ULNA CPE988 Wireless Bridge User Manual

June 14, 2024
ULNA

ULNA CPE988 Wireless Bridge

ULNA CPE988 Wireless Bridge

Tips

Thank you for ordering and using ULNA CPE988 Wireless Bridge, please read the manual carefully before use. If there are any problems during the use, please contact us in time.
The installation of this device requires some network knowledge. If you can’t install it, please let us know or contact a professional.

Customer Service Email: support01@ulnastore.com

Overview

Introduce

ULNA CPE988 is a long-distance 5.8G wireless transmission device. It uses wireless communication technology to transmit network data using air as a medium to perform long-distance point-to-point or point-to-multipoint interconnection. The working data link layer realizes the interconnection of local area networks. The transmission distance can reach up to 5km.
CPE988 Video Bridge Transmission usually consists of two devices in AP and Client mode respectively. On the Client-side (Receiving side) CPE connects with IP Camera, at the AP side (Transmitting side) CPE connects with a video recorder. The AP can be receiving wireless data transmitted from multiple Clients, and it is easy and convenient for centralized management of the remote equipment.
CPE is widely used in highways, reservoir river monitoring, elevator monitoring systems, site crane monitoring systems, port terminal monitoring systems, marine aquaculture monitoring systems, and so on.
Point to point extend network WiFi range, extend the network in the house to your barn, garage, church, warehouse, and even neighbor’s house through wireless bridge signal transmission. No need to install a new modem and pay for it every month, saving you money.

Highlights
  1. Transmission using 5.8Ghz wireless technology
  2. 1000Mbps RJ45 LAN port, support Gigabit
  3. Built-in 16dbi high gain WiFi antenna
  4. IEEE802.11ac IEEE802.11n,IEEE802.11a ,IEEE802.3u
  5. Transmission distance up to 5km(Barrier-Free)
  6. Master bridge supports WiFi hotspot access
  7. Dialing to set the transmitter and receiver, is easy to use
  8. Support point-to-point, point-to-multipoint mode
  9. Dynamic MIMO power saving mode (DMPS) and APSD
  10. Support 24V POE power supply, easy to install and deploy
  11. Support WEB GUI access management device.
Specifications
Brand ULNA
Model CPE988
CPU MT7620A+7612E
Flash 8MByte
DRAM DDR2 128MByte
Interface 10/100/1000Mbps LAN x 1 & 10/100Mbps LAN x 1
Data rate 11a: 54M,48M,36M,24M,18M,12M,9M,6Mbps

11n: 7.2M,14.4M,21.7M,28.9M,43.3M,57.8M,65M,
72.2M,14.4M,28.9M,43.3M,57.8M,86.7M,115.6M,
130M,144.4Mbps 433Mbps
Transfer method| Direct Sequence Spread Spectrum(DSSS)
Modulation| OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK
Protocol standard| IEEE802.11ac IEEE802.11n,IEEE802.11a ,IEEE802.3u
Agreement| CSMA/CA,TCP/IP,IPX/SPX,NetBEUI,DHCP,NDIS3, NDIS4,NDIS5
Frequency Range| 4900~6100MHz
Power| ≤3W, POE 24V~1A/48V~0.5A
Antenna| 16dBi,Horizontal 60°/Vertical 30°
WEP GUI| Support
Telnet| Support
Serial| Support
Safety| WEP 64/128bits,WPA,WPA2,802.1x
Temperature| -30~65℃
Box Size & Weight| 11.811.52.7 inch & 2.2 LB

Package Included

  • 2 x CPE988 Gigabit Bridge
  • 2 x Gigabit POE Adapter (24V)
  • 2 x Cat 5e Network Cable
  • 2 x Metal Hoop
  • 2 x Mounting Screw Set
  • 1 x User Manual
    Package Included

Interface Details

Interface Details
Interface Details

Button Operation

Reset Button:
Press and hold for 10S to reset the wireless bridge; in setup mode, short press once to toggle a different character to pairing.
A-B Button:
Pushing the button to “A” indicates that the bridge acts as the master bridge (transmitter), and pushing the button to “B” indicates that the bridge acts as the slave bridge (receiver).

