NEXO ID24 Compact Loudspeaker User Manual

DP2117 – 08d – DI
ID24 – ID24-I

ID24 Compact Loudspeaker

User manual

EU Conformity declaration

We,| NEXO SA
ZA DU PRE DE LA DAME JEANNE
60128 PLAILLY – France
---|---
Declare under our sole responsibility that the product| Loudspeaker
Type| ID24
Serial number| On the product
Is in conformity with the provisions of the following directive including all applicable amendments:| 2014/35/UE (Low Voltage Directive)
Applied rules and standards:| EN 13155, EN 62368
Plailly, December, 2015| Joseph CARCOPINO, R&D Director

WARNINGS

PRECAUTIONS
Do not open the speaker, do not try to disassemble it neither to modify it in any way. The system doesn’t include any user-repairable part.
If the system seems to be malfunctioning or damaged, stop using it at once and have it repaired by a NEXO qualified technician.
Do not expose the system directly to the sun or to the rain, do not immerse it into fluids, do not place objects filled with liquid on the system. If a liquid gets into the system, please have it inspected by a NEXO qualified technician.
When flying outdoor systems ensure that the system is not exposed to excessive wind or snow loads and is protected from rainfall.
In case of wind greater than 8 on Beaufort scale (72km/h – 45mph), a touring system has to be landed or an additional securing has to be implanted.
For fixed installations, wind loading has to be taken into account in accordance to the national standards
The connection should be performed by qualified technician, by ensuring that power is off.
Operating temperature with temperate climate: 0°C to +40°C (+32°F to +104); -20°C à +60°C (-4°F to +140°F) for storage.

SAFETY INFORMATIONS

Read this manual before using the speaker.
Keep this manual available for further reference.
Observe all warnings and cautions.
Please check the NEXO Web site nexo-sa.com to get the most up-to-date version of this manual.
Ensure you are aware of the safety rules applying to rigging, stacking or installing on tripod or speaker stand. Failure to observe these rules may expose persons to potential wounds or even death.
Only use the system with accessories specified by NEXO.
Please always consult a NEXO-accredited technician if the installation needs architectural works and observe following precautions:

Mounting Precautions:

• Please select screws and mounting location supporting 4 times the system weight.
• Do not expose the system to excessive dust, vibrations, to extreme cold or hot temperatures, to reduce the risk of damaging components.
• Do not place the system in an unstable position: it could fall accidentally.
• If the system is used on a tripod, please ensure the tripod’s specifications are adapted and that its height does not exceed 1.40m/55”. Do not move the tripod with the system in position.

Connection and Powering Precautions:

• Unplug connected cables before moving the system.
• Power off the system before connecting the system.
• When switching on the installation, the amplifier must be powered last; when switching the installation off, shut off the amplifier first.
• If you work by cold temperatures, progressively raise the level to nominal value during the first minutes of use, to allow the system components to stabilize.

Please check regularly the system condition.

HIGH SOUND PRESSURE LEVELS
Exposure to very high sound pressure levels may cause permanent hearing losses. Degrees of hearing losses may be different from one person to another, but almost everybody will be affected if exposed to high sound pressure levels during a long period of time.  The OSHA (Occupational Safety and Health Administration) American Agency specified the following maximal exposures:

WASTE OF ELECTRIC OR ELECTRONIC EQUIPMENT
**** This symbol on the product or its packaging indicates that this product must not be treated as household waste. Instead, it is your responsibility to hand it over to a designated collection point for the recycling of waste electrical and electronic equipment.
By ensuring your waste equipment is recycled, you will help prevent potential negative consequences for the environment and human health, which could appear if this product was not recycled. Recycling helps spare natural resources. For more information about the recycling of this product, please contact your local city office, your household waste disposal service or your reseller.

EQUIPMENT

ID24

• Safety slot on the back to secure ID24.
• Kensington Security Slot on the back.
• 5 prints (top, bottom, rear and each sides) for IDT-QRA / IDT-TCBRK
• Rear panel plate for IDT-GSTK
• 1 M10 threaded insert for IDT-TVP (WARNING, for other fasteners, the length of thread must be less than 12mm).
• 2x M10 threaded insert on ID24 with the last 6 digits of the serial number ≥ 200 000 for IDT-TVP –IDT-HBRK24 (WARNING, for other fasteners, the length of thread must be less than 12mm).

ID24-I

• Safety slot on the back to secure ID24.
• Kensington Security Slot on the back.
• 6 x M6 threaded inserts on the speaker belt for mounting accessories.
• 2x M8 threaded insert on ID24 with the last 6 digits of the serial number ≥ 200 000 for IDI-HBRK24 (WARNING, for other fasteners, the length of thread must be less than 12mm).

