eurotech lighting SPEND15 Office Pendant Instruction Manual

June 4, 2024
eurotech lighting

eurotech lighting logo

SPEND15 – Pendant
Model: SPEND15
Installation Instructions

SPEND15 Office Pendant

All installations must be carried out by a qualified electrician following local regulations. Make sure that the power is switched off before installation. Please read and follow the ‘Installation instructions’ and ‘Safety instructions’ sections carefully before commencing installation.
Installation of this model can change from time to time please read the instructions every time before installation. For detailed specifications, please go to our website eurotechlighting.co.nz

Code:| Colour:| Dimensions (mm):| Ceiling Rose (mm):| Kelvins:| Lumens:| Material:| Suspension Cable:| Watts:
---|---|---|---|---|---|---|---|---
SPEND15| Black| 1532L x 103W x 23.5H| 92Ø x 30| 4000K| 3600lm| Aluminum| 2M| 36W

Installation Instructions

Mounting Options: A. = Suspended & B. = Linked – Straight Suspension
A. Suspended
A1. Drill hole for power cables. Gently knock-in mounting tubes. Fix the base of suspension cables to the ceiling.
A2. Pull the power cable through the ceiling slightly.
A3. Fix the ceiling rose bracket to the ceiling. Fix cable suspensions to the back of the fitting and then to the ceiling bracket. Adjust the height by pulling the wire through the locking point. Either coil extra wire or cut off allowing a height of 10mm. Feed fitting power cable along the suspension cable and into the ceiling rose.
Wire power cables paying attention to LIVE, neutral, and earth markings. Fix ceiling rose to the ceiling.eurotech lighting SPEND15 Office
Pendant

Safety Instructions

Read these instructions carefully before commencing installation.

  1. The light source contained in this luminaire shall only be replaced by the manufacturer or this service agent or a similarly qualified person.
  2. This LED luminaire must be installed by a licensed electrician ONLY following all local regulations.
  3. Ensure that the cables will not be squeezed or damaged by sharp edges.
  4. Clean the light with a soft cloth and a standard PH-neutral detergent.
  5. Misuse of/or changes to the appliance shall void all warranties.
  6. Do not install on a surface that is not suitable or deformed.
  7. Do not install on or above a surface with a high temperature.
  8. There should not be any materials that are corrosive, or explosive.

Installation Instructions
Mounting Options: A. = Suspended & B. = Linked – Straight Suspension
B. Linked – Suspended
B1. Drill hole for power cables. Gently knock-in mounting tubes. Fix the base of suspension cables to the ceiling.
B2. Pull the power cable through the ceiling slightly.
B3. Fix the ceiling rose bracket to the ceiling. Fix cable suspensions to the back of the fitting and then to the ceiling brackets. Adjust the height by pulling the wire through the locking point. Either coil extra wire or cut off allowing a height of 10mm. Feed fitting power cable along the suspension cable and into the ceiling rose. Wire power cables paying attention to LIVE, neutral, and earth markings. Fix ceiling rose to the ceiling. Fix the power cable to the suspension cable. Repeat suspension cable steps for linked models.
B4. Remove end caps of fittings you want to link at linking points. Then remove power cables from the fittings you are linking leaving the power cable in one fitting only. Slide in linkable parts so pendants are ready to be linked before you suspended them. Leave them unlinked as you will join them when suspended.
B5. Repeat step 3 for linkable items. Now that they are suspended you can link them together using the linkable parts provided.eurotech lighting SPEND15
Office Pendant - fig

Read these instructions carefully before commencing installation.

  1. The light source contained in this luminaire shall only be replaced by the manufacturer or this service agent or a similarly qualified person.
  2. This LED luminaire must be installed by a licensed electrician ONLY following all local regulations.
  3. Ensure that the cables will not be squeezed or damaged by sharp edges.
  4. Clean the light with a soft cloth and a standard PH-neutral detergent.
  5. Misuse of/or changes to the appliance shall void all warranties.
  6. Do not install on a surface that is not suitable or deformed.
  7. Do not install on or above a surface with a high temperature.
  8. There should not be any materials that are corrosive, or explosive.

For detailed specifications, please go to our website eurotechlighting.co.nz

eurotech lighting logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

eurotech lighting User Manuals

Related Manuals