LED Indicator Details

LED Indicator Details

LED Light Description
WLAN Signal Lights After the bridge is connected successfully, the 5

grid green WLAN lights will be on; otherwise, only 1 grid green WLAN light will be on.
LAN1/LAN2| The data connection is successful, the LED light is on, otherwise, it is not bright.
PWR| Power indicator, the LED is on after the power is connected
Digital Tube| Digital display LED display “H” indicates manual

configuration status

Digital Tube| Digital display LED display “L” and flashing indicates settings status
Digital Tube| Digital display LED flashing indicates edit the config or connecting
Digital Tube| Display that a fixed number is solid, it means that the two bridges are paired successfully and are working.
Point Light| A, B status lights, lighting is B mode, no lighting is A mode.
RST Button| Click once to switch different characters, looping from0, 1, …, F. Characters represent channels.
RST Button| Long-press 10s on the “RST” button and the bridge will auto- reset.
A-B Button| The bridge switches the master and slave bridges through the A-B button, A represents the master bridge, and B represents the slave bridge.
PoE Port of Adapter| 24V power supply and data transmission
PoE Port of Bridge/LAN| Only data transmission and DC in, can’t power other devices

Quick Start

PoE Power Supply

The CPE988 wireless bridge adopts a PoE power supply, which is easy to install and manage while saving costs.
Quick Start

  1. According to the requirements, prepare a long enough network cable Recommended within 20 meters, must Cat 5e or up) to connect the wireless bridge and the PoE power supply. The PoE port of the PoE power supply is connected to the WAN port of the wireless bridge.
  2. The LAN port of the PoE power supply is connected to the PC, router, and switch.
Point to Point Pairing Step:
  1. Switch one unit to A(Master Bridge) and one unit to B(Slave Bridge)
  2. Connect the POE to each unit using the Ethernet cable and plug the POE in;
  3. Wait for them to power up, about 2 min;
  4. Use the tiny reset button to click through until you get a channel with a letter. 1,2,3,…, A,B,C,…,F, here used C;
  5. Then on the other unit do the same. Both units need to be on the same channel;
  6. Wait for 2-5 minutes to complete the pairing. When the number of the digital tube is solid and the signal light on the side turns on, it means the pairing is successful;
  7. Finally connect other devices(Router, PC, Switch) and install them to the target location.
    TIPS : Steps 1, 4 and 5 are already pre-set at factory)
Point to Multipoint Pairing Step

e.g. 1 master bridge with 3 slave bridges

  1. Switch one unit to A(Master Bridge) and 3 units to B(Slave Bridge);
  2. Connect the POE to each unit using the Ethernet cable and plug the POE in;
  3. Wait for them to power up, about 2 min;
  4. Use the tiny reset button to click through until you get a channel with a letter. 1,2,3,…, A,B,C,…,F, here used C;
  5. Then on the other 3 unit do the same. 4 units need to be on the same channel;
  6. Wait for 2-5 minutes to complete the pairing. When the number of the digital tube is solid and the signal light on the side turns on, it means their pairing is successful;
  7. Finally connect other devices(Router, PC, Switch) and install them to the target location.

Installation

Pole mount

Installation

Wall-mounted

Installation

Connect to the device

Installation

  1. Choose to pole mount or wall-mounted, adjust the CPE orientation, the bracket is not included in the package. Recommended ULNA Universal Bracket (ASIN: B0B5TWYHWC).
  2. Prepare a long enough network cable to connect the PoE adapter and CPE, the network cable is connected to the LAN port of the CPE, and the other end is connected to the PoE port of the PoE adapter. Recommend to use a cat 5 (or above) shielded network cable with a ground wire.
  3. Connect the PoE adapter PoE to CPE, and LAN to Camera, PC, Router or Switch based on the network topology. The role of PoE is to provide power and data transmission for CPE.
  4. The master CPE’s PoE adapter’s LAN connection monitors the Internet, and the slave CPE’s PoE adapter LAN connects cameras or routers and other equipment.

