ULNA CPE609 Wireless Bridge User Manual

June 14, 2024
ULNA

ULNA CPE609 Wireless Bridge User Manual
HCP OVU11A IR-2-USB Transceiver HCP OVU11A IR-2-USB Transceiver User
Guide

Overview

Introduce
ULNA CPE412 is a long-distance 5.8G wireless transmission device. It uses wireless communication technology to transmit network data using air as a medium to perform long-distance point-to-point or point-to-multipoint interconnection. The working data link layer realizes the interconnection of local area networks. The transmission distance can reach up to 3km. CPE412 Video Bridge Transmission usually consists of two devices in AP and Client mode respectively. On the Client-side (Receiving side) CPE connects with IP Camera, at the AP side (Transmitting side) CPE connects with a video recorder. The AP can be receiving wireless data transmitted from multiple Clients, and it is easy and convenient for centralized management of the remote equipment. CPE is widely used in highways, reservoir river monitoring, elevator monitoring systems, site crane monitoring systems, port terminal monitoring systems, marine aquaculture monitoring systems, and so on. Point to point extend network WiFi range, extend the network in the house to your barn, garage, church, warehouse, and even neighbor’s house through wireless bridge signal transmission. No need to install a new modem and pay for it every month, saving you money.

Highlights

  1.  Transmission using 5.8Ghz wireless technology;
  2. 100Mbps RJ45 LAN port;
  3. Built-in 16dbi high gain WiFi antenna;
  4. IEEE802.11ac IEEE802.11n,IEEE802.11a ,IEEE802.3u;
  5. Transmission distance up to 3km(Barrier-Free);
  6. Dialing to set the transmitter and receiver, is easy to use;
  7. WDS networking mode, video network dual compatible;
  8. Support point-to-point, point-to-multipoint mode;
  9. Dynamic MIMO power saving mode (DMPS) and APSD;
  10. Support 24V POE power supply, easy to install and deploy;
  11. Support WEB GUI access management device.

Specifications

Brand ULNA
Model CPE-412
CPU MT7620A+7612E
Flash 8MByte
DRAM DDR2 128MByte
Interface 10/100Mbps LAN1 & 10/100Mbps LAN1
Data rate

11a:54M,48M,36M,24M,18M,12M,9M,6Mbps11n:7.2M,14.4M,21.7M,28.9M,43.3M,57.8M,65M,72.2M,14.4M28.9M,43.3M,57.8M,86.7M,115.6M,130M,144.4Mbps
Transfer method| Direct Sequence Spread Spectrum(DSSS)
Modulation| OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK
Protocol standard| IEEE802.11ac IEEE802.11n,IEEE802.11a ,IEEE802.3u
Agreement| CSMA/CA,TCP/IP,IPX/SPX,NetBEUI,DHCP,NDIS3,NDIS4,NDIS5
Frequency Range| 4900~6100MHz
Power| ≤3W, POE 24V~1A/48V~0.5A
Antenna| 16dBi,Horizontal 60°/Vertical 30°
WEP GUI| Support
Telnet| Support
Serial| Support
Safety| WEP 64/128bits,WPA,WPA2,802.1x
Temperature| -30~65℃

Package Included

Package Included

2 CPE412 Wireless Bridge
2
POE Adapter (24V)
2 Cat 5e Network Cable
2
Metal Hoop
1 Mounting Screw Set
1
User Manual

Interface Details

Product Parts

Button Operation
Reset Button : Press and hold for 10S to reset the wireless bridge; in setup mode, short press once to toggle a different character to pairing. A-B Button: Pushing the button to “A” indicates that the bridge acts as the master bridge (transmitter), and pushing the button to “B” indicates that the bridge acts as the slave bridge (receiver).

