MOUNTUP ZDT10-C01-US2 Monitor Stand for Desk Installation Guide

MOUNTUP ZDT10-C01-US2 Monitor Stand for Desk

Product Information

• Specifications:
  • Product Dimensions: 6.5mm/0.26
  • Rotation: 115mm, 100mm, 75mm / 4.53, 4, 3
  • Max Height: 361mm/14.21
  • Min Height: 186mm/7.32
  • Tilt: 35mm/1.38
  • Swivel: 300mm/11.81

Product Usage Instructions

• Step 1: Support Pillar Installation
  • Attach MA x4, MB x4, MC x4, and MD x4 to the support pillar.
• Step 2: Apply Foot Pads to the Base
  • Place the base on the table.
  • Attach washers (B) and bolts (A) to the base.
  • Position the support pillar with clip holes facing backwards and place it under the base.
  • Tighten the bolts (A) using a 4mm allen key (G).
  • Remove the plastic film from the foot pads (F) and attach them to the four corners of the base bottom.
• Step 3: Attach the Plate Component to the Monitor
  • Select Monitor Screw Length
  • When attaching the plate to the flat screen, be careful not to over-tighten screws and ensure that screws do not bottom out in the mounting holes.
  • Too Short: Use shorter screws (MA).
  • Too Long: Use longer screws (MB, MC, MD).
• Attach the Plate Component
  • For Flat Back Monitor:
  • Use the shorter screws (MA) to attach the plate component.
  • If the MA screw is too long, use a H5mm spacer (M-H) to fix it.
  • For Recessed/Curved Back Monitor:
  • Use the long screws (MB) to attach the plate component.
• Step 4: Attach Monitor with Plate Component to Pillar
  • Choose the appropriate position for your monitors and hang them onto the support pillar.
  • Ensure that the ARROW mark on the plate component is pointing upwards.
• Step 5: Cable Management
  • Attach wire clips (E) into the holes of the support pillar and use them to manage cables.
• Step 6: Adjustments (If necessary)
  • Tilt Adjustment
  • Slightly loosen the tilting bolt with the Allen Key (H).
  • Hold the monitor with both hands and adjust it to your desired tilt angle.
  • Retighten the tilting bolt to secure the monitor in place.
  • Leveling Adjustment
  • Tighten the levelling adjustment for stability.
  • Swivel Adjustment
  • Rotate the monitor towards the front and tighten it with the handle bolt (C).
• FAQ:
  • Q: What should I do if I have questions or issues with the product?
  • A: Please contact our customer service for assistance before returning the product.

Safety Caution

BEFORE ASSEMBLY

• Layout all components and hardware. Check all parts are included and undamaged.
• Should anybody intend to install or use this monitor stand, please read and understand this manual carefully.
• If you do not understand these instructions or have any doubt about the safety instructions, assembly or use of this product, please contact our customer service.

WARNING

• This product contains small items that could be a choking hazard if swallowed.
• KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
• Improper installation, such as using the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury.
• We would not be liable for any damage or injury caused by improper mounting or inappropriate use.

CAUTION AND MAINTENANCE

• Never allow children to climb, stand, hang, or play on any part of the monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Installation Tools

Installation Tools (Not Included)

Parts and Hardware

Supplied Parts and Hardware

Hardware

Hardware (Product)

Hardware (Monitor)

NOTE: Not all hardware included will be used.

Product Dimensions

• STEP 1: Support Pillar Installation
  • Put Base on the table; put Washers (B) and Bolts (A) on the base; keep clip holes of 3 Support Pillar toward backside then put Plastic Cover (D) and Support Pillar under the base. Then tighten the bolts (A) with the 4mm allen key (G).
• STEP 2: Apply Foot Pads to the Base
  • Hold the Support Pillar with one hand and tear off plastic film of Foot Pads (F), then attach Foot Pads (F) near four conors of the Base 1 bottom.
• STEP 3: Attach the Plate Component to Monitor
  • 3-1 Select Monitor Screw Length
  • When attaching the plate to the flat screen, be careful not to over-tighten screws and be sure that screws do not bottom out in the mounting holes.
  • 3-2 Attach the Plate Component
• STEP 4: Attach Monitor with Plate Component to Pillar
  • Choose the appropriate position for your monitors, and hang the monitors onto the Support Pillar.
• STEP 5: Cable Management
  • Attach Wire Clips (E) into the holes of Support Pillar. Manage cables with the Wire Clips (E).
• STEP 6: Adjustments (If necessary)
  • Tilt Adjustment
  • Slightly loosen the tilting bolt with the Allen Key(H).
  • Hold the monitor with both hands and adjust the monitor to your desired tilt angle.
  • Retighten the tilting bolt to secure the monitor in place.
  • Leveling Adjustment
  • Swivel Adjustment

INFORMATION

If you have any questions, please feel free to contact Customer Service via Amazon before returning. (ZDT10-C01-US2)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>