ELITE SCREENS SAKER SERIES Projector Screens Instruction Manual

SAKER SERIES Projector Screens
Instruction Manual

Section 1: Screen Design

1.1 What is it for?
The Saker Series is an electric projection screen that embodies all the virtues of quality, durability, and aesthetic value. It utilizes our MaxWhite™ Fiberglass (FG) material which has a wide viewing angle to allow the audience to see the image from anywhere in the room. Standard features include a wireless 5-12 volt trigger, IR/RF remotes control package, and a detachable manual keypad switch.
1.2 How does it work?
The enameled aluminum casing has a stylish are curate profile that is best suited to the aesthetics of interior design. To make installation easy, the Saker comes fully assembled with sliding wall mounts to ensure that it will be properly centered in every installation.

Section 2: Control System

2.1 Wireless 5-12 Volt Trigger Cable
A wireless 5-12 volt projector trigger automatically drops/rises your screen when your projector is turned on/off. Eliminates the need to wire the connection from your projector to the screen for a clean installation
2.2 IR Remote
The infrared remote control requires direct line of sight and works up to 30 feet.
2.3 RF Remote
The radio frequency remote control does not require line of sight and works up to 100 feet.
2.4 3-Way Wall Switch
The 3-Way Wall Switch is a detachable switch that connects to the R145 port.
Section 2: Product Features
2.1 Characteristics Screen Material

• MaxWhite™ Fiberglass (1.1 Gain) matte white fiberglass-backed material
• Wide viewing angle and uniformly diffuses light in all directions
• Active 3D and 4K Ultra HD Ready
• Standard black masking borders and black screen backing
• Flame Retardant: Complies with NFPA 701 standards Elite Screens Inc.

Control System

• Internal Radio Frequency/Infrared receivers with IR, RF remotes included
• Detachable 3-way wall switch keypad for UP/STOP/DOWN manual operation
• Wireless 5-12 volt trigger included
• RJ45 port allows 3rd party control system integration

Design and Installation

• Arcuate profile aluminum enamel white case with parallel grooves
• Mounting hardware kit included for wall or ceiling installations
• Extra top black masking border for high ceiling installations
• Flush hidden wall mounts allow screen to slide horizontally for proper centering
• Plug & Play ready, no hardwired installation required

Quality and Reliability

• Synchronous motor has silent operation and low power consumption
• GREEN GUARD® and GREEN GUARD® Gold (UL 2818) Certified for indoor air quality emissions

2.2 Certifications

2.3 Model Numbers

Model Number

| Diag. Size| Aspect Ratio| Viewing Height (in)| Viewing Width (in)| Screen Material| Gain| Case Color| N.W. (lbs)| G.W. (lbs)| Packaging Dimensions (LxWxH)
---|---|---|---|---|---|---|---|---|---|---
SK84XHW-E24| 84″| 16:9| 41.2| 73.2| MaxWhite™ FG| 1.1| White| 22.4| 30.2| 90.7″x 6.3″x 6.9″
SK100XHW-E24| 100″| 16:9| 49.0| 87.2| MaxWhite™ FG| 1.1| White| 26.3| 34.7| 106.6″x 6.3″x 6.7″
SK110XHW-E24| 110″| 16:9| 53.9| 95.9| MaxWhite™ FG| 1.1| White| 29.5| 38.9| 114.3″x 6.3″x 6.7″
SK120XHW-E20| 120″| 16:9| 58.8| 104.6| MaxWhite™ FG| 1.1| White| 31.8| 41.2| 122.3″x 6.3″x 6.7″
SK135XHW-E18| 135″| 16:9| 66.2| 117.7| MaxWhite™ FG| 1.1| White| 34.9| 44.3| 137.2″x 6.3″x 6.7″
SK150XHW-E12| 150″| 16:9| 73.5| 130.7| MaxWhite™ FG| 1.1| White| 50.4| 66.9| 148.4″x 7.9″x 8.5″
SK100NXW-E24| 100″| 16:10| 53.0| 84.8| MaxWhite™ FG| 1.1| White| 29.2| 34.6| 105.1″x 6.3″x 6.7″
SK120NXW-E12| 120″| 16:10| 63.6| 101.8| MaxWhite™ FG| 1.1| White| 31.2| 40.3| 121.3″x 6.3″x 6.7″
SK180XVW2-E4| 180″| 4:3| 108.0| 144.0| MaxWhite™ FG| 1.1| White| 57.9| 75.7| 160″x 7.9″x 8.6″
SK180XHW2-E12| 180″| 16:9| 88.3| 156.9| MaxWhite™ FG| 1.1| White| 60.7| 79.5| 174.4″x 7.9″x 8.6″

Section 3: Screen Material Specifications

3.1 Characteristics
MaxWhite™ Fiberglass (FG) is fiberglass backed for added stiffness which provides the flattest possible non-tensioned screen surface with universal applications. This material provides wide viewing uniform diffusion while giving precise definition, color reproduction and black & white contrast. The screen surface has a black-backing to eliminate light penetration, is mildew resistant and washable with mild soap and water.

* Manufacturer tip: This is an enhanced matte white product for higher end DLP/LCD projectors suitable for commercial and residential presentations.

Features & Benefits

• Multi-layer weave with textured surface
• Fiberglass backing with black backing
• Gain: 1.1
• View Angle: 180° (90° ± LR)
• Mildew Resistant
• Active 3D and 4K Ultra HD ready
• Surface can be cleaned with mild soap and water
• Flame Retardant: Complies with NFPA 701 Standards
• GREENGUARD® and GREENGUARD® Gold Certified I UL 2818

Specifications|
---|---
Thickness| 0.36 mm
Weight| 350 g/m2
Maximum Height| 3.2 M (10 ft)
On-axis Gain| 1.0
Half-Gain Angle| Does not reach half gain

3.2 Gain Chart

Section 4: Execution

4.1 Important Safety & Warning Precautions
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved changes or modifications (except for cutting the power cord for hardware installations) to this unit are prohibited and will void your warranty. For more information, please contact our Technical Support Department at 877-511-1211 Ext. 604.

• Please retain this user’s guide for future reference.
• To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the manufacturer.
• Handle the unit carefully during transportation to avoid any damages.
• To ensure safe and reliable operation, direct connection to a properly grounded power source is advised.
• The power outlet supplying power to the unit should be close to the unit and easily accessible.
• Do not install the unit on uneven or inclined surfaces.
• Do not put heavy objects on the power cord and position it properly to avoid creating a trip obstacle.
• Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short circuit.
• There am not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself. No one except authorized technicians can open and make repairs to this unit.
• Make sure the power source this unit is connected to has a continuous power flow.
• If them is need to use an extension cord, make sum the cord has an equal rating as the appliance to avoid overheat.
• Do not handle the power plug when your hands are wet or your feet are in contact with water.

Do not use this unit under the following circumstances.

• Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.
• Avoid direct Sunshine, rain shower and moisture.
• Keep away from fire sources and high temperature to prevent this device from overheating.
• Cut off the power supply first before transportation or maintenance.
• Fully disconnect from the power supply when the unit is not in use for a long period of time, as should be done with any other electric household appliance.
• To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is obvious damage or if there am any evident broken parts.

WARNING: The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black drop in the roller. Please be aware of this as it will void the limitation of your warranty.
Individual modifications to this product are prohibited and will void the warranty with the manufacturer. Please contact Elite Screens Customer Service for any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
✓ Reorient or relocate the receiving antenna of the device which may be causing the interference.
✓ Increase the separation between the screen and the device’s receiver.
✓ Connect the equipment into a different power outlet other than the device.

4.2 Pre-Installation

1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign particles such as dust, sawdust, and/or liquids.

NOTE: Regardless of the mounting method, the screen should be securely supported so that the vibration or pulling on the viewing surface will not cause the casing to become loose or fall. Included mounting screws are complimentary and may not be appropriate for all mounting surfaces. Use appropriate anchors to safely secure the screen to the mounting surface or consult with a professional installer.
4.3 Hardware Parts List
Please make sure all parts listed below are included before proceeding with the installation.
4.4 Installation Instructions
For installation assistance, please consult a professional Installer. Elite Screens is not liable for faulty installations.
A. Wall Mount
I. Flush mount with wall/ceiling brackets

1. Begin by sliding the bracket connector (D) all the way to each end of the housing.
2. Then attach it to the wall/ceiling mount bracket (A) with the M5 x 11 bolt screw (E).
3. Measure and mark the (W x H) distance between the two holes on each bracket.
4. Drill a hole for each screw hole on the marked areas.
5. Insert a dry-wall anchor (C) into the wall.
6. Insert aM5 x 60 Screw (B) in each thy-wall anchor (C) and screw it in leaving about 1/8″ of an inch.
7. Hang the screen by aligning the end can holes to the M5 x 60 screws (B).

II. Flush hidden mount (movable position
This mount method allows the screen to slide horizontally.

1. Determine where the screen will be installed. Then, measure and mark the distance between the top and bottom screw holes from each hidden wall mount bracket (H).
2. Drill a hole on all marked areas and install the brackets with the dry-wall anchor(C), M5 x 60 screw (B), and a washer (I). Make sure both brackets are properly leveled.
3. Hang the screen by placing the downward “catch” located on the back over the brackets upper “catch”.
4. After making sure the screen is secured, you can slide it left / right to properly center it in position.
5. Lastly, screw the MS screw (F) into the upper hole of the bracket to add additional support for the screen.

B. Ceiling Mount
I. Ceiling Mount (fixed position on end caps)

NOTE: The brackets do not slide. They are designed to attach the end caps only.

1. Attach the Wall/Ceiling mount bracket (A) to the Bracket connector (D) located on top of the screen’s housing (preinstalled).
2. Determine where the screen will be installed. Then, measure and mark the distance between the (W X H) locations.
3. Drill a hole on all marked areas and insert a thy-wall anchor(C).
4. Secure the screen by inserting the M5 x 60 screw (B) and a washer (I) thru the wall/ceiling mount brackets (A). Two or more people are required while one holds the screen in place.

II. Suspended

1. Screw the eye-bolt (G) on the bracket connector (D).
2. Attach the snap link (J) through the eye-bolt (G) and connect it to an eye-bolt screw (not included) rated for the screen’s weight.

4.5 Controls and Accessories

A. IR Remote| B. RF Remote| C. Wall switch control box| D. 5-12 volt trigger cable

E. IR extended “eye” receiver| F. Wireless 5-12v trigger cable| G. AAA batteries| H. Bubble leveller

4.6 Screen Operation
Electric Current: Depending upon region, your Elite Screen will operation 100 v, 110 v, or 220 v voltage.

1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.
2. Once the screen’s has power, you’ll be able to control it using any of the 6 methods described below.

6 ways to control your Saker

1. IR remote control (Item A, Fig 1): The Infrared functions by direct line of sight contact with a beam range of 30 feet. Aim the IR remote at the circular window located on the left side of the screen.
2. IR “Eye” Receiver (Item E, Fig 2): The IR “Eye” Receiver plugs directly into the screen’s RJ-45 input to present a low profile line-of-sight control option for your IR remote control even in a recessed ceiling installation.
3. RF Remote Control (Item B): The radio waves eliminate the need for a direct line of sight with a range of 100 feet.
4. 3-Way Wall Switch (Item C, Fig 3): The 3-way wall switch is a wall mount control box with an up/stop/down button and plugs directly into the screen’s RJ-45 input.
5. 5-12 volt trigeer (Item D, Fig 4): The built-in 5-12V trigger input allows your screen to synchronize its drop & rise with the projector’s power cycle. The screen deploys when the projector powers up and will retract when the projector powers down. The 5-12 volt 1045 cable connects to your projector’s trigger output via a separate cable that may or may not be provided by the manufacturer of the projector. The trigger feature will not work without an output cable from the projector, but it can be tested by connecting the Red (+) and Green (-) cable to a 9-volt battery.
6. Wireless 5-12 volt trigeer (Item F, Fig 5): The RF remote control serves as a dual purpose, independently as a handheld remote control, or in conjunction with the Wireless 5-12 volt trigger cable. The radio frequency technology can be programmed to send a wireless signal to synchronize its drop & rise with The projector’s power cycle.

Here’s how to set up your Wireless 5-12 volt trigeer I Synchronization Instructions
Step l: Connect one end of the 3.5 mm wireless 5-12 volt trigger cable to the RF remote.
Step 2: Connect the other 3.5 mm end of the wireless 5-12 volt trigger cable to your projector
Step 3: Make sure to unplug your screen from the power outlet
Step 4: Hold the UP button on your RF remote
Step 5: While holding the UP button, plug the screen back to the power outlet
Step 6: Wait 5 seconds and then release the UP button
Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and able to control your screen with your projector’s power cycle
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20- 30 seconds for full off and on cycle each time)

Section 5: Product Specifications

5.1 Dimensions

Model| A| A1| A2| A3| A| A5| A6| A7| B| B1| B2| B3| B4| B5| C| C1| C2| C3
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---
Unit: Inches
SK84XHW-E24| 85.7| 73.2| 85.0| 83.9| 52.4| 76.2| 79.4| 1.5| 71.8| 41.2| 67.6| 24.0| 2.4| 3.9| 4.0| 4.3| 1.4| 0.9
SK100XHW-E24| 100.7| 87.2| 99.9| 98.9| 67.4| 91.1| 94.3| 2.0| 79.6| 49.0| 75.4| 24.0| 2.4| 3.9| 4.0| 4.3| 1.4| 0.9
SK110XHW-E24| 109.6| 95.9| 108.8| 107.8| 76.3| 99.8| 103.0| 2.0| 84.6| 53.9| 80.3| 24.0| 2.4| 3.9| 4.0| 4.3| 1.4| 0.9
SK120XHW-E20| 118.1| 104.6| 117.4| 116.3| 84.8| 108.5| 111.7| 2.0| 85.4| 58.8| 81.2| 20.0| 2.4| 3.9| 4.0| 4.3| 1.4| 0.9
SK135XHW-E18| 131.2| 117.7| 130.4| 129.4| 97.9| 121.6| 124.8| 2.0| 90.8| 66.2| 86.5| 18.0| 2.4| 3.9| 4.0| 4.3| 1.4| 0.9
SK150XHW-E12| 144.3| 130.7| 143.5| 142.5| 111.0| 134.7| 137.8| 2.0| 92.2| 73.5| 87.9| 12.0| 2.4| 3.9| 4.0| 4.3| 1.4| 0.9
SK100NXW-E24| 98.3| 84.8| 97.5| 96.5| 65.0| 88.8| 92.0| 2.0| 83.6| 53.0| 79.4| 24.0| 2.4| 3.9| 4.0| 4.3| 1.4| 0.9
SK120NXW-E12| 115.3| 101.8| 114.5| 113.5| 82.0| 105.7| 108.9| 2.0| 82.2| 63.6| 78.0| 12.0| 2.4| 3.9| 4.0| 4.3| 1.4| 0.9
SK180XVW2-E4| 158.0| 144.0| 156.6| 155.2| 123.7| 148.0| 151.1| 2.0| 119.3| 108.0| 114.4| 4.0| 2.4| 4.6| 4.6| 4.9| 1.4| 0.9
SK180XHW2-E12| 171.1| 156.9| 169.6| 168.3| 136.8| 160.8| 164.0| 2.0| 107.6| 88.3| 102.6| 12.0| 2.4| 4.6| 4.6| 4.9| 1.4| 0.9
Unit: mm
SK84XHW-E24| 2178| 1860| 2158| 2132| 1332| 1936| 2016| 38| 1824| 1046| 1716| 610| 60| 100| 102| 108| 35| 23
SK100XHW-E24| 2557| 2214| 2537| 2511| 1711| 2314| 2394| 50| 2023| 1245| 1915| 610| 60| 100| 102| 108| 35| 23
SK110XHW-E24| 2783| 2435| 2763| 2737| 1937| 2535| 2615| 50| 2148| 1370| 2040| 610| 60| 100| 102| 108| 35| 23
SK120XHW-E20| 3001| 2657| 2981| 2955| 2155| 2757| 2837| 50| 2170| 1494| 2062| 508| 60| 100| 102| 108| 35| 23
SK135XHW-E18| 3332| 2989| 3312| 3286| 2486| 3089| 3169| 50| 2306| 1681| 2198| 457| 60| 100| 102| 108| 35| 23
SK150XHW-E12| 3666| 3321| 3646| 3620| 2820| 3421| 3501| 50| 2341| 1868| 2233| 305| 60| 100| 102| 108| 35| 23
SK100NXW-E24| 2497| 2154| 2477| 2451| 1651| 2256| 2336| 51| 2124| 1346| 2016| 610| 60| 100| 102| 108| 35| 23
SK120NXW-E12| 2929| 2585| 2909| 2883| 2083| 2685| 2765| 50| 2088| 1615| 1980| 305| 60| 100| 102| 108| 35| 23
SK180XVW2-E4| 4013| 3658| 3978| 3942| 3142| 3759| 3838| 51| 3030| 2743| 2906| 102| 61| 117| 117| 124| 36| 23
SK180XHW2-E12| 4346| 3985| 4308| 4275| 3475| 4084| 4166| 51| 2733| 2243| 2606| 305| 61| 117| 117| 124| 36| 23

5.2 Drawings
5.2.1 Below 180” Models

5.2.2 180” Models

5.3 Pictures
Saker Series Black and White Housing

Housing and Weight Bar Detail

Bracket Detail

RJ45 Input and IR “eye” receiver Close Up

Accessories

Section 6: About Elite Screens

6.1 Company Description
Elite Screens Inc. is a California based company that specializes in making quality commercial and home-theatre projection screens for the retail and custom install sales channels. Our company began as an innovative venture into the projection market by manufacturing veterans from the AV/IT industry. Elite Screens quickly established itself as an entry level commercial and home theatre screen manufacturer. This was accomplished by making a quality product cost effective with a focus on mass-producing screen material, sizes and aspect ratios that were most commonly preferred by AV customers in general. We focused on uniformity with what would match the mainstream demographic while including extra features that are not usually included by other manufacturers. In time, we progressed from just retail sales into the realm of custom installer/integrator manufacture as our numerous reviews and awards will attest. We stand behind our product and are so certain of customer satisfaction with the quality of our product that we offer a 2-year manufacturer’s warranty which is twice the industry standard. In our continued devotion to excellence in products and service, we are committed to implementing green practices with our production. We have adopted manufacturing methods that promote conservative regulation of our energy needs. Our simple product designs combined with the expertise of our permanent staff ensures that our entire line of products are made by experienced hands devoted to the high standards of today’s audio-video consumer.
###

http://www.www.elitescreens.com
Elite Screens Inc. I Elite Screens Europe GmbH I Elite Screens France SAS I Elite Screens India
Elite Screens China Ltd. ] Elite Screens Taiwan Corp. I Elite Screens Japan J Elite Screens Australia

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>