ULNA CP4B0103US Point to Point Wireless Bridge User Manual

June 14, 2024
ULNA

ULNA Logo WIRELESS BRIDGE
— USER MANUAL —

CP4B0103US Point to Point Wireless Bridge

ULNA CP4B0103US Point to Point Wireless Bridge Model: CPE609P

Tips:
Thank you for ordering and using ULNA CPE609P Wireless Bridge, please read the manual carefully before use. If there are any problems during the use, please contact us in time.
(Reference connection setup video: You can search for ULNA wireless bridge on Hardy Brothers Product Reviews channel on YouTube.)
The installation of this device requires some network knowledge. If you cant install it, please let us Know or contact a professional.
Customer Service Email: support01@ulnastore.com

Overview

1.1 Introduce
ULNA CPE609P is a long-distance 5.8G wireless transmission device with dual gigabit ports. It uses wireless communication technology to transmit network data using air as a medium to perform long-distance point to point or point to multi-point interconnection. The working data link layer realizes the interconnection of local area networks. The transmission distance can reach up to 5KM/3.1Miles.
CPE609P Video Bridge Transmission usually consists of two devices in AP and Client mode respectively. On the Client-side (Receiver) CPE connects with IP Camera, at the AP side (Transmitter) CPE connects with a video recorder. The AP can be receiving wireless data transmitted from multiple Clients, and it is easy and convenient to centralized management of the remote equipment.
CPE is widely used in highways, reservoir river monitoring, elevator onitoring systems, site crane monitoring systems, port terminal monitoring systems, marine aquaculture monitoring systems, and so on.
Point to point extend network WiFi range, extend the network in the house to your barn, garage, church, warehouse, and even neighbor’s house through wireless bridge signal transmission. No need to install a new modem and pay for it every month, saving you money.

1.2 Highlights

  1. Transmission using 5.8Ghz wireless technology ;
  2. Dual IOOOMbps RJ45 LAN port, support Gigabit;
  3. Built-in 14dbi high gain WiFi antenna;
  4. Support IEEE802.1lac and compatible with IEEE 802.1la/an;
  5. Transmission distance up to 5km (Barrier-Free), line of sight;
  6. Master bridge supports WiFi hotspot access;
  7. Dialing to set the transmitter (Master bridge) and receiver (Slave bridge), easy to use;
  8. WDS networking mode, video network dual compatible;
  9. Support point to point, point to multi-point mode;
  10. Support 24V PoE power supply, easy to install and deploy;
  11. Support WEB GUI access management device.

1.3. Specifications

Brand ULNA
Model CPE-609P
CPU MT7621A+MT7612EN
Flash 8MByte
DRAM DDR2 128MByte
Interface Dual 1000Mbps Ports
Data rate Ila: 54M, 48M, 36M, 24M, 18M, 12M, 9M, 6Mbps lln: 7.2M,14.4M,

21.7M, 28.9M, 43.3M, 57.8M, 65M, 72.2M, 14.4M, 28.9M, 43.3M, 57.8M, 86.7M, 115.6M, 130M, 144.4Mbps 433Mbps, Max 1000Mbps
Transfer method| IEEE802.11ac IEEE 802.11a/an
Frequency Range| 5.8GHz, 5180MHz -5825MHz
Power| 18W, PoE 24V-1A; 12V-1A
Antenna| 14dBi, Horizontal 60°/Vertical 30°
WEP GUI| Support
Telnet| Support
Serial| Support
Safety| WPA-Personal, WPA2-Personal, WPA-Auto-Personal,
WPA-Enterprise (Radius), WPA2-Enterprise(Radius), WPA-Auto-Enterprise(Radius), Radius with 802.1x
Temperature| -30∼65°C

Package Included

  • 2 x CPE609P Wireless Bridge
  • 2 x Gigabit PoE Injector (24v)
  • 2 x Cat be Network Cable
  • 2 x Metal Hoop
  • 1 x Mounting Screw Set
  • 1 x User Manual

ULNA CP4B0103US Point to Point Wireless Bridge - Package
Included

Interface Details

ULNA CP4B0103US Point to Point Wireless Bridge - Digital
Tube

3.1. Button Operation
Reset Button: Long press for 10S to reset the wireless bridge; Short press to toggle a different character to pairing.
A-B Button: Pushing the button to ‘A’ indicates that the bridge acts as the master bridge (transmitter), and pushing the button to “B” indicates that the bridge acts as the slave bridge (receiver).

LED Indicator Details

ULNA CP4B0103US Point to Point Wireless Bridge - LED

LED Light Description
Signal Lights After the bridge is connected successfully, the WLAN light will

be on, otherwise the WLAN light will not be lit.
LAN1/LAN2| The data connection is successful, the LED light is on, otherwise, it is not bright.
PWR| Power indicator, the LED is on after plug in
Digital Tube| Digital display LED flashing means editing the configuration or connecting
Digital Tube| A fixed number means that the bridges are paired successfully and are working.
The Small Red Dot|
Successfully Pairing|

Quick Start

5.1 POE Power Supply
The CPE609P wireless bridge adopts a PoE power supply, which is easy to install and manage while saving costs.ULNA CP4B0103US Point to Point
Wireless Bridge - Power Supply

1.1.1 According to the requirements, prepare a long enough network cable (Recommended within 65 meters, must be Cat 5e or above) to connect the wireless bridge and the PoE injector. The PoE port of the PoE injector is connected to one of the LAN port of the wireless bridges.
1.1.2 The other LAN port of the wireless bridges is connected to the PC, router, and switch…ULNA CP4B0103US Point to Point Wireless Bridge - Power
Supply 1

1.1.3 You can also connect the PoE port of the PoE injector to the wireless bridge, LAN port of PoE to the the PC, router, and switch…..

5.2 Point to Point Pairing Step:

  1. Switch one unit to A(Master Bridge) and the other one to B(Slave Bridge);
  2. Connect the PoE to each unit by the Ethernet cable and plug in;
  3. Wait for them to power up, about 2 min;
  4. Short press the reset button to select the channel from 1 to F;
  5. Repeat the above steps for the other bridge. Both of the 2 bridges need to be on the same channel;
  6. Wait for 2-5 minutes to complete the pairing. When the number of the digital tube is fixed and the signal light on the side turns on, it means the pairing is successful;
  7. Finally connect other devices (Router, PC, Switch) and install them to the target location.
    (TIPS: Steps 1, 4 and 5 are already Pre-configured)

5.3 Point to Multi-point Pairing Step:
e.g.
1 Master bridge and 3 Slave Bridges

  1. Switch one unit to A(Master Bridge) and the other 3 units to B (Slave Bridge):
  2. Connect the PoE to each unit by the Ethernet cable and plug in;
  3. Wait for them to power up, about 2 min;
  4. Short press the reset button to select the channel from 1 to F;
  5. Repeat the above steps for the other 3 bridges. All of the 4 bridges need to be on the same channel;
  6. Wait for 2-5 minutes to complete the pairing. When the number of the digital tube is fixed and the signal light on the side turns on, it means they pairing is successful;
  7. Finally connect other devices (Router, PC, Switch) and install them to the target location.
    (TIPS: Steps 1, 4 and 5 are already Pre-configured)

  Note:
For point to point installation, the line of sight of the 2 wireless bridges must be clear and cannot pass through the wall. The signal transmission angle of the bridge is 60 degrees. For point to multi-point installation, the angle of the slave bridge needs to be adjusted to ensure that it is within the 60-degree signal range of the main bridge. The antenna polarization direction is horizontal 60°/vertical 30°.

Installation

6.1 Pole mountULNA CP4B0103US Point to Point Wireless Bridge - Pole
Mount 6.2 Wall-mountedULNA CP4B0103US
Point to Point Wireless Bridge - Wall mounted

6.3 Connect to the device![ULNA CP4B0103US Point to Point Wireless Bridge

  • Connect device](https://manuals.plus/wp-content/uploads/2023/11/ULNA- CP4B0103US-Point-to-Point-Wireless-Bridge-Connect-device.jpg) Choose to pole mount or wall-mounted, adjust the CPE orientation, the bracket is not included in the package. Recommended ULNA Universal Bracket (ASIN: BOBCNZFNTD)

WIFI Function

1. The WiFi function is turned on by default for the master bridge.
WiFi SSID: 5GCPE_ 5GXXX
WiFi PWD: qlinkcpel23456XXX
XXX represents different channels, please refer to the comparison table in the user manual.
You can access the wireless bridge through your computer to set the SSID and new WiFi password. Please refer to the advanced settings section.

Application Case

8.1 Case 1: Point-to-point extended network WiFi range
Suitable for extending the network to second building, such as garages, shops, barns,etc.ULNA CP4B0103US Point to Point Wireless Bridge -
Computer 8.2 Case 2: Point-to-point extended of surveillance cameras rangeULNA CP4B0103US Point to Point
Wireless Bridge - IP Camera 8.3 Case 3: Point-to-multiple point extended surveillance cameras rangeULNA CP4B0103US
Point to Point Wireless Bridge - IP Camera 1 8.4 Case 4: Point-to-point extended surveillance cameras rangeULNA CP4B0103US Point to Point Wireless Bridge - IP Camera
2

Advanced Settings

Note:
The wireless bridge can work without advanced settings |

  1. Computer Access Wireless Bridge, connect the CPE to the computer by
    Ethernet cable Refer to the figure to connect the CPE to computer by
    Ethernet cable and power the CPE by PoE injectorULNA CP4B0103US Point to
Point Wireless Bridge - POE Charger

  2. Modify your computer’s IP address, make your computer’s IP and the bridge’s IP address be on the same network segment (LAN) so that you can access them.ULNA CP4B0103US Point to Point Wireless Bridge - IP Camera 3 Step 1: Find and open “Open Network and Sharing Center’ on your computer. Tips: click the network icon in the lower right corner of the computer.
    Step 2: Find and open the “Change adapter settings’, select “Local Area Connection to right-click to open the network properties. Refer to the picture above to open.
    Step 3: Find and double-click open the ‘Internet Protocol Version 4 (TCP/IPv4)”, choose the ” Use the following IP address” and enter IP address, subnet mask, Default gateway, Preferred DDS server.

  3. Change your computer’s IP address to 192.168.255.xxx (192.168.255.xxx cannot be the same as the IP of the CPE), then entry IP address is 192.168.255.xxx, the subnet mask is 255.255.255.0 (Autofill), the Default gateway is 192.168.255.xxx, Preferred DDS server 192.168.255.xxx. You can use 192.168.255.105 (xxx=5) in the reference picture to set.ULNA CP4B0103US Point to Point Wireless Bridge - Nwe tab

  4. On the login page
    User Name: admin
    Password: admin
    Note: 2
    “admin” is not the password of the WiFi SSID, it is just the password for WEB access.ULNA CP4B0103US Point to Point Wireless Bridge - Admin
Login

  5. Login successful, go to setting.
    5.1 Language – ULNA Wireless Bridge CPE609P support English&Chinese, you can choose the language on this pageULNA CP4B0103US Point to Point Wireless
Bridge - Setting5.2 Digit on/off
    Digit on/off’ Enable – the bridges are pairing by switching the A-B button and short click the reset button to select a channel:
    Digit on/off” Disable – the bridges are pairing by manually selecting a channel and A/B bridge on the Web page.
    5.2.1 Disable Digit on/off’ – Selecting Master/Slave BridgeULNA CP4B0103US
Point to Point Wireless Bridge - Disable5.2.2 Disable Digit on/off’ – Selecting a channelULNA CP4B0103US
Point to Point Wireless Bridge - Disable Digit5.3 Watchdog – You can enable or disable watchdog function on this pageULNA CP4B0103US Point to Point Wireless Bridge -
Watchdog5.4 Wireless 5Ghz
    5.4.1 Channel Bandwidth – The wider bandwidth, the shorter transmission distance. We recommend you to select the maximum bandwidth.ULNA CP4B0103US
Point to Point Wireless Bridge - Channel Bandwidth5.4.2 Region Code – Please select the right time zone of the wireless bridge on this page, which affects the WiFi speed.ULNA
CP4B0103US Point to Point Wireless Bridge - Channel Bandwidth
15.4.3 SSID & Password – You can find the WiFi information on this pageULNA CP4B0103US Point to Point
Wireless Bridge - SSID & Passwrrd Note:
    If you want to set a new SSID and password, just enter new information and apply.
    5.4.4 If you have changed the SSID and password, you could enter the new information on the page for faster automatic re- pairing.5.5 How to change IP address- You can change the IP address on this page.ULNA CP4B0103US Point to
Point Wireless Bridge - IP Address5.6 System LogULNA CP4B0103US Point to Point Wireless Bridge -
Systam Log5.7 How to Change Login User Name and Password
    Enter the new information on Administrator Login, New Password, Retype Password and then Apply.ULNA CP4B0103US Point to Point Wireless Bridge -
Systam Log 1

Digital & IP & WiFi Correspondence Chart
You can check the SSID and password through this chart.

LED A IP B IP 5.8 ID SSID Password
0 192.168.255.100 192.168.255.200 0 5GCPE_5G0 alinkcpe1234560
1 192.168.255.101 192.168.255.201 36 5GCPE_5G36 ci11nkcpe12345636
2 192.168.255.102 192.168.255.202 64 5GCPE_5G64 ci11nkcpe12345664
3 192.168.255.103 192.168.255.203 100 500PE_50100 ci11nkcpe123456100
4 192.168.255.104 192.168.255.204 48 5GCPE_5G48 a11nkcpe12345648
5 192.168.255.105 192.168.255.205 120 500PE_50120 ci11nkcpe123456120
6 192.168.255.106 192.168.255.206 124 500PE_50124 ci11nkcpe123456124
7 192.168.255.107 192.168.255.207 128 5GCPE_50128 ci11nkcpe123456128
8 192.168.255.108 192.168.255.208 132 5GCPE_5G132 ci11nkcpe123456132
9 192.168.255.109 192.168.255.209 136 500PE_5G136 ci11nkcpe123456136
a 192.168.255.110 192.168.255.210 112 5GCPE_5G112 ci11nkcpe123456112
b 192.168.255.111 192.168.255.211 149 5GCPE_5G149 ci11nkcpe123456149
c 192.168.255.112 192.168.255.212 153 5GCPE_5G153 ci11nkcpe123456153
D 192.168.255.113 192.168.255.213 157 5GCPE_5G157 ci11nkcpe123456157
e 192.168.255.114 192.168.255.214 116 5GCPE_5G116 a11nkcpe123456116
f 192.168.255.115 192.168.255.215 108 5GCPE_5G108 cilinkcpe123456108 1

Troubleshooting

Trouble Reason Solution
Packet Latency 1. Wireless interference

2. Distance is too long, or there are some walls between them
3. CPE’s angle in the wrong direction, weak signal| 1. Use WiFi analysis to choose the best channel
2. CPE should be in the normal distance, and avoid the wall
3. Adjust the angle of CPE according to signal strength
Wrong Password| 1. Forget the password
2. Input wrong password
3. Too much cookie
4. WiFi password is confused with the WEB access password| 1. Press the “RST” button in lOs to reset the bridge, the default password is admin.
2. Re-input the password
3. Clear cookie, run arp -d to clear MAC table
4. WEB access user namer and password is “admin”
Can not login WEB| 1. Local IP is not in the same network segment of CPE
2. IP is taken by other devices
3. LAN connection or Ethernet cable has a problem
4. Too much cookie, MAC address haven’t update| 1. Ping bridge IP address to see the connection status
2. Stop other devices or change to another IP address
3. Check LAN connection and Ethernet cable
4. Clear cookie, run arp -d to clear MAC address
System LED light off| 1. PoE power supply is not working
2. Some problem in CPE’s PoE port
3. Ethernet cable is loose, RJ45 port is wrong power current/voltage lower or wrong| 1. Check if the PoE injector or PoE switch work
2. Check if the PoE port of CPE is ok
3. Check if Ethernet cable is loose if Ethernet cable plugged into PoE port
4. Check if the voltage is normal, if the socket has problem if the input voltage of the PoE injector is normal
Low transmission Rate| 1. Packet Latency
2. Ethernet cable circuit
3. Network virus attack
4. Too much access users
5. Network Cables type lower than Cat Se?| 1. Adjust the distance, angle and channel to decrease latency
2. Check if port isolated to avoid network virus and broadcast storm
4. Decrease the access users.
5. Change use a Cat 5e or above network cable.
Device always dead| 1. Static electricity
2. Running time too long
3. Lightning stroke| 1. Make CPE or PoE injector need a ground connection
2. Running time over 7 days, reboot it
3. After lightning, device PoE port broken or unstable better to deploy lightning conductor
Received defective bridge| Transport damage| Contact us to get a new replacement
Will not pass internet traffic| 1. Wrong way to use 2.Need to upgrade the firmware| 1. Make sure the bridges have been Pairing;
2. Make sure the 2 bridges are installed face to face, with a clear line of sight and no obstructions;
3. The slave bridge can’t transmit WiFi, just connect the bridge and a computer by Ethernet cable to try to see if there is a network. and if you want to connect it wireless, then connect the slave bridge to a new router;
4. Upgrade the firmware.
One of the bridge doesnt work| 1. The PoE is defective
2. This bridge is defective| Please change the other PoE to charge.
1. If it works, it’s the problem of the PoE. Contact us to replac the PoE.
2. If it doesn’t work, it’s the problem of the bridge. Contact us to replace the bridge.

Technical Support and Service

A. Thank you for your order and for using ULNA Wireless Bridge, please read the manual carefully before use. If there are any problems during the use, please contact us in time;
B. The installation of this device requires some network knowledge. If you cant install it, please let us know or contact a professional. (There are also many installation videos of the bridge on the YouTube that you can refer to, Reference connection setup video:  You can search for ULNA wireless bridge on Hardy Brothers Product Reviews channel on YouTube.)

Tech Service Email:support01@ulnastore.com

ULNA Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals