MOUNTUP MU0005-W Dual Monitor Desk Mount Instruction Manual

June 14, 2024
MOUNTUP

MOUNTUP logo MU0005-W Dual Monitor Desk Mount
Instruction Manual

MU0005-W Dual Monitor Desk Mount

MOUNTUP MU0005-W Dual Monitor Desk Mount

If you have any questions, please feel free to contact Customer Service via Amazon before returning.
WARNING!
If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help.
Before assembly, please check and make sure all necessary accessories are included and undamaged. Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

MOUNTUP MU0005-W Dual Monitor Desk Mount - PACKAGE
CONTENTSDO NOT EXCEED WEIGHT CAPACITY.

ASSEMBLY STEPS

Warm Tips
You could also refer to the Video Guide about installation on our product page.
STEP 1: Apply Pads to the Base Bottom
Apply pads (E1&E2) to the base bottom to avoid desk scratches.MOUNTUP
MU0005-W Dual Monitor Desk Mount - Base Bottom

STEP 2: Clamp Installation or Grommet Base Installation

OPTION A: Clamp Installation
Remove the plastic cover from Base (C).
Mount Clamp (D) to the bottom of Base (C) by tightening bolts (K) with 5mm Allen Key (I).MOUNTUP MU0005-W Dual Monitor Desk Mount - Grommet
BaseAdjust the Clamp width to fit your desk.
Secure stand to the desktop by tightening clamp (D). Fix the plastic cover to Base (C).MOUNTUP MU0005-W Dual Monitor Desk Mount - plastic
cover STEP 2: (Continued)
OPTION B: Grommet Base Installation
If existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount.
Firstly detach Bracket (D1) from Clamp (D).MOUNTUP MU0005-W Dual Monitor
Desk Mount - ClampThen remove the plastic cover from Base (C). Run Carriage Bolt(G) through Base (C).MOUNTUP MU0005-W Dual
Monitor Desk Mount - Plastic CoverBy tightening Wingnut (F) after making Bracket (D1) through Carriage Bolt (G) and stacked above Wingnut (F), Base (C) would be fixed to your desk securely. Install the plastic cover to Base (C) finally.MOUNTUP
MU0005-W Dual Monitor Desk Mount - plastic cover

**STEP 3: Arm Installation

**

Install the lower arm (B) to the base (C). Attach upper arm (A) to the lower arm (B). Secure the arm by tightening the inside screw using 3mm Allen key (H).
Note: If VESA plate is crooked, please hold it with both hands and rotate vigorously to make up arrows pointing up.MOUNTUP MU0005-W Dual Monitor Desk
Mount - Arm Installation

STEP 4: Attach Monitor

If VESA plate is crooked, please attach monitor and then hold the monitor with both hands and rotate vigorously to make up  arrows pointing up.MOUNTUP
MU0005-W Dual Monitor Desk Mount - Attach Monitor NOTE:
If the M-A screw is a little long, please use a H5mm spacer(M-C) to fix it.MOUNTUP MU0005-W Dual Monitor Desk Mount - little
long![MOUNTUP MU0005-W Dual Monitor Desk Mount

  • icon](https://manuals.plus/wp-content/uploads/2023/11/MOUNTUP-MU0005-W-Dual- Monitor-Desk-Mount-icon.png) OPTION A: Flat Back Monitor
    Firstly choose suitable screws (M-A) according to the hole size of your monitor back; then assemble two of them with 3-5mm space left.
    Next hang your monitor onto VESA plate of Upper Arm (A). Finally finish the attachment by using a 6mm Allen Key (J) to tighten all chosen screws (M-A).
    Please make sure you don’t tighten the screws much excessively or it may cause your monitor damage.MOUNTUP MU0005-W Dual Monitor Desk Mount - Curved Back
MonitorMOUNTUP MU0005-W Dual
Monitor Desk Mount - attach monitor OPTION B: Curved Back Monitor
    Firstly choose suitable screws (M-B) according to the hole size of your monitor back; then assemble two of them and Spacers (M-C) with 3-5mm space left.
    Next hang your monitor onto VESA plate of Upper Arm (A). Finally finish the attachment by using a 6mm Allen Key (J) to tighten all chosen screws (M-B) along Spacers (M-C).
      Please make sure you don’t tighten the screws much excessively or it may cause your monitor damage.

STEP 5: Tilt Adjustment

Problem:
Monitor tilts down.MOUNTUP MU0005-W Dual Monitor Desk Mount - Monitor tilts
down Solution:

  1. Loosen the tilting bolt.
  2.  Hold the bottom of monitor with one hand and adjust to determine your desired tilt angle.
  3. Retighten the tilting bolt to fix the intended angle.

MOUNTUP MU0005-W Dual Monitor Desk Mount - tilting
bolt STEP 6: Adjust Tension

The gas spring is pre-set to medium tension. For intended functioning of the mount, you will need to adjust the tension of Upper Arm (A) in accordance with your monitor weight by 6 mm Allen Key (J).MOUNTUP MU0005-W Dual Monitor
Desk Mount - Adjust Tension NOTE:
If the bolt is covered over, please hold the upper arm and press it down to maintain a horizontal position, and then you can see the adjustment screw at the joint. Be sure to keep the arm in a horizontal position during adjustment.
Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.
Solution:
Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended.MOUNTUP MU0005-W Dual Monitor
Desk Mount - Upper Arm Situation 2: Arm rises up or can’t press down Upper Arm with monitor rises up and fails to stay where intended.
Solution: Turn the inside screw clockwise(“-”direction) to decrease gas spring tension until the arm can stay as intended.

STEP 7: Cable Management

7-1 Remove Cable Cover

  • For lower arm: Remove the bottom plastic cover from lower arm as shown in the diagram below.

MOUNTUP MU0005-W Dual Monitor Desk Mount - Remove Cable
Cover 7-2 Attach Cable Cover

  • For upper arm: Run cables through the cable cover(A1), then with both hands slightly press inwards the tabs inside the cover and insert it to upper arm.
  • For lower arm: Run cables through the cable cover, then insert and slide the cover down for reattachment.

MOUNTUP MU0005-W Dual Monitor Desk Mount - Attach Cable
Cover

Adjust as Desired
Adjust monitor position and rotation.

  • Tilt
  • Swivel
  • Rotation
  • Height

MOUNTUP MU0005-W Dual Monitor Desk Mount - Adjust as
Desired Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.

Product Dimensions

MOUNTUP MU0005-W Dual Monitor Desk Mount - Product
Dimensions CAUTION AND MAINTENANCE:

  • Don’t allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors may lead to product damage or personal injury.
  •  Check if that the bracket is secure and safe to use at regular intervals (at least every three months).MOUNTUP logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals