Bonsenkitchen HB3203 Stainless Steel Hand Blender Instruction Manual

Bonsenkitchen HB3203 Stainless Steel Hand Blender

PRODUCT INFORMATION

Model : HB3203

Read this booklet thoroughly before using it and save it for future reference www.bonsenkitchen.com

IMPORTANT SAFEGUARDS
Like any electrical appliance, the Immersion Hand Blender must be handled with care at all times. To ensure your safety, the following precautions should be followed.

1. BEFORE USING YOUR IMMERSION HAND BLENDER, READ ALL INSTRUCTIONS CAREFULLY.

2. This product is not intended for people (including children) who are physically impaired, have sensory or mental disabilities, or lack relevant experience and knowledge unless someone responsible for their safety supervises or directs their use of the product.

3. Keep the product and its cables out of the reach of children.

4. The product is intended for home use. It is not intended for commercial use.

5. Please check if the voltage marked on the product matches the local power supply voltage, before connecting the product to the power supply.

6. Keep the power cord away from hot surfaces, sharp objects, or open fire.

7. Do not use this product if the plug, power cord, or product is damaged.

8. Do not submerge the power cord in water.

9. Do not let the cord hang over the edge of a table or counter, touch hot surfaces, or become knotted, trapped, or pinched.

10. Pulling or stumbling over the power cord can result in tilting over or falling off the appliance, causing serious injury.

11. If this appliance begins to malfunction during use, immediately unplug the cord.

12. Always insert the attachment first, then plug the cord into the outlet. To disconnect, switch the appliance off, then remove the plug from the wall outlet

13. Always unplug the appliance from the power supply if you leave it unattended. After use and before cleaning, always switch off the appliance and disconnect it from the power supply by taking the power cord connector out
    of the electric socket.

14. Do not immerse the MAIN BODY in water. To protect against electrical shock, do not immerse the cord, power plug, or appliance in any liquid, do not rinse under the tap.

15. Never use the appliance for any other purpose than what is described in this instruction book.

16. For indoor use only. Not intended for outdoor use.

17. The product must be allowed to cool before cleaning.

18. Be careful when handling and cleaning the blades. They are very sharp.

19. Always turn off the appliance and disconnect it from the power socket by pulling the power cord, before doing any of the following: replacing accessories or accessible parts that move during operation, cleaning or maintenance, and assembly and disassembly.

20. If the processed food starts to stick to the appliance (e.g. on BLADE, WHISK), switch off the appliance and clean the accessories carefully.

21. Never insert e.g. fingers, fork, knife, spatula, or spoon into rotating parts of the appliance or the accessories.

22. Before you remove the appliance or the drive unit from the container, let the rotating parts stop completely.

23. Make sure that your hair, clothes, and accessories do not get into close vicinity to the rotating parts.

24. Make sure that the power supply cable does not get between the rotating parts of the accessories.

25. Do not process food at a temperature exceeding about 176 F Foodstuffs should not be too hot, as splattering contents may cause scalding.

26. Do not wind the power cord around the appliance, this will reduce its life.

27. This appliance has a polarized plug (one blade is wider than another). To reduce the risk of electric shock, this plug will fit only one way into a polarized outlet. If the plug does not completely fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.

28. If the supply cord is damaged it must be replaced by the manufacturer o authorized service agent or a qualified technician to avoid a hazard

29. The appliance cannot be used for chopping ice or blending hard and dry ssubstances the blade could be blunted.

30. To reduce the risk of injury, never place the cutting blade on the base without first putting the bowl properly in place

31. The use of accessories not recommended by the manufacturer may cause Injuries to persons.

32. Always remove the blade assembly before pouring contents from the beaker.

33. Be sure the chopper lid is securely locked in place before operating the appliance.

PARTS & ACCESSORIES 

1. SPEED DIAL
2. POWER BUTTON
3. TURBO BUTTON
4. MAIN BODY
5. RELEASE BUTTON
6. BLENDER STICK COLLAR
7. BLENDER STICK
8. CHOPPER LID
9. BLADE
10. CHOPPER BOWL
11. EGG WHISK COLLAR
12. EGG WHISK
13. BEAKER

TECHNICAL DATA

• MODEL NO. : HB005-A (HB3203)
• POWER : 220-240VAC 50Hz 1 000W
• PRODUCT SIZE : 6. 77×2.17inches ( 172x55mm)
• NET WEIGHT: 2.73Ibs (1.24kg)

PACKAGE CONTENTS

ITEM AND QUANTITY

• MAIN BODY 1 PC
• BLENDER STICK 1 PC
• EGG WHISK COLLAR 1 PC
• EGG WHISK 1 PC
• BEAKER (AS) 1 PC
• MANUAL 1 PC
• CHOPPER (AS) 1 PC

USING YOUR IMMERSION HAND BLENDER

Before the first use, clean the blender according to the section “Quick cleaning”. The maximum operation time should be less than 1 minute each time, and a 30-minute rest time must be maintained after 5 consecutive cycles (one minute of work and one minute of stop is one cycle).

WARNING : Sharp blade on BLENDER STICK! Handle with extreme care.

IMMERSION HAND BLENDER CONTROLS

1. SPEED DIAL
   Adjust the blending speed from 1 to 20. (With the POWER BUTTON pressed)

2. POWER BUTTON
   Press and hold to use the Immersion Hand Blender. To stop blending, release the button.

3. TURBO BUTTON
   Press and hold to use maximum power. To stop blending, release the button.

OPERATING INSTRUCTION FOR BLENDER

1. Place food into the BEAKER.
   Note : When blending the carrots, cut the carrots into small pieces and put them in BEAKER, then add the water (the ratio of carrots to water is 2:3).

2. Align the MAIN BODY with the BLENDER STICK and push the pieces together until you hear and feel them click together. It may be helpful to press the RELEASE BUTTON when assembling.

3. Plug the Power Cord into a power outlet.

4. Lower the blender into food. Then press and hold the low-speed button or high-speed button to start operating.

5. To stop the blender release the low-speed button or high-speed button.

6. Unplug the Power Cord from the power outlet.

7. To remove, press the RELEASE BUTTON and unplug the BLENDER STICK.

OPERATING INSTRUCTION FOR EGG WHISK

• When stirring food in non-standard containers (such as pots or glass bowls, etc.), the knife head can not be exposed to the level of the liquid, otherwise the food liquid will splash.
  Note : Items such as pots or glass bowls for operating demonstrations.” For operational demonstration only, not standard with the product”

• Put the egg whites into the cup,  usually, two egg whites are enough.

• Insert the EGG WHISK into the EGG WHISK COLLAR. Ensure that the ribs on the EGG WHISK are aligned with the slots in the hole. Press firmly until you here a “click” and check EGG WHISK is locked into place.

• Align the MAIN BODY with the EGG WHISK and push the pieces together until you hear and feel them click together.

• Plug the Power Cord into a power outlet.

• Lower the EGG WHISK into food.

• Then press and hold the low-speed button or high-speed button to start operating.

• To stop the EGG WHISK by releasing the low-speed button or high-speed button of the motor unit.

• Unplug the Power Cord from the power outlet.

• To remove, press the RELEASE BUTTON and unplug the BLENDER STICK COLLAR.

OPERATING INSTRUCTION FOR CHOPPER

1. Place the BLADE on the center pin of the CHOPPER BOWL. Press down the BLADE and lock the CHOPPER BOWL.
   • NOTE: Always place the CHOPPER BOWL on the anti-slip base.
   • NOTE: To reduce the risk of injury, never place BLADE on CHOPPER BOWL without first putting CHOPPER BOWL properly in place.
2. Place the food in the CHOPPER BOWL.
   • NOTE : Debone the meat and cut it into small pieces, then place the meat in CHOPPER BOWL. The maximum amount of meat per blending cannot exceed 16 ounces.
3. Rotate the CHOPPER LID clockwise to fit into the CHOPPER BOWL.
4. Insert the MAIN BODY into the hole of the CHOPPER LID until it locks.
5. Plug the Power Cord into a power outlet.
   • NOTE: Do not lift the BLADE before the chopping operation has completely finished.
6. Press and hold the low-speed button or high-speed button to start operating.
   • WARNING: Do not operate the blender for longer than 60 seconds at a time. Failure to do so can result in overheating.
   • NOTE : Be sure the CHOPPER LID is securely locked in place before operating the blender.
7. To stop the chopper by releasing the low-speed button or high-speed button.
8. Plug the Power Cord into a power outlet.
9. Press the RELEASE BUTTON and unplug the MAIN BODY.
10. Open the CHOPPER LID by turning it anti-clockwise and remove the chopped food.

NOTE : Rotates counter-clockwise when opened.

PROCESSING GUIDE
(FOR S00ML CHOPPER BOWL)

PROCESSING GUIDE
(FOR 700ML BEAKER)

RECOMMENDED USE CHART
Refer to the table below for a guide on recommended use for different food types

CLEANING AND MAINTENANCE

NOTE : Do not immerse the MAIN BODY in water.

NOTE : Do not immerse the detachable stem of the blender in water because over time the lubrication on the bearings may wash away.

This appliance requires little maintenance. It contains no user-serviceable parts. Do not try to repair it yourself. Contact the Customer Service Department for any unusual issues you may experience.

1. Always unplug the Immersion Hand Blender before cleaning.
2. Ensure the Immersion Hand Blender has cooled down before cleaning.
3. Be very careful when cleaning BLENDER STICK blades, the blades are very sharp.
4. To clean the MAIN BODY, wipe down with a clean, damp cloth and dry thoroughly after every use. Never submerge in water or other liquids. DO NOT place BLENDER STICK COLLAR OR EGG WHISK COLLAR or CHOPPER LID in water.
5. Never use harsh chemical detergents, powder, or scouring pads on any of the parts.
6. To clean all detachable parts and accessories, wipe with a soft cloth and mild detergent before rinsing again. Soak in hot water for a few hours for easy cleaning. Then wipe down with a damp cloth and allow to dry.
7. Do not place the Immersion Hand Blender, or any of its attachments in the dishwasher, as this will damage internal components. Do not use abrasive cleaners.
8. Store the Immersion Hand Blender in a clean, dry place.
9. Contact Customer Service for any issues or malfunctions.

Quick cleaning
Between processing tasks, hold the hand blender in the beaker half filled with water and turn it on for a few seconds.

TROUBLE SHOOTINGS

Check whether the power cord plug position is pressed in place to check whether to send the opening.
The mixing rod and the MAIN BODY can not be assembled.| Check the mixingrod and the MAIN BODY need to be aligned with the silk screen solution position and the knob is in place as required.
The chopper and the MAIN BODY cannot be assembled.| Check whether there is debris in the CHOPPER LID, if not, check whether the position of the MAIN BODY is aligned with the slot on the CHOP­ PER LID and fits in place. It can work when it is in place.

WARRANTY CLAIM PROCEDURE
To ensure quick processing of your case, please observe the following instructions: Please have the till receipt and the item number (S/N: 1 2345) available as proof of purchase. You will find the item number as a sticker on the rear or bottom of the appliance. If malfunctions or other defects occur, please contact our customer service listed either by telephone or by email.

If you request any further assistance, please contact us: Customer service: customer-service@bonsenoa.com

ENVIRONMENT-FRIENDLY DISPOSAL

Disposal: Guideline 2012/19/EC concerning the handling, collection, recycling, and disposal of electrical and electronic equipment and their components ‘waste electrical and electronic equipment’, known as WEEE”  The crossed symbol on a rubbish container indicates that the machine or device is not allowed to be disposed of, but must be handed over to an appropriately equipped collection point for proper recycling or disposal.

Directive:
The packaging materials have been selected for their environmental friendliness and ease of disposal and are therefore recyclable. Dispose of packaging materials that are no longer needed in accordance with applica­ble local regulations.  This machine corresponds to the requirements according to EU Guideline 2014/30/EU entitled ‘Electro-Magnetic Compatibility’ 2014/35/EU entitled ‘Low-Voltage Guidelines’.  The product corresponds to the requirements according to UK Directive regulation technical documentation as well as the UK declaration of conformity the required UKCA marking .

TAN MET INT’L BUSINESS LTD 9 Pantygraigwen Road, Pontypridd, Mid Glamorgan, CF37 2RR, UK tanmetbiz@outlook.com

Manufacture : Bonsen Electronics Limited
ADDRESS :No.11-12, Lun Pin Chong Industrial Zone San Tun Community, Hou Jie Town 523941 Dongguan City, Guangdong PEOPLE’S REPUBLIC OF CHINA
Customer-service@bonsenoa.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>