LED Indicator Details

LED Indicator Details

LED Light Description
Signal Lights After the bridge is connected successfully, the WLAN

light will be on, not connected the WLAN light will not be lit.
LAN1/LAN2| The data connection is successful, the LED light is on, otherwise, it is not bright.
PWR| Power indicator, the LED is on after the power is connected
Digital Tube| Digital display LED display “H” indicates manual configuration status
Digital Tube| Digital display LED display “L” and flashing indicates settings status
Digital Tube| Digital display LED flashing indicates edit the config or connecting
Digital Tube| Display that a fixed number is solid, it means that the two bridges are paired successfully and are working.
Point Light| A, B status lights, lighting is B mode(Receiver), no lighting is A mode(Transmitter)

Quick Start

PoE Power Supply
The CPE412 wireless bridge adopts a PoE power supply, which is easy to install
and manage while saving costs.
Connection
According to the requirements, prepare a long enough network cable Recommended within 20 meters, must Cat 5e or up)to connect the wireless bridge and the PoE power supply. The PoE port of the PoE power supply is connected to the WAN port of the wireless bridge.
The LAN port of the PoE power supply is connected to the PC, router, and switch.\

Point to Point Pairing Step:

  1. Switch one unit to A(Transmitter ) and one unit to B(Receiver)

  2.  Connect the POE to each unit using the Ethernet cable and plug the POE in;

  3. Wait for them to power up, about 2 min;

  4. Use the tiny reset button to click through until you get a channel with a letter. 1,2,3,…, A,B,C,…,F, here used C;

  5. Then on the other unit do the same. Both units need to be on the same channel;

  6.  Wait for 2-5 minutes to complete the pairing. When the number of the digital
    tube is solid and the signal light on the side turns on, it means the pairing is
    successful;

  7. Finally connect other devices(Router, PC, Switch) and install them to the target location.
    (TIPS: Steps 1, 4 and 5 are already pre-set)

  8. Point to Multipoint Pairing Step:

Pole mount e.g. 1 master bridge with 3 slave bridges

  1.  Switch one unit to A(Master Bridge) and 3 units to B(Slave Bridge);
  2. Connect the POE to each unit using the Ethernet cable and plug the POE in;
  3.  Wait for them to power up, about 2 min;
  4. Use the tiny reset button to click through until you get a channel with a letter. 1,2,3,…, A,B,C,…,F, here used C;
  5. Then on the other 3 unit do the same. 4 units need to be on the same channel;
  6. Wait for 2-5 minutes to complete the pairing. When the number of the digital  tube is solid and the signal light on the side turns on, it means their pairing is successful;
  7. Finally connect other devices(Router, PC, Switch) and install them to the target location.

Installation

**Pole mount
Pole mount
Wall-mounted

Connect to the device Connect to the device
**

  1. Choose to pole mount or wall-mounted, adjust the CP bracket is not included in the package. Recommended ULNA Universal Bracket (ASIN: B0B5TWYHWC).
  2. Please, prepare a long enough network cable to connect the PoE adapter and CPE, the network cable is connected to the LAN port of the CPE, andthe other end is connected to the PoE port of the PoE adapter. Recommend to  use a cat 5(or above) shielded network cable with a ground wire.
  3. Connect the PoE adapter PoE to CPE, and LAN to Camera, PC, Router or Switch based on the network topology. The role of PoE is to provide power and data transmission for CPE.
  4. The master CPE’s PoE adapter’s LAN connection monitors the Internet, and the slave CPE’s PoE adapter LAN connects cameras or routers and other equipment

Note : For point-to-point installation, the line of sight of the 2 wireless bridge brackets must be clear and cannot pass through the wall. The signal transmission angle of the bridge is 60 degrees. For point-to-multipoint installation, the angle of the slave bridge needs to be adjusted to ensure that it is within the 60-degree signal range of the main bridge. The antenna polarization direction is horizontal 60°/vertical 30

 Application Case

Case 1: Point-to-point extended network WiFi range

Product Parts
Case 2: Point-to-point extended of surveillance cameras range
Product Parts

Case 3: Point-to-multiple point extended surveillance cameras range

Case 4: Point-to-point extended surveillance cameras range.
Slave Bridge

Master Bridge

Access to the WEB interface

Tips:
No need to enter the WEB interface wireless bridge can be used normally

  1. Computer Access Wireless Bridge, connect the CPE to the computer Refer to the figure left to connect the CPE to the computer through a PoE adapter and an Ethernet cable.
    Network Segment\(LAN\) s

  2. Modify your computer’s IP address, make your computer’s IP and the bridge’s IP address be on the same network segment(LAN) so that you can access them.
    Step 1 : Find and open “Open Network and Sharing Center” on your computer.
    Tips: click the network icon in the lower right corner of the computer.
    Step 2 : Find and open the “Change adapter settings”, select “Local Area Connection” to right-click to open the network properties. Refer to the picture above to open.
    Step 3 : Find and double-click open the “Internet Protocol Version 4(TCP/IPv4)”, choose the ” Use the following IP address” and enter IP address, subnet mask, Default gateway, Preferred DDS server.

