Arrow Storage Products CLG1014CC Arrow Classic Steel Storage Shed Owner’s Manual
- October 30, 2023
- Arrow Storage Products
Table of Contents
Owner’s Manual
& Assembly Guide
Model No.
CLG1014FG
CLG1014SG
CLG1014CC
CLG1014BG
10’ x 14’
Base 121” x 160 1/4”
Size 307,3 cm x 407,0 cm
BUILDING DIMENSIONS
- See Inside for Detailed Safety Information.
CAUTION
-
Care must be taken when handling various pieces of your building since many contain sharp edges.
-
Do NOT attempt to assemble your building before double checking that you have all the parts indicated in the parts lists.
Any building left partially assembled may be seriously damaged by even light winds. -
Keep children and pets away from the worksite during construction and until the building is completely assembled. This will help avoid distractions and any accidents which may occur.
-
NEVER concentrate your weight on the roof of the building.
-
Before assembling any parts, your base should be constructed and an anchoring system should be ready to use.
Your building MUST be anchored to prevent wind damage.
ASSEMBLY
- The best location is a level area with good drainage.
- Allow enough space outside the building to be able to access the roof with a ladder.
- Use Teamwork: Two or more people are required to assemble your building.
CARE & MAINTENANCE
- DO NOT use power washing to clean your shed.
- Combustibles and corrosives must be stored in air tight containers designed for chemical and/or combustible storage.
Corrosive chemicals such as fertilizers, pesticides and herbicides should be cleaned off the interior and exterior surfaces immediately. Rust caused by chemical damage is not covered by the warranty.
Rust protection precautions
- Avoid nicking or scraping the coating surface, inside and out.
- Keep roof, base perimeter and door free of debris.
- Touch up scrapes or nicks and any area of visible rust as soon as possible.
HARDWARE LIST
Key
No.| Part No.| Part
Description| Qty.| Part Views
---|---|---|---|---
1| 65103| Hex Nut (#8-32)| 194|
2| 65923| Small Bolt (#8-32 x 3/8) (10 mm)| 194|
3| 65004| Small Screw (#8AB x 5/16) (8 mm)| 494|
4| 65900| Black Screw (#10B x 1/2) (13 mm)| 8|
5| 65109| Acorn Nut (#8-32) / Écrou borgne (#8-32)| 4|
The fasteners used in each step are shown actual size at the top of each page. If you are unsure which fastener to use, hold it up to the picture and use the one that matches.
ASSEMBLY BY KEY NO
FLOOR FRAME
NOTES:
Do NOT fasten your Floor Frames to your Base at this time. You will anchor
your building after it is erected.
The Floor Frame must be BOTH square AND level or the holes will not line up
properly.
Measure diagonally from corner to corner.
When diagonal measurements are equal, the Frame is square.
PRE-ASSEMBLY
Slides should be installed in Door Track prior to installation. However, if
this step is overlooked
or if the Slides need to be removed for maintenance, the following procedure
may be used.
To remove or install Door Slides:
- Remove Doors from Slides and set aside.
- Using pliers, bend down a corner of the Door Track.
- Remove or install Door Slides.
- Carefully bend the corner back into position.
CORNER PANELS
WALL ANGLE
WALL PANELS
DOOR JAMB
WALL CHANNEL
GABLES
CAUTION:
To avoid mishap on the sharp edge the edge trim must remain in place on the
top edge of the gable until right and left roof panels are in place.
ROOF BEAMS
ROOF PANELS
DOOR ASSEMBLY
If Doors do not align, raise or lower one side of the Door by placing the Door screws through a diff erent set of holes in the Door Slide.
ANCHORING OPTIONS
IMPORTANT
- If you have swing doors, they must hang and swing level before anchoring building.
- Anchor your building at this time. Use approprate 1/4” (6mm) X minimum 1 1/2” (38,1mmm) length hardware.
- Please take a moment to ensure that the building is installed in accordance with these instructions and with all applicable regulations.
- The entire fl oor frame MUST be securely anchored once the building is erected.
- Anchor your building at this time. Use appropriate 1/4”(6mm) X 1 1/2”(38,1mm) length hardware.