NEO TOOLS 75-106 Cross Line Laser User Manual
- June 14, 2024
- NEO TOOLS
Table of Contents
TRANSLATION (USER) MANUAL
CROSS LASER 75-106
75-106 Cross Line Laser
75-106
CAUTION : Before using the appliance, read these instructions carefully
and keep them for future reference. Failure to observe the safety precautions
in this manual may result in damage to the appliance and may cause personal
injury.
WARNING : Do not look directly into the laser beam! The following safety
rules must be observed:
SAFETY INFORMATION
- No modifications may be made to the unit.
- Use the laser device in accordance with the manufacturer’s recommendations.
- It is recommended to carry out an accuracy check before first use and periodic checks during the lifetime of the device.
- Do not point the laser beam towards the eyes of bystanders or animals. Laser radiation can damage the eye.
- Always ensure that the laser light is not directed at reflective surfaces. A reflective surface could reflect such a laser beam towards the operator, or towards third parties.
- Do not allow children to operate this appliance. Do not allow children in the work area during set-up and use of the appliance.
- Do not store the laser in direct sunlight or in a place with high temperatures. The casing and some components are constructed of plastic and exposure to temperature can cause degradation of the material.
- Store unused equipment in a dry place out of the reach of children.
- If storing for a long time, remove the battery to prevent possible damage.
- Do not replace the laser unit with another type. All repairs should becarried out by the manufacturer’s service department.
PURPOSE
- The machine is designed for the precise determination of horizontal and vertical lines. It is equipped with a horizontal laser and two vertical lasers to mark three 360° planes, intersecting at 90°. The unit also has a laser lock function, making it possible to trace straight lines at any angle.
During operation, act strictly in accordance with the following instructions
to ensure the best possible performance of the device.
Any use other than that described below is not permitted and may lead to
damage to the product.
EXPLANATION OF THE PICTOGRAMS USED
- Caution laser radiation!
- Caution laser radiation – do not look into the beam
- Read the Operating Instructions and observe the warnings and safety conditions contained therein.
- Recycling
DESCRIPTION OF THE GRAPHIC PAGES
The numbering below refers to the components of the unit shown on
the graphic pages of this manual:
- Switch
- Operating indicator light
- Change function button
- Tripod thread
- Battery cover
- Spigot
- Ball adapter
- Knob
- Buckle
- There may be differences between the drawing and the product
EQUIPMENT AND ACCESSORIES
- Tripod
- Cover
BATTERY REPLACEMENT
- To unlock the battery cover (5), gently push the cover in the direction of the arrow.
- Insert 2 new AA batteries (1.5 V), taking care to ensure their correct polarity.
- Close the battery cover and then slide the cover in the opposite direction of the arrow.
HANDLE OPERATION
- Attach the crossed laser to the bracket by screwing the threaded ferrule (6) into the tripod thread on the laser base.
- The ball adapter (7) allows the laser to be positioned in any position from 0 to 90°.
- The knob (8) allows the laser position to be locked.
- The clamp (9) allows the handle to be fixed to the chosen surface.
LASER OPERATION – SELF-LEVELLING FUNCTION
- The self-levelling crossed laser NEO 75-106 is switched on by pushing the switch (1) to the “ON” position. This unlocks the laser and the self-levelling process takes place.
- To lock the laser in the desired position, push the switch (1) to the “OFF” position and the laser switches off, remaining in the locked state.
- To switch on the laser beam when it is locked (off), hold down the button (3) marked “+” for approximately 2-3 seconds.
- Turning off the laser beam on a device that is in the locked state is possible by holding down button(3) ‘+’ again for approximately 2-3 seconds.
- When the laser is in the locked state, the (3) “+” button is only used to switch the laser beam on and off.
- The laser is additionally equipped with an indication that the acceptable level of lens deflection has been exceeded.
- When the level of deviation is exceeded, the red illumination at the top of the head turns on and the laser itself shuts down.
TECHNICAL DATA
Cross laser 75-106
Parameter| Value
Supply type| 2x AA 1.5V
Laser power| <1 mW
Laser wavelength| 520 nm
Laser class| II
Laser working range| Max. 15 m
Weight (excluding accessories and
batteries)| 0.17 kg
Year of production| 2023
ENVIRONMENTAL PROTECTION
Electrically-powered products should not be disposed of with household waste,
but should be taken to appropriate facilities for disposal. Contact your
product dealer or local authority for information on disposal. Waste
electrical and electronic equipment contains environmentally unfriendly
substances. Equipment that is not recycled poses a potential risk to the
environment and human health.
“Grupa Topex Spółka z ograniczoną odpowiedzialnością” Spółka komandytowa with
its registered office in Warsaw, ul. Pograniczna 2/4 (hereinafter: “Grupa
Topex”) informs that all copyrights to the content of this manual
(hereinafter: “Manual”), including, among others. Its text, photographs,
diagrams, drawings, as well as its composition, belong exclusively to Grupa
Topex and are subject to legal protection under the Act of 4 February 1994 on
Copyright and Related Rights (ie Journal of Laws 2006 No. 90 Poz. 631, as
amended). Copying, processing, publishing, modifying for commercial purposes
the entire Manual and its individual elements, without the consent of Grupa
Topex expressed in writing, is strictly prohibited and may result in civil and
criminal liability.
EU Declaration of Conformity
Manufacturer: Grupa Topex Sp. z o.o. Sp.k., Pograniczna 2/4 02-285
Warszawa
Product: Cross laser
Model: 75-106
Trade name: NEO TOOLS
Serial number: 00001 ÷ 99999
This declaration of conformity is issued under the sole responsibility of the
manufacturer.
The product described above complies with the following documents:
Electromagnetic Compatibility Directive 2014/30/EU
RoHS Directive 2011/65/EU as amended by Directive 2015/863/EU
And meets the requirements of the standards:
EN 61000-6-1:2007; EN 61000-6-3:2007/+A1:2011;
EN IEC 63000:2018
This declaration relates only to the machinery as placed on the market and
does not include components added by the end user or carried out by him/her
subsequently.
Name and address of the EU resident person authorised to prepare the technical
dossier:
Signed on behalf of:
Grupa Topex Sp. z o.o. Sp.k.
2/4 Pograniczna Street
02-285 Warsaw
TOPEX GROUP Quality Officer
Warsaw, 2023-03-20
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>