  3.  Change your computer’s IP address to 192.168.255.xxx (192.168.255.xxx cannot be the same as the IP of the CPE), then the entry IP address is 192.168.255.xxx, the subnet mask is 255.255.255.0(Autofill), the Default gateway is 192.168.255.xxx, Preferred DDS server 192.168.255.xxx. You can use 192.168.255.105(xxx=5) in the reference picture to set.
    IP address

  4. On the login screen, the default user name and login password of the wireless bridge is “admin”, just entry password logLogin Password

  5. Login successful

Digital & IP & WiFi Correspondence Chart
You can check the SSID and password through this chart.

LED A IP B IP
0 192.168.255.100 192.168.255.200
1 192.168.255.101 192.168.255.201
2 192.168.255.102 192.168.255.202
3 192.168.255.103 192.168.255.203
4 192.168.255.104 192.168.255.204
5 192.168.255.106 192.168.255.205
6 192.168.255.106 192.168.255.206
7 192.168.255.107 192.168.255.207
8 192.168.255.108 192.168.255.208
9 192.168.255.109 192.168.255.209
a 192.168.255.110 192.168.255.210
b 192.168.255.111 192.168.255.211
c 192.168.255.112 192.168.255.212
D 192.168.255.113 192.168.255.213
E 192.168.255.114 192.168.255.214
F 192.168.255.115 192.168.255.215

Troubleshooting

Trouble Reason Solution

Packet Latency

| 1.  Wireless interference2.  Distance is too long, or there are some walls between them3.  CPE’s angle in the wrong direction, weak signal| 1.  Use WiFi analysis to choose the best channel2.  CPE should be in the normal distance, and avoid the wall3.  Adjust the angle of CPE according to signal strength

Can not login WEB

| 1.  Local IP is not in the same network segment of CPE2.  IP is taken by other devices3.  LAN connection or ethernet cable has a problem4.  Too much cookie, MAC address haven’t update| 1.  Ping bridge IP address to see the connection status2.  Stop other devices or change to another IP address3. Check LAN connection and Ethernet cable4.  Clear cookie, run arp -d to clear MAC address

System LED l ight off

| 1.  PoE power supply is not working2.  Some problem in CPE’s PoE port3. Ethernet cable is loose,RJ45 port is wrong power current/voltage lower or wrong| 1.  Check if the PoE adapter or PoE switch work2.  Check if the PoE port of CPE is ok3.  Check if Ethernet cable is loose if Ethernet cable plugged into PoE port4.  Check if the voltage is normal, if the socket has problem if the input voltage of the PoE adapter is normal

Low transmission Rate

| 1.  Packet Latency2.  Ethernet cable circuit3.  Network virus attack4.  Too much access users5.  Network Cables type lower than Cat 5e?| 1.  Adjust the distance, angle and channel to decrease latency2.  Check if port isolated to avoid network virus and broadcast storm4.  Decrease the access users.5. Change use a Cat 5e or above network cable.
---|---|---

Device always dead

|

1.  Static electricity2.  Running time too long3.  Lightning stroke

| 1.  Make CPE or PoE adapter need a ground connection2.  Running time over 7 days, reboot it3.  After lightning, device PoE port broken or unstable better to deploy lightning conductor

Technical Support and Service

A. Thank you for your order and for using ULNA Wireless Bridge, please read the
manual carefully before use. If there are any problems during the use, please contact us in time;
B. The installation of this device requires some network knowledge. If you can’t install it, please let us know or contact a professional. (There are also many installation videos of the bridge on the YouTube that you can refer to)
Tech Service Email: support01@ulnastore.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals