ARROW 16GA Flooring Nailer and Stapler Instruction Manual

16GA Flooring Nailer and Stapler

Product Information

The product is a flooring stapler and cleat nailer designed for
installing 1 1/2 – 2 inch M (38 – 50 mm) flooring. It can be used
with flooring staples, L-cleats, and T-cleats.

• Flooring Staples: 15.5GA, available in 1-1/2, 1-3/4, and 2 inch
  (38mm, 45mm, and 50mm) lengths

• L-Cleats: 16GA, available in 1-1/2, 1-3/4, and 2 inch (38mm,
  45mm, and 50mm) lengths

• T-Cleats: 16GA, available in 1-1/2, 1-3/4, and 2 inch (38mm,
  45mm, and 50mm) lengths

Product Usage Instructions

1. Assembly

1. Attach the hammer face to the base using the provided hex
   bolts.

2. Secure the washer and shaft sleeve to the cylinder cover using
   hex bolts.

3. Attach the bumper to the pressure plate using hex bolts.

4. Connect the poppet actuator to the cylinder base.

5. Attach the piston cylinder to the body using the provided
   O-rings.

2. Loading Fasteners

1. Open the easy load magazine by pressing the button quick
   release connect.

2. Insert the flooring staples or cleats into the magazine, making
   sure they are aligned properly.

3. Close the magazine securely.

3. Adjusting Settings

1. Use the adjusting knob to set the desired depth of penetration
   for the fasteners.

2. Adjust the pressure on the regulator to ensure proper power and
   speed of shooting.

4. Operating the Flooring Stapler

1. Connect the flooring stapler to an air compressor using the
   quick connector and air hose.

2. Hold the stapler firmly with the overmold grip.

3. Position the flooring base on the desired area and press the
   trigger to shoot the fastener.

4. Move the stapler along the flooring, repeating the process
   until installation is complete.

Specifications

• Staple Size: 1 1/2 – 2 inch (38 – 50 mm)
• Cleat Size: 1 1/2 – 2 inch (38 – 50 mm)
• Gauge: 15.5GA (Staples), 16GA (L-Cleats and T-Cleats)

FAQ

Problem: Air leaking in Cylinder Cover

Cause:
A. Loose poppet actuator screws.
B. Cracked or worn O-ring.

Solution:
A. Tighten the screws and recheck.
B. Replace the O-ring.

Problem: Lack of power, slow to cycle

Cause:
A. Tool is too dry.
B. Air pressure is too low.
C. Exhaust is blocked.

Solution:
A. Apply lubricant to the tool.
B. Check and adjust the air pressure.
C. Clean the exhaust channel.

Problem: Shooting no fastener or intermittent feeding

Cause:
A. Damaged coil spring.
B. Wrong size of fastener.
C. Magazine or drive guide is dirty.

Solution:
A. Replace the coil spring.
B. Use the correct size of fastener.
C. Clean the magazine and drive guide.

1 1/2″ -2″ 38 – 50 mm FLOORING
STAPLE
1 1/2″ -2″ 38 – 50mm L FLOORING
CLEAT
1 1/2″ -2″ 38 – 50mm T FLOORING
CLEAT

15.5GA
FLOORING STAPLES

1-1/2″ 1-3/4″ 2″

38mm 45mm 50mm

16GA
L-CLEATS

1-1/2″ 1-3/4″ 2″

38mm 45mm 50mm

16GA
T-CLEATS

1-1/2″ 1-3/4″ 2″

38mm 45mm 50mm

Quick Connector
Quick Coupler

Quick Connector

Filert

Air Hose

Quick Coupler
Regulator

AIR Compressor

2 1

Overmold Grip
Button Quick Release Connect

Hammer Face

Easy Load Magazine
Adjusting Knob

Flooring Base

Quick Moving Roller

PART DESCRIPTION QTY PART DESCRIPTION QTY PART DESCRIPTION QTY PART DESCRIPTION QTY

1 Hammer Face 1 20

Base

1 39 Hex Bolt M5X6 4 58 Magazine End Stopper 1

2 Hex Bolt M5X25 4 21

Pin

2 40 Adjusting Base 1 59

Spring

1

3

Washer 5

4 22

Washer 8

2 41 Support Plate 2 60

Pin

1

4 Cylinder Cover 1 23 Shaft Sleeve

2 42 Hex Bolt M5X10 4 61 Coil Spring

1

5 Hex Bolt M4X20 3 24 Hex Bolt M6X40 4 43

Bumper

2 62 Hex Bolt M4X4

6 Poppet Actuator 1 25

Washer 6

12 44

Spring

4 63

Pusher

1

7 O-ring 46.2X2.65 1 26 Pressure Plate

1 45

Hex Bolt

4 64

Plug Cap

1

8 O-ring 54.2X3.5 1 27

Washer 4

4 46 Hex Bolt M5X10 4 65

Gasket

1

9

Piston Cap

1 28 Hex Bolt M4X10 4 47 Spring Pin 3X8 1 66 End Cap component 1

10 O-ring 15.9X1.8 1 29

Plate

1 48 Drive Guide Cover 1 67 Hex Bolt M6X25 6

11 O-ring 17.5X2.6 1 30

Roller

2 49

Spring

1 68

Button

1

12 Piston Cylinder 1 31 Roller Shaft

2 50 Limited Nail Plate 1 69 Button Spring 1

13 O-ring 13.5X2.6 1 32

E rings 5

4 51 Hex Bolt M4X16 1 70 O-ring 36.5X3.5 1

14 O-ring 19.2X1.8 1 33

Shaft

1 52 Hex Bolt M6X20 2 71 Spline Housing 1

15

Firing Pin

1 34

Gear

3 53 Drive Guide

1 72 Spline Shaft

1

16 O-ring 57.4X3.5 1 35 Adjust Shaft

1 54 Hex Bolt M5X20 2 73 Hex Bolt M5X12 1

17

Body

1 36 Adjusting Knob 1 55 Spring Pin 3X20 1 74

Handle

1

18

Bumper

1 37 Steel Balls 3

1 56

Magazine

1 75

Hammer

1

19 Cylinder Base 1 38

Spring

1 57 Circlips For Shart 1

PROBLEM

CAUSE

SOLUTION

Air leaking in Cylinder A. Loose poppet actuator screws.

Cover

B. O-ring is cracked/worn.

A. Tighten and recheck. B. Replace o-ring.

Lack of power,slow to cycle. Poor power of shooting and returning.

A. Tool is too dry. B. Air pressure too low. C. Exhaust blocked.

A. Drop lubricant. B. Check air supply equipment. C. Clean exhaust channel.

Shooting no fastener or intermittent feeding.

A. Damaged coil spring. B. Wrong size of fastener. C. Magazine or drive guide is dirty

A. Replace spring. B. Use standard fasteners. C. Clean magazine and drive guide.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>