Assembly on distance rod or speaker stand

Place distance rod on the connector plate (M20) of the Sub. Place ID24 on the distance rod / monitor stand|
---|---
IMPORTANT
Speaker stand must be rated for ID24 weight.
Speaker stand must always be installed on a horizontal surface.
Stand height and footprint must be defined to prevent assembly from collapsing.
Ensure that audience is not allowed within a safety area which radius is equal or higher than assembly height.
Test steadiness of the assembly by pushing in all directions.

DESCRIPTION

– The ID24 is a compact full-range 2-way speaker, equipped with two 4” speakers (in a V-shape arrangement) and a rotatable HF horn. The horn can be rotated easily, without tools, to choose the HF covering angle.
– ID24 HF Dispersion:

• 60° – 60°: ID.24-I6060 / ID.24-I6060PW / ID.24T6060 / ID.24-C
• 90° – 40°: ID.24-I9040 / ID.24-I9040PW / ID.24T9040 / ID.24-C
• 120° – 60°: ID.24-I12060 / ID.24-I12060PW / ID.24T12060 / ID.24-C
• 120° – 40°: ID.24-I12040 / ID.24-I12040PW / ID.24T12040 / ID.24-C

– The ID24 can be used alone or with a IDS110 or IDS210 subwoofer.

• 1x ID24 for 1x IDS110
• 2x ID24 for 1x IDS210

– Versions:

• ID24t : for « Touring » applications.
• ID24i : for fixed installations.
• ID24c : A la carte.

– Connections:

• ID24t: The speaker is equipped with two Speakon NL4 connectors, with parallel-wired pins – the ID24t uses the 2+/2- pins. The 1+/1- pins are used by the subs.
• ID24i: The speaker is supplied with a fixed cable 2×1.5mm2 section, length 1m, outside diameter 9mm ±1mm.
• (+): brown ; (-) : blue

– Amplification:

• The ID24 speakers MUST be used with a NEXO processor to handle EQ, phase alignment, crossover and excursion/thermal protection for the system loudspeakers. There are two NEXO processor series supporting the ID24 speakers: NXAMP (4-channel) amplified processors and DTD processors DTD (stereo + sub). DTD processors ensure optimal performances when used with DTDAMP power amplifiers.
• The following table shows the number of ID24 speakers and IDS110 / IDS210 subwoofers usable with each solution.

| NXAMP4x1 MK2| NXAMP4x2 MK2| NXAMP4x4| DTD + DTDAMP 4×0.7| DTD + DTDAMP 4×1.3
---|---|---|---|---|---
ID24| 1 to 4 per channel| 1 to 8 per channel| 1 to 8 per channel| 1 to 3 per channel| 1 to 4 per channel
IDS110| 1 or 2 per channel| 1 or 2 per channel| 1 or 2 per channel| 1 per channel| 1 per channel
IDS210| 1 per channel| 1 per channel| 1 per channel| |
| Recommended| | | |

PRESET

ID24 setups are available for each directivity with four different kind of setups targeted for specific applications. Please take some time to listen to these different setups and select the one that matches your needs best. Each setup can be used with three different crossover frequency (total is 4 directivities x 4 kind of setups x 3 crossovers = 48 different setups).

• MAIN is the recommended setup for most FOH application, similar to previous firmware setup.
• FRONT FILL is recommended when used as a front fill in a complement of a larger system.
• MONITOR is recommended for monitor applications. Warning: this setup is a low latency setup and therefore its phase is not compatible with other Nexo cabinets, including subs.
• LOUNGE is recommended for Club and Lounge applications.

ID24

Front of house and stage monitor applications

ID24+ Sub

Front of house applications with Sub

HORN ROTATION

• The ID24 speaker can be used in horizontal or vertical position.
• The horn can be rotated without tools: push the button on the ID24’s rear panel and turn it by 90°.
• Different mounting possibilities and horn rotation allow to deal with every request (e.g. with a 120°x40° horn, below).

CROSSOVER FREQUENCY

Please choose the crossover frequency value according to application:

• 95Hz Full range application.
• 120Hz Use with a NEXO subwoofer, e.g. IDS110 or IDS210.
• 150Hz Use as « front fill » on stage, complementing a main system.

ACCESSORIES

IDT-GSTK
Ground Stacking accessory

Place GSTK on ID24t.
Refer to the Product Data Sheet.

IDT-TCBRK2538-V2 / TCBRK3851-V2 / QRA-V2
Quick release Clamp
Truss Clamp

Place QRA/TCBRK on ID24t.
Secure the assembly.
Refer to the Product Data Sheet.

VNT-TVP (IDT-TVP)
Adaptateur M10 vers 35mm. Screw IDT-TVP on M10 Insert. Place them together on 35mm Tube.
Secure by Locking Screw.
Refer to the Product Data Sheet

IDT-HBRK24
Touring Bracket ID24t
(only used with ID24-T with the last 6 digits of the serial number ≥ 200 000)

Place HBRK24 on ID24t.
Adjust the angle, tight properly.
Refer to the Product Data Sheet

IDT-POLE32x1400
Distance Rod for ID24t et Sub
Ø32mm x 1400mm

Screw adapters M10 on the Sub and on ID24t by hand without tools.
Place distance rod, tighten the two clamping knobs
Refer to the Product Data Sheet

IDI-HBRK24
Fixed Bracket for ID24-I
(only used with ID24-T with the last 6 digits of the serial number ≥ 200 000) Place HBRK24 on ID24-I.
Adjust the angle, tight properly.
Refer to the Product Data Sheet

VNI-WB02 (IDI-WB02)
Wall mount 15kg max

Screw speaker plate to ID24-I (use screwsprovided with ID24-I).
Refer to the Product Data Sheet

VNI-WM01 (IDI-WM01)
Wall mount adapter 15kg max; 0° to 30°. Screw speaker plate to ID24-I (use screws provided with ID24-I).
Refer to the Product Data Sheet

VNI-WM02 (IDI-WM02)
Wall mount adapter 25kg max; 0° to 30°.

Screw speaker plate to ID24-I (use screwsprovided with ID24-I).
Refer to the Product Data Sheet.

ARRAY EQ

The ArrayEQ allows to adjust the system frequency response in its lower range (see curves below, with different ArrayEQ values):

MAINTENANCE

NOTE:
Speakers and Grills can be sent back to NEXO for recycling

1.1 Grille
ID24t

Remove the 4 screws and the 2 Fixgrill.
Tightening torque: 1 Nm|
---|---
Remove the grille from the 4 plastic bolts (2 on the top and 2 on the bottom).|
Pull forward.|

ID24i

Remove the 4 screws and the 2 Trifix.
Tightening torque: 1 Nm|
---|---
Remove the grille from the 4 plastic bolts (2 on the top and 2 on the bottom).|
Pull forward.|

1.2 Horn (remove the grille before)

Remove the screw and the knob (take care with the spring). Slide the horn forward (be careful with the cables).
Tightening torque: 1.7 Nm|
---|---
Remove the 2 screws to change the horn.
Tightening torque: 1 Nm|
Align the marks to reassemble.|

1.3 4” driver

Remove the 4 screws and the driver.
Tightening torque: 1.5 Nm|
---|---
Remove the gasket.|
Reassemble the driver with the plug facing towards the horn.|

1.4 HF Driver

Remove the 2 screws.|
---|---
Remote the 4 screws for changing the diaphragm.
Tightening torque: 0.5 Nm|
Align the marks to reassemble.
Tightening torque: 1 Nm|

1.5 Spare parts.
ID24t

ID24i

TECHNICAL SPECIFICATIONS

ID24 WITH NEXO ELECTRONICS

SPECIFICATIONS

’’ throat – Neodymium Magnet
Material| Water-resistant Polyurethane
Finition| White: Structural paint
Black: Raw sandblasted polyurethane| A la carte
Grid| Stainless steel Acoustical fabric, black or white| Stainless steel Black paint| A la carte
Rigging| 6x 6mm threaded inserts
2x M8 threaded insert (last 6 digits of the serial number ≥200 000 )| 6x prints for quick rigging
M10 threaded insert
2x M10 threaded insert (last 6 digits of the serial number ≥200 000 )| A la carte, among:
6x Inserts 6mm
2x M8 threaded insert
(from serial number 10000)
6x prints for quick rigging
M10 threaded insert
2x M10 threaded insert (last 6 digits of the serial number ≥200 000 )
Weight| 6 kg – 13 lb
Dimensions|

Application Notes are available on the NEXO Web site, nexo-sa.com

USER NOTES

NEXO S.A.
arc d’activité de la Dame Jeanne
F-60128 PLAILLY
Tel: +33 3 44 99 00 70
Fax: +33 3 44 99 00 30
E-mail: info@nexo.fr
nexo-sa.com

References

• NEXO
• NEXO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>