eurotech lighting YYR Series YYR15WCCT 18W CCT Button Instruction Manual
- June 4, 2024
- eurotech lighting
Table of Contents
YYR & YYS CCT Button
Model: YYR & YYS
Installation Instructions
YYR Series YYR15WCCT 18W CCT Button
All installations must be carried out by a qualified electrician following local regulations. Make sure that the power is switched off before installation. Please read and follow the ‘Installation instructions’ and ‘Safety instructions’ sections carefully before commencing installation. Installation of this model can change from time to time please read the instructions every time before installation. For detailed specifications, please go to our website eurotechlighting.co.NZ
Code:| Dimensions (mm):| Dimmable:| DoubleInsulated:|
IP Rating:| Kelvins:| Lumens:| Material:| Watts:
---|---|---|---|---|---|---|---|---
YYR15WCCT| 220Ø x 53D| Yes| Yes| IP54| 3K / 4K / 6K| 1250lm / 1300lm / 1350lm|
UV resistant Polycarbonate body and diffuser| 15W
YYR18WCCT| 280Ø x 53D| 3K / 4K / 6K| 1550lm / 1600lm /1650lm| 18W
YYR24WCCT| 330Ø x 53D| 3K / 4K / 6K| 2150lm / 2250lm / 2300lm| 24W
YYS15WCCT| 220L x 220H x 53D| 3K / 4K / 6K| 1250lm / 1300lm / 1350lm| 15W
YYS18WCCT| 280L x 280H x 53D| 3K / 4K / 6K| 1550lm / 1600lm /1650lm| 18W
YYS24WCCT| 330L x 330H x 53D| 3K / 4K / 6K| 2150lm / 2250lm / 2300lm| 24W
Product Information – YYR
Product Information – YYS
Saftey Instructions
Read these instructions carefully before commencing installation.
- The light source contained in this luminaire shall only be replaced by the manufacturer or this service agent or a similarly qualified person.
- This LED luminaire must be installed by a licensed electrician ONLY following all local regulations.
- Ensure that the cables will not be squeezed or damaged by sharp edges.
- Clean the light with a soft cloth and a standard PH-neutral detergent.
- Misuse of/or changes to the appliance shall void all warranties.
- Do not install on a surface that is not suitable or deformed.
- Do not install on or above a surface with a high temperature.
- There should not be any materials that are corrosive, or explosive.
Installation Instructions
-
Fix mounting bracket in relation to power entry.
a. For power entry from the ceiling make the central point of the bracket approximately 50mm up and 20mm across from the power cable.
b. For side power entry the bracket should be parallel to the angle of the cable.
Turn two pieces of white expansion tubes through the mounting holes.
Screw bracket in with 15mm screws for timber and 30mm screws for concrete surface. -
Prepare fitting for mounting.
a. Stick the black EVA anti-vibration pads onto the back surface of the lamp.
b. Set desired color temp with a switch on side of the fitting. -
Wire the fitting
a. Open the connector block cover by squeezing two clips and flipping up the cover
b. Peel back cables plastic insulation off 20mm. Connect the power to the Live and Neutral poles on the fast push terminal
c. Once the wire is secure press the waterproof cover down securely to create a tight seal. -
Fix the fitting to the ceiling.
After completing the wiring put the excess wire into the groove. Line up the bracket with the mounting point in the back of the fitting and push it to click into place.
Safety Instructions
Read these instructions carefully before commencing installation.
- The light source contained in this luminaire shall only be replaced by the manufacturer or this service agent or a similarly qualified person.
- This LED luminaire must be installed by a licensed electrician ONLY following all local regulations.
- Ensure that the cables will not be squeezed or damaged by sharp edges.
- Clean the light with a soft cloth and a standard PH-neutral detergent.
- Misuse of/or changes to the appliance shall void all warranties.
- Do not install on a surface that is not suitable or deformed.
- Do not install on or above a surface with a high temperature.
- There should not be any materials that are corrosive, or explosive.
For detailed specifications, please go to our websiteeurotechlighting.co.NZ