NEXO ID14 / ID14-I User Manual
- June 6, 2024
- NEXO
Table of Contents
NEXO ID14 / ID14-I User Manual
EU Conformity declaration
WARNINGS
PRECAUTIONS
Do not open the speaker, do not try to disassemble it neither to modify it in any way. The system doesn’t include any user repairable part.
If the system seems to be malfunctioning or damaged, stop using it at once and have it repaired by a NEXO qualified technician.
Do not expose the system directly to the sun or to the rain, do not immerse it into fluids, do not place objects filled with liquid on the system. If a liquid gets into the system, please have it inspected by a NEXO qualified technician.
The connection should be performed by qualified technician, by ensuring that power is off.
Operating temperature with temperate climate: 0°C to +40°C (+32°F to +104); -20°C à +60°C (-4°F to +140°F) for storage.
SAFETY INFORMATIONS
Read this manual before using the speaker.
Keep this manual available for further reference.
Observe all warnings and cautions.
Please check the NEXO Web site nexo-sa.com to get the most up-to-date version of this manual.
Ensure you are aware of the safety rules applying to rigging, stacking or installing on tripod or speaker stand. Failure to observe these rules may expose persons to potential wounds or even death.
Only use the system with accessories specified by NEXO.
Please always consult a NEXO-accredited technician if the installation needs architectural works and observe following precautions:
Mounting Precautions :
- Please select screws and mounting location supporting 4 times the system weight.
- Do not expose the system to excessive dust, vibrations, to extreme cold or hot temperatures, to reduce the risk of damaging components.
- Do not place the system in an unstable position: it could fall accidentally.
- If the system is used on a tripod, please ensure the tripod’s specifications are adapted and that its height does not exceed 1.40m/55″. Do not move the tripod with the system in position.
Connection and Powering Precautions:
- Unplug connected cables before moving the system.
- Power off the system before connecting the system.
- When switching on the installation, the amplifier must be powered last; when switching the installation off, shut off the amplifier first.
- If you work by cold temperatures, progressively raise the level to nominal value during the first minutes of use, to allow the system components to stabilize.
Please check regularly the system condition.
HIGH SOUND PRESSURE LEVELS
Exposure to very high sound pressure levels may cause permanent hearing losses. Degrees of hearing losses may be different from one person to another, but almost everybody will be affected if exposed to high sound pressure levels during a long period of time. The OSHA (Occupational Safety and Health Administration) American Agency specified the following maximal exposures:
WASTE OF ELECTRIC OR ELECTRONIC EQUIPMENT
This symbol on the product or its packaging indicates that this product must not be treated as household waste. Instead, it is your responsibility to hand it over to a designated collection point for the recycling of waste electrical and electronic equipment. By ensuring your waste equipment is recycled, you will help prevent potential negative consequences for the environment and human health, which could appear if this product was not recycled. Recycling helps spare natural resources. For more information about the recycling of this product, please contact your local city office, your household waste disposal service or your reseller.
EQUIPMENT
3 locations for hanging, 1 on the back (2x M6 / 73mm pitch) and on each side (1x M10).
Assembly on distance rod or
speaker stand
Place distance rod on the connector plate (M10) of the Sub. Place ID14 on the distance rod / monitor stand
IMPORTANT
Speaker stand must be rated for ID14 weight.
Speaker stand must always be installed on a horizontal surface.
Stand height and footprint must be defined to prevent assembly from collapsing.
Ensure that audience is not allowed within a safety area which radius is equal or higher than assembly height.
Test steadiness of the assembly by pushing in all directions.
DESCRIPTION
→ The ID14 is a compact full-range coaxial speaker
→ ID14 HF Dispersion (upon ordering):
- 100° – 100°: ID.14-I100100 / ID.14-I100100PW / ID.14-T100100 / ID.14-T100100PW
- 90° 140°: ID.14-I90140 / ID.14-I90140PW / ID.14-T90140 / ID.14-T90140PW
→ Versions:
- ID14t: for “Touring” applications, black, white.
- ID14i: for fixed installations, black, white
→ ID14 can be used alone or with IDS108 subwoofer. ID14t is equipped with two Speakon NL4 connectors with parallel-wired pins, one on each side and two on the back. ID14t use 2+/2-. The 1+/1- pins are used by the sub.
→ ID14i is supplied with a fixed cable (HO7ZZ-F), 2x 0.75mm2 section, length
2m, outside diameter 6.1mm ± 1mm. (+):
Brown / Red; (-): Blue / Black
→ Amplification
- The ID14 speakers must be used with a NEXO processor to handle EQ, phase alignment, crossover and excursion/thermal protection for the system loudspeaker.
- The following table shows the number of ID14 speakers and IDS108 subwoofers usable with each solution.
PRESET
Please consult nexo-sa.com for NEXO TD Controllers firmware information.
For the ID14, the following setups are available:
→ MAIN is the recommended setup for most FOH application, similar to previous firmware setup.
→ MONITOR is recommended for monitor applications. Warning: this setup is a
low latency setup and therefore its phase is not
compatible with other NEXO cabinets, including subs.
Preset
- ID14 MON PA 100100, with high pass at 120 or 150 Hz.
- ID14 MON PA 14090, with high pass at 120 or 150 Hz.
- ID14 MAIN PA 100100, with high pass at 120 or 150 Hz.
- ID14 MAIN PA 14090, with high pass at 120 or 150 Hz.
ID14
Front of house and stage monitor applications
ID14 + IDS108
Stage monitor applications with Sub
Front of house applications with Sub
CROSSOVER FREQUENCY
→ 120 Hz: Default crossover, to be used without sub or with a small sub, e.g. IDS108.
→ 150 Hz: Used for high level application, for « front fill » on stage, with a large main system.
ACCESSORIES
WARNINGS
All ID14 accessories are specifically rated in agreement with structural computations.
Never use other accessories including push-pins when assembling ID14 cabinets than the ones provided by NEXO: NEXO will decline responsibility over the entire ID14 accessory range if any component is purchased from different supplier.
PROHIBITED: ID14 below ID14 or ID14 below IDS108 without dedicated accessory
IDT-HBRK14
Bracket for Touring or fixed use.
IDT-GSTK14
Ground stacking accessory.
IDT-POLE20X1400
Distance Rod for
ID14 and IDS108
Ø20mm x 1400mm
IDT-TVP
Bolt adapter M10 to 35mm.
IDI-14TO108
Adapter for ID14 on IDS108.
IDI-WM01
Speaker wall mount; 0° to 30°.
IDI-WB02
Universal speaker wall mount
IDT-4CASE14
Flight case for 4x ID14 and accessories
ARRAY EQ
The ArrayEQ allows to adjust the system frequency response in its lower range (see curves below, with different ArrayEq values):
ArrayEQ HF: only available on NXAMPmk2
MAINTENANCE
NOTE : Speakers and Grills can be sent back to NEXO for recycling
Driver access
Spare parts
TECHNICAL SPECIFICATIONS
USER NOTES
NEXO S.A.
Parc d’activité de la Dame Jeanne
F-60128 PLAILLY
Tel: +33 3 44 99 00 70
Fax: +33 3 44 99 00 30
E-mail: [email protected]
nexo-sa.com