Note:
For point-to-point installation, the line of sight of the 2 wireless bridge brackets must be clear and cannot pass through the wall. The signal transmission angle of the bridge is 60 degrees. For point-to-multipoint installation, the angle of the slave bridge needs to be adjusted to ensure that it is within the 60-degree signal range of the main bridge. The antenna polarization direction is horizontal 60°/vertical 30°.

WiFi Function

  1. The WiFi function is turned on by default for the master bridge. The slave bridge is unable to provide WiFi, it is recommended to connect a new router.
    WiFi SSID: CPE5G-5GXXX
    WiFi PWD: zllinkcpe123456XXX
    XXX represents different channels, please refer to the comparison table in the user manual.

  2. You can access the wireless bridge through your computer to set the SSID and new WiFi password. Please refer to the advanced settings section.

Application Case

Case 1: Point-to-point extended network WiFi range

suitable for extending the network to second buildings, such as garages, shops, barns, etc.
Application Case

Case 2: Point-to-point extended of surveillance cameras range

Application Case

Case 3: Point-to-multiple point extended surveillance cameras range

Application Case

Case 4: Point-to-point extended surveillance cameras range

Application Case

Advanced Settings

Note : You can work the wireless bridge without advanced settings

  1. Computer Access Wireless Bridge, connect the CPE to the computer Refer to the figure left to connect the CPE to the computer through a PoE adapter and an Ethernet cable.
    Advanced Settings

  2. Modify your computer’s IP address, make your computer’s IP and the bridge’s IP address be on the same network segment(LAN) so that you can access them.
    Advanced Settings
    Step 1 : Find and open “Open Network and Sharing Center” on your computer.
    Tips : click the network icon in the lower right corner of the computer.
    Step 2 : Find and open the “Change adapter settings”, select “Local Area Connection” to right-click to open the network properties. Refer to the picture above to open.
    Step 3 : Find and double-click open the “Internet Protocol Version 4(TCP/IPv4)”, choose the ” Use the following IP address” and enter IP address, subnet mask, Default gateway, Preferred DDS server.

  3. Change your computer’s IP address to 192.168.255.xxx
    (192.168.255.xxx cannot be the same as the IP of the CPE), then the entry IP address is 192.168.255.xxx, the subnet mask is 255.255.255.0(Autofill), the Default gateway is 192.168.255.xxx, Preferred DDS server 192.168.255.xxx.
    You can use 192.168.255.105(xxx=2) in the reference picture to set.
    Advanced Settings

  4. On the login screen, the default user name and login password of the wireless bridge is “admin”, just entry password login.
    Note:
    “admin” is not the password of the WiFi SSID, it is just the password for WEB access.

  5. Login successful, go to setting.
    Advanced Settings

  6. When you want to change “SSID” information and password, please turn off “Digit on/off” first. And then turn off “Hide SSID” and modify the SSID name and WiFi password, and finally click “Apply” to complete the setting.
    Advanced Settings

Digital & IP & WiFi Correspondence Chart

You can check the SSID and password through this chart.

