as its composition, belong exclusively to Grupa Topex and are subject to legal protection under the Act of 4 February 1994 on Copyright and Related Rights (ie Journal of Laws 2006 No. 90 Poz. 631, as amended). Copying, processing, publishing, modification for commercial purposes of the entire Manual and its individual elements, without the consent of Grupa Topex expressed in writing, is strictly prohibited and may result in civil and criminal liability.

EU Declaration of Conformity

Manufacturer: Grupa Topex Sp. z o.o. Sp.k., Pograniczna 2/4 02-285 Warszawa
Product: Glue gun
Model: 17-084
Trade name: NEO TOOLS
Serial number: 00001 ÷ 99999

This declaration of conformity is issued under the sole responsibility of the manufacturer.
The product described above complies with the following documents: Electromagnetic Compatibility Directive 2014/30/EU
RoHS Directive 2011/65/EU as amended by Directive 2015/863/EU

And meets the requirements of the standards:
EN 55014-1:2017+A11; EN 55014-2:2015;
EN IEC 63000:2018

This declaration relates only to the machinery as placed on the market and doe not include components added by the end user or carried out by him/her subsequently.
Name and address of the EU resident person authorised to prepare the technic dossier:
Signed on behalf of:
Grupa Topex Sp. z o.o. Sp.k.
2/4 Pograniczna Street
02-285 Warsaw

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>