HKC Q27CMA11 Intelligent Signage Instruction Manual

HKC Q27CMA11 Intelligent Signage Instruction Manual

Note
Thank you for choosing the product！In order to ensure your safe use of this product, Before using this product, please read the user manual carefully and keep it properly.

Installation guide

1. Remove the plastic wrap from the cardboard box and remove the top cover of the plastic wrap.
   
   More Than 2 Adults Are Recommended To Work

2. Takeout The Chassis And The Middle Styrofoam.
   
   *Please Prepare A Cross Screwdriver Before Assembly

3. Take out the product and put the screen face down on styrofoam, as shown in the fo Uowing picture.
   

4. Place the chassis in the card slot of styrofoam, pass the power cord at the bottom of the lower rod through the round hole of the chassis, and connect it with the power cord of the chassis.
   

5. Fasten the chassis and lock the mounting cover with locking screws (as shown in the figure below).
   

Appearance Introduction

1. Audio output interface

2. Display menu key

3. Adjustment key (adjust volume and brightness)

4. Switch power supply of the whole machine

5. Power display
   

6. USB-A: Transfer Data

7. HDMI (HDMI device connection for use) 7

8. Type-C 2.0 interface

9. Type-C interface (fully functional)

10. DC power interface
    

OSD function operation

Press the menu key of the display once to activate the OSD menu on the screen. Short press the menu key or touch the exit key in the menu to exit the touch menu on the screen (the menu will automatically exit after about 9 seconds). Users of various functions of the display can customize the touch adjustment;

When the system sleeps, long press the menu key for 3 seconds to wake it up.

1. modulation
2. Brightness adjustment
3. Contrast adjustment
4. Type-C connection
5. HDMI connection
6. Switch back to Android
7. OD
8. Mute
9. Low blue light
10. FreeSync
11. reset
12. Move up menu
13. Move down menu
14. Exit menu

Connection and startup

Connection of signal lines

1. Supports HDMI signal connection, simply connect the monitor to the signal end using an HDMI cable
2. and 1.2 support Type-C signal connection, simply connect the display to the signal end using a Type-C cable
   Note: The Type-C interface at the signal end has external transmission function

Connecting USB peripherals
You can also connect USB/Type-C peripherals through the USB/Type-C expansion dock; When connecting peripherals, it defaults to the Android system. If you need to switch, you need to switch in the menu

Menu settings
Long press the menu key to wake up from sleep, and short press the menu key to activate the menu for settings

Basic Parameter

point capacitive touch screen

FCC warning statements:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The device has been evaluated to meet general RF exposure requirement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>