LED A IP B IP 5.8G ID SSID Password
0 192.168.255.100 192.168.255.200 0 CPE5G_5G0 zllinkcpe1234560
1 192.168.255.101 192.168.255.201 36 CPE5G_5G36 zllinkcpe12345636
2 192.168.255.102 192.168.255.202 40 CPE5G_5G40 zllinkcpe12345640
3 192.168.255.103 192.168.255.203 44 CPE5G_5G44 zllinkcpe12345644
4 192.168.255.104 192.168.255.204 48 CPE5G_5G48 zllinkcpe12345648
5 192.168.255.105 192.168.255.205 120 CPE5G_5G120 zllinkcpe123456120
6 192.168.255.106 192.168.255.206 124 CPE5G_5G124 zllinkcpe123456124
7 192.168.255.107 192.168.255.207 128 CPE5G_5G128 zllinkcpe123456128
8 192.168.255.108 192.168.255.208 132 CPE5G_5G132 zllinkcpe123456132
9 192.168.255.109 192.168.255.209 136 CPE5G_5G136 zllinkcpe123456136
A 192.168.255.110 192.168.255.210 140 CPE5G_5G140 zllinkcpe123456140
B 192.168.255.111 192.168.255.211 149 CPE5G_5G149 zllinkcpe123456149
C 192.168.255.112 192.168.255.212 153 CPE5G_5G153 zllinkcpe123456153
D 192.168.255.113 192.168.255.213 157 CPE5G_5G157 zllinkcpe123456157
E 192.168.255.114 192.168.255.214 161 CPE5G_5G161 zllinkcpe123456161
F 192.168.255.115 192.168.255.215 165 CPE5G_5G165 zllinkcpe123456165

Troubleshooting

Trouble Reason Solution
Packet Latency
  1. Wireless interference
  2. Distance is too long, or there are some walls between them
  3. CPE’s angle in the wrong direction, weak signal

|

  1. Use WiFi analysis to choose the best channel
  2. CPE should be in the normal distance, and avoid the wall
  3. Adjust the angle of CPE according to signal strength

Wrong Password|

  1. Forget the password
  2. Input wrong password
  3. Too much cookie
  4. WiFi password is confused with the WEB access password

|

  1. Press the “RST” button in 10s to reset the bridge, the default password is admin.
  2. Re-input the password
  3. Clear cookie, run arp-d to clear MAC table
  4. WEB access user name and password is “admin”

Can not login WEB|

  1. Local IP is not in the same network segment of CPE
  2. IP is taken by other devices
  3. LAN connection or ethernet cable has a problem
  4. Too much cookie, MAC address haven’t update

|

  1. Ping bridge IP address to see the connection status
  2. Stop other devices or change to another IP address
  3. Check LAN connection and Ethernet cable
  4. Clear cookie, run arp -d to clear MAC address

System LED light off|

  1. PoE power supply is not working
  2. Some problem in CPE’s PoE port
  3. Ethernet cable is loose, RJ45 port is wrong power current/ voltage lower or wrong

|

  1. Check if the PoE adapter or PoE switch work
  2. Check if the PoE port of CPE is ok
  3. Check if Ethernet cable is loose if Ethernet cable plugged into PoE port
  4. Check if the voltage is normal, if the socket has problem if the input voltage of the PoE adapter is normal

Low transmission Rate|

  1. Packet Latency
  2. Ethernet cable circuit
  3. Network virus attack
  4. Too much access users
  5. Network Cables type lower than Cat 5e?

|

  1. Adjust the distance, angle and channel to decrease latency
  2. Check if port isolated to avoid network virus and broadcast storm
  3. Decrease the access users.
  4. Use Cat 5e or above network cable.

Device always dead|

  1. Static electricity
  2. Running time too long
  3. Lightning stroke

|

  1. Make CPE or PoE adapter need a ground connection
  2. Running time over 7 days, reboot it
  3. After lightning, device PoE port broken or unstable better to deploy lightning conductor

Technical Support and Service

A. Thank you for your order and for using ULNA Wireless Bridge, please read the manual carefully before use. If there are any problems during the use, please contact us in time;
B. The installation of this device requires some network knowledge. If you can’t install it, please let us know or contact a professional. (There are also many installation videos of the bridge on the YouTube that you can refer to)
Tech Service Email : support01@ulnastore.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals