NEXO ePS10 10 Inch Loudspeaker User Manual

NEXO ePS10 10 Inch Loudspeaker

Product Information

Specifications

• Product Type: ePS10
• Serial Number: DP6153-01c-DI
• IP Rating: IP55
• Applied Rules and Standards: EN 12100, EN 13155, EN 62368

Description

The ePS10 is a compact full-range 2-way speaker with asymmetrical HF dispersion. It can be used alone or with the eLS18 or eLS600 subwoofer. The speaker is equipped with 2 pairs (In/Out) of screw terminal blocks, allowing permissible cables from 0.75 mm2 to 3.31 mm2 (12 to 15 AWG) copper section. The maximum outside diameter of the cable should not exceed 11mm.

WARNINGS

PRECAUTIONS

Do not open the speaker, do not try to disassemble it neither to modify it in any way. The system doesn’t include any user-repairable part. If the system seems to be malfunctioning or damaged, stop using it at once and have it repaired by a NEXO qualified technician. Do not expose the system directly to the sun or to the rain, do not immerse it into fluids, do not place objects filled with liquid on the system. If a liquid gets into the system, please have it inspected by a NEXO qualified technician. When flying outdoor systems ensure that the system is not exposed to excessive wind or snow loads and is protected from rainfall. In case of wind greater than 8 on Beaufort scale (72km/h – 45mph), a touring system has to be landed or an additional securing has to be implanted. For fixed installations, wind loading has to be taken into account in accordance to the national standards The connection should be performed by qualified technician, by ensuring that power is off. Operating temperature with temperate climate: 0°C to +40°C (+32°F to +104); -20°C à +60°C (-4°F to +140°F) for storage.

SAFETY INFORMATIONS

Read this manual before using the speaker. Keep this manual available for further reference. Observe all warnings and cautions. Please check the NEXO Web site nexo-sa.com to get the most up-to-date version of this manual. Ensure you are aware of the safety rules applying to rigging, stacking or installing on tripod or speaker stand. Failure to observe these rules may expose persons to potential wounds or even death. Only use the system with accessories specified by NEXO. Please always consult a NEXO-accredited technician if the installation needs architectural works and observe following precautions:

Mounting Precautions:

• Please select screws and mounting location supporting 4 times the system weight.
• Do not expose the system to excessive dust, vibrations, to extreme cold or hot temperatures, to reduce the risk of damaging components.
• Do not place the system in an unstable position: it could fall accidentally.
• If the system is used on a tripod, please ensure the tripod’s specifications are adapted and that its height does not exceed 1.40m/55”. Do not move the tripod with the system in position.

Connection and Powering Precautions:

• Unplug connected cables before moving the system.
• Power off the system before connecting the system.
• When switching on the installation, the amplifier must be powered last; when switching the installation off, shut off the amplifier first.
• If you work by cold temperatures, progressively raise the level to nominal value during the first minutes of use, to allow the system components to stabilize.

Please check regularly the system condition.

HIGH SOUND PRESSURE LEVELS

Exposure to very high sound pressure levels may cause permanent hearing losses. Degrees of hearing losses may be different from one person to another, but almost everybody will be affected if exposed to high sound pressure levels during a long period of time. The OSHA (Occupational Safety and Health Administration) American Agency specified the following maximal exposures:

Number of Hours

| Sound Pressure Level (dBA), Slow Response
---|---
8| 90
6| 92
4| 95
3| 97
2| 100
1 ½| 102
1| 105
½| 110
¼ or less| 115

WASTE OF ELECTRIC OR ELECTRONIC EQUIPMENT

This product or its packaging indicates that this product must not be treated as household waste. Instead, it is your responsibility to hand it over to a designated collection point for the recycling of waste electrical and electronic equipment. By ensuring your waste equipment is recycled, you will help prevent potential negative consequences for the environment and human health, which could appear if this product was not recycled. Recycling helps spare natural resources. For more information about the recycling of this product, please contact your local city office, your household waste disposal service or your reseller.

EQUIPMENT

On each side of the cabinet, two M6 with 80 mm pitch plus one M10 fittings will connect the ePS10 to accessories (VNI-HCPL535, VNU-BUMP, VNU-HBRK535, or eye-bolts). The back of the speaker is fitted with 3x M6 (70mm pitch) to connect wallmount in both vertical and horizontal positions (VNI-WM02). 2 pairs (In/Out) of 7.62 mm pitch screw terminal blocks. Cables from 0.75 mm2 to 3.31 mm2 (12 to 15 AWG) copper section.

DESCRIPTION

• The ePS10 is a compact full-range 2 ways speaker
• Asymmetrical HF dispersion “PS” type.
• ePS10 can be used alone or with eLS18 or eLS600 subwoofer
• The speaker is equipped with 2 pairs (In/Out) of screw terminal blocks, permissible cables from 0.75 mm2 to 3.31 mm2 (12 to 15 AWG) copper section. Cable with maximum outside diameter of 11mm.
• To wire ePS10, slit the membrane of the grommet crosswise, pass the cable through and make the connection to the screw terminals. Place the IPCOV.
• IP55: be careful to place the IPCOV correctly.
• Amplification
  • The ePS10 speakers must be used with a NEXO processor to handle EQ, phase alignment, crossover and excursion/thermal protection for the system loudspeaker.
  • The following table shows the number of ePS10 speakers and eLS600 or eLS18 subwoofers usable with each solution.

→| DTD + DTDAMP4X0.7| DTD + DTDAMP4X1.3| NXAMP4X1mk2| NXAMP4X2mk2| NXAMP4X4mk2
---|---|---|---|---|---
ePS10| 1 per bridged channels| Up to 2 per channel| 1 per channel | Up to 4 per channel| Up to 4 per channel
eLS600| X| 1 per channel| 1 per channel | Up to 2 per channel| Up to 2 per channel
eLS18| 1 per bridged channels| 1 per bridged channels| 2 per bridged channels| 1 per channel *| Up to 4 per channel

PRESET

Please consult nexo-sa.com for NEXO TD Controllers firmware information.

For the ePS10, the following setups are available:

• ePS10 MAIN PA, 60-120kHz
• ePS10 MAIN PA, 85-120kHz.
• ePS10 MAIN PA, 120-120kHz.

ePS10 ePS10 + eLS600

ePS10 + eLS18

HF DIRECTIVITY

The ePS10 speaker can be used in horizontal or vertical position. It’s easy to change the HF dispersion to deal with every request.

• Place a flathead screwdriver in the space between the grille and the cabinet to release the grille.
• Remove the 4 screws that hold the horn. Remove it.
• A sticker on the side of the horn indicates the side with the widest dispersion.
• Position the horn according to the desired HF dispersion.

CROSSOVER FREQUENCY

• 60 Hz: Full range application.
• 85, 120 Hz: Use with eLS600.

ACCESSORIES

WARNINGS

All ePS accessories are specifically rated in agreement with structural computations. Never use other accessories when assembling ePS10 cabinets than the ones provided by NEXO: NEXO will decline responsibility if any component is purchased from different supplier.
PROHIBITED: ePS10 below ePS10 or ePS10 below eLS600 or eLS18 without dedicated accessory

VNU-BUMP

LiftBar, can be used with VNI-WMADAPT.

Remove 2 screws on the top

Screw VNU-BUMP to ePS10 (use only screws provided with VNU-BUMP). Tight properly. Refer to the Product Data Sheet

VNT-TCBRK3551

• Rotary Truss Clamp

Place VNT-TCBRK3551 on VNU-BUMP at the desired hole.

VNU-HBRK535

• Horizontal Cradle, usable with: VNI-CLADAPT.
• VNI-WM330.
• VNU-PLADAPT

VNI-WMADAPT

• Wall mount adapter

Place VNI-WMADAPT on VNU-BUMP, use only fasteners provided. Tight properly.

VNI-CLADAPT

Ceiling Adapter, use with VNI-HBRK535. Screw VNI-CLADAPT to the ceiling (fasteners not provided). Place the assembly on VNI-CLADAPT, use the 2 guides. Tight with the fasteners provided with VNI-CLADAPT. Refer to the Product Data Sheet

VNU-PLADAPT

• Pole adapter

Place VNU-PLADAPT on VNI-HBRK535, use only fasteners provided. Tight properly. Refer to the Product Data Sheet

VNI-WM330

• Wallmount, usable with VNI-WMADAPT / VNU-BUMP VNU-HBRK535

ePS10 / BUMP / WMADAPT

Place the assembly on VNI-WM330. Tight with the fasteners provided with VNI- WM330. Refer to the Product Data Sheet

ePS10 / HBRK535

Place the assembly on VNI-WM330. Tight with the fasteners provided with
VNI-WM330.

VNI-HCPL535

Coupler ePS10 under horizontal eLS600

VNI-VCPL535

Coupler ePS10 under Vertical eLS18

VNI-WM02

Wall mount adapter 25kg max Remove 2 of the 3 screws on the back. Screw speaker plate to ePS10 (use only screws provided with ePS10). Place the speaker holder with ePS10 into wall bracket. Fix by tightening bolted assembly.

ARRAY EQ

The ArrayEQ allows to adjust the system frequency response in its lower range (see curves below, with different ArrayEq values):

MAINTENANCE

NOTE:
Speakers and Grills can be sent back to NEXO for recycling

Driver access

• Place a flathead screwdriver in the space between the grille and the cabinet to release the grille. Remove the grille.
• Remove the 4 screws to access the LF driver. Tightening torque: 3.5 Nm (Thread Locker: Loctite 242)
• Remove the 4 screws that hold the horn. Remove it. Tightening torque: 2.5 Nm (Thread Locker: Loctite 242)
• To access the HF diaphragm, remove the 4 screws. Tightening torque: 2.5 Nm

Reassemble the assembly and replace the grille.

• LF: red (+) / black (-)
• HF: orange (+) / grey (-)

Spare parts

TECHNICAL SPECIFICATIONS

WITH NEXO ELECTRONICS

SPECIFICATIONS

References

• NEXO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>