USA-CLEAN X26R Ride On Auto Floor Scrubber Machine Instructions

X26R Ride On Auto Floor Scrubber Machine
Instructions

X26R Ride On Auto Floor Scrubber Machine

List
Standard Packing List

OPTIONAL PARTS

Replacement Cycle and Warranty Specification for Easily Wounded and Consumption Parts

EXECEPTION CLAUSE

1. Read and check the power supply size indicated on the nameplate before use, And conium that the current power supply meets the requirements of this product. In case of product damage or personal injury caused by
   Incorrect use of power supply, our compony is not foible.

2.  Do not use ii beyond Its rated load. If this causes damage to the ports, our company is not liable.

3.  Do not use in ultra-extreme environments (acidic, alkaline. too low or too high ambient temperature) , If any damage. occident or injury Is caused by ii, etc, our compony is not liable.

4.  Our company is not 6able for failure and damage caused by failure to use. maintain, keep or put foreign bodies in.

5. Our compony is not liable for damage or injury caused by unauthorized refitting of washing truces .etc.

ON CONSIGNMENT OF THE MACHINE
When the machine is consigned to the customer, an immediate cheek must be pardoned to ensure all the material mentioned in the shipping documents has been received, and also to cheek the machine has not suffered damage during transportation. If this is the case, the carrier must ascertain the extent of the damage at once, informing our customer service office. It is only by prompt action of this type that the missing material can be obtained, and compensation for damage successfully claimed.
To avoid harm to the operator and damage to the machine, please read the contents marked this symbol
carefully.
ATIENTION: Danger of exhalation of gas and leakage of corrosive liquids
ATTENTION: danger of fire: do not go near with free flames.

INTRODUCTORY COMMENT

This is a TVX floor scrubbing machine which, by means of the mechanical action of the rotating brush and the chemical action of a water/detergent solution, can clean any type of flooring. As it advances, it also collects any removed dirt as well as the detergent solution not absorbed by the floor.
The machine must only be used for this purpose. Even the best machines will only work well if used correctly and kept in good working order. We therefore suggest you read this instruction booklet carefully and read it again whenever difficulties arise while using the machine. If necessary, remember that our assistance service (organized in collaboration with our dealers) is always available for advice or direct intervention.
INTENDED USE
The scrubbing machine is designed exclusively for the professional cleaning of surfaces and floors in industrial, communal and public environments. The machine is only suitable for use in closed  or at least covered  locations.
The machine is not suitable for use in the rain, or under water jets. It is FORBIDDEN to use the machine for picking up dangerous dusts or inflammable liquids within places with a potentially explosive atmosphere. In addition, it is not suitable as n means of transport for people or objects.

TECHNICAL DESCRIPTION

SYMBOLS USED IN THE MANUAL Caution Danger of exhalation of gas

GENERAL SAFETY REGULATIONS

The regulations below must be carefully followed In order to avoid harm to the operator and damage to the machine.

♦ Read the labels on the machine carefully. Do not cover them for any reason and replace them immediately if they become damaged.
♦ The machine must be used exclusively by authorized, trained personnel.
♦ Outing the working of the machine, pay attention to other people and especially to children.
♦ Do not mix different types of detergent as this may produce harmful gases.
♦ Do not pack the machine when there is residual liquid In It.
♦ The storage temperature must be between -25° C and +55°c.
♦ Conditions of use: room temperature between 0°c and 40°C with relative humidity between 30 and 95%.
♦ Do not use the machine in an explosive atmosphere.
♦ Do not use the machine as a means of transport.
♦ Do not use acid solutions, which may damage the machine or harm the operator.
♦ Avoid working with the brushes when the machine is standing still, so as not to damage the floor.
♦ Do not vacuum inflammable liquids
♦ Do not use the device to collect dangerous powders.
♦ Do not use acid solutions, which may damage the machine or harm the operator.
♦ Avoid working with the brushes when the machine is standing still, so as not to damage the floor.
♦ Do not vacuum inflammable liqulds
♦ Do not use the device to collect dangerous powders.
♦ In the event of a fire, use a powder extinguisher. Do not use water.
♦ Do not knock against shelving or scaffolding, where there is a danger of falling objects.
♦ Select the operating speed according to the traction status.
♦ Do not use the machine on surfaces with an inclination greater than the one shown on the plate.
♦ When not in use, remove the keys and place the machine in a proper way to keep still.
♦ The machine is designed to carry out the washing and drying operations simultaneously. Different operations should only be carried out in areas where the passage of unauthorized persons is prohibited. Signal the presence of damp floors with suitable signs.
♦ If the machine does not work property, check this is not caused by failure to carry out routine maintenance. Otherwise, request the intervention of your dealer After-sale Service Centre.
♦ If you need to replace any components, request the ORIGINAL spare parts from a dealer or Authorized Retailer.
♦ Only use the brushes supplied with the device, or those specified in the Use and Maintenance Manual.
♦ Pull down the emergency brake immediately when there Is an operation risk.
♦ Before carrying out any maintenance work, switch off the machine and disconnect the battery connector.
♦ Make sure the whole electrical connection is recovered after maintenance.
♦ Do not remove any protection devices which require the use of special tools.
♦ Do not wash the machine with corrosive substances or with pressurized water.
♦ Send the machine to a Service Center nearby for servicing after 200 hours of use.
♦ To prevent the formation of scale in the solution tank filter, do not fill the tank with detergent solution many hours before using the machine.
♦ Before using the machine, check that all the hatches and covers are positioned as shown in this Manual.
♦ Before moving the recovery tank, empty the water.
♦ When disposing of consumption materials, observe the laws and regulations in force.
When your machine has reached the end of its long working life, dispose of the materials it contains in an appropriate manner (e.g. oil, batteries and electric parts), and bearing in mind that the machine itself was constructed using 100% recyclable materials

MACHINE PREPARATION

HANDLING THE PACKED MACHINE
The machine is fixed to a pallet, which is specially designed for forklift handling ..
Overall dimensions of the package
L: 1480mm
W:630mm
H: 1225mm
Total weight ( Including batteries ) : 310KG. It Is not possible to place more than two packages on top of each other.

1. Remove the outer packaging ( as figure )
2. The machine is fixed to the pallet with wedges and belts which block the wheel.
3.  Remove these belts.
4. Disengage the electronic brake, Pull the operating lever (Z) to the upper position (On the drive wheels)
5. Get the machine down from the pallet.

Keep the pallet for any More transport needs.
Handle the packed product with suitable rifting means that comply with the legal requirements.
During this operation, ensure that there are no people or objects near the machine.

OVER ALL INTRODUCTION

Ride on Scrubber Dryer

A:Brush head assembly
B : Squeegee assembly
C : Solution lank
D : Recovery tank
E: Recovery tank cover
F: Water level adjuster
G: Filler
H:Sleering wheel
I : Sewage pipe
J: Suction pipe
K:Outfall
L : Drive pedal
M : Brush head lifting lever
N : Squeegee lifting lever
O : Light
P: Chair
Q:Squeegee support
R : Rotate handwheel
S:Water filling nozzle
U:lnstrument panel
V: Level indicator for battery
X: Key switch meter
Y:Speed-control switch
Control panel
V: Level Indicator for battery meter
X : Key switch
Y : Speed-control switch
Z1 : Brush switch
Z2 : Squeegee switch
Z3 : Forward back switch ![USA-CLEAN X26R Ride On Auto Floor Scrubber Machine

• Control panel](https://manuals.plus/wp-content/uploads/2023/11/USA-CLEAN- X26R-Ride-On-Auto-Floor-Scrubber-Machine-Control-panel.png)TYPE OF BATTERY
  To power the machine there are three types of batteries below :
  Lead-acid battery composed of liquid plumbic acid, called WET Battery.
  Liquid electrolyte lead traction batteries, called AGM Battery.
  Sealed traction batteries with gas recombination or gel technology, called GEL Battery.
  For a good operating performance, we suggest the use of two 12V – 100 Ah batteries.
  OTHER TYPES MUST NOT BE USED.
  Max size of the battery : Length=330mm Width=170mm Height=240mm Max weight of the battery : 35kg. You are advised to always wear protective gloves, to avoid the risk of serious injury to your hands.
  You are advised to only lift and move the batteries with lifting and transportation means suitable for the specific weight and size.
  Connected the battery clamp at the top of the box and then put the battery into the battery compartment

BATTERY MAINTENANCE

The 1)1)8 of battery must satisfy the requirements of Standard CEl21-5 dissipation
The dimensions of the battery compartment are : 390mmx390mmx290mm.
To insert batteries proceed as follows:

1. Lock the machine by activating the electronic brake, and then tum the lever (on the rear right-hand side of the machine) anticlockwise.
2.  Make sure the recovery tank is empty, tum it as far as ii will go
3.  House the batteries in the compartment
4.  Tum the recovery tank back into position.

  You are advised to use airtight batteries only. to avoid the leakage of acids I
You are advised to always wear protective gloves, to avoid the risk of serious injury to your hands.
  This process must be carried out by qualified personnel. An incorrect connection of the connector may cause problems with machine functioning.
BATTERY MAINTENANCE
For maintenance and recharging, respect the instructions provided by the battery manufacturer.
Particular attention must be paid when choosing the battery charger. if not supplied, since there are different kinds according to the type and capacity of the battery.
BATTERY DISPOSAL
When the battery reaches the end of its working life, it must be disconnected by expert, trained personnel, then lifted lo remove it from the battery compartment.
  Exhausted batteries are classified as dangerous waste. When disposing. observe the laws and regulations in force.
RECHARGING THE BATTERIES
In order not lo cause permanent damage to the batteries it is essential to avoid their complete discharge:
arrange the recharge within a few minutes of the switching on of the flashing “discharged batteries” signal.
To connect the battery charger you must:
Move the machine near to the battery charger
Make sure the recovery tank is empty, otherwise empty it completely, and tum it as far as it will go:
To connect the battery charger you must:
To connect the battery charger you must:
Check the key switch Is on “O”; if this is not the case, tum the key of the main switch anticlockwise to 0º
Disconnect the electric system connector from the battery connector, and connect the battery charger to the battery connector. Keep the recovery tank open for the duration of the battery recharging cycle lo allow gas fumes to escape.
Danger of gas exhalation and leakage of corrosive liquids.
Danger of lire: do not go near with free flames.
BATTERY CHARGE LEVEL INDICATOR
The battery indicator has 8 positions and 1 blinking light.
10=100% blinking light = 0%

A few seconds after the indicators light comes on, the brush motor switches off automatically. With the remaining charge it is still possible, however, to complete the drying process before recharging.
HOW IT WORKS
Put the key switch (X) in position 1 (clockwise) and the power indicalor (V) will light up immedialely.
Machine walks forward when select the button (Z3) forward and push down the drive pedal (L). Tha adjustment of the speed will be carried out by varying !he pressure on the pedal (L).
Machine walks backward when select the button (Z3) back and push down the drive pedal (L). Adjust the speed by varying the pressure on the pedal (L)
Brush Drive
Brush works when select the button (Z3) forward and drop the brush head and push down the drive pedal (L). lt will no! work if !he brush head is raised or release the drive pedal (L)o
Suction Drive
Squeegee works when select the button (X) forward and drop the squeegee. It will stop working if raise the squeegee.   The reverse speed is lower than the forward speed to comply with current health and safety standards
When making even brief reverse movements, make sure !he squeegee is raised
DAILURE AND PROTECTION
When battery is low, all operation prohibited.
FILLING THE SOLUTION TANK
Before filling the solution tank

1. Remove the filler plug on the left or the machine and check that the solution filter is installed properly
2. Check that the solution filter cap (K), under the solution tank in the front left or the machine is properly closed .

The recovery tank must be completely empty each time the solution tank is filled
The solution tank can be filled as below:
Removing the inlet cap (S) and filling it using a rubber tube, left side or the machine. Fill with clean water at a temperature not exceeding 50°C.
The amount present in the tank can be seen through the level pipe on the front-right or the seat. The solution tank has a maximum capacity or about 85 liters. Add the liquid detergent to the tank in the concentration and manner indicated on the detergent manufacturer’s label.
To prevent the formation of excess roam that could damage the suction motor, use only the minimum amount of detergent that is necessary.
Always use detergents whose manufacturer’s label indicates their suitability for subbing machines. Do not use acid or alkaline produces or solvents without this indication. Acid or alkaline maintenance detergents can be used, as long as they have PH values between four and ten. and do not contain oxidizing agents, chlorine or bromine, formaldehyde, mineral solvents
Protective gloves should always be worn before handling detergents or acidic or alkaline solutions  to avoid serious injury to hands
Always use low foam detergent. To avoid the production of foam, before starting to clean, put a minimum quantity of antifoam liquid into the recovery tank. Do not use pure acids.
RECOVERYTANK
Make sure the recovery tank is empty, otherwise empty it completely. Check the cap of the drainage tube (I) (on the rear of the machine) is correctly closed.

ASSEMBLING THE SQUEEGEE

The squeegee, that for reasons of packaging comes dlsassembled from the machine, must be assembled while assembling the machine. Proceed as fonows for assembly:

1. Lift the squeegee (Q),tuming the left-hand lever (N) to move ii clockwise.
2.  Tum the main switch key anticlockwise to the “O” position.
3. Remove the key from the instrument panel.
4.  Loosen the knobs (R) in the squeegee pre-assembly.
5. Insert the left-hand squeegee pin in the left-hand slit of the squeegee connection.
6.  Insert the right-hand squeegee pin in the right-hand slit of the squeegee connection, then tighten the knob (R), making sure the washer and spring adhere in the upper part of the squeegee support.
7.  Insert the suction hose(J) in the squeegee sleeve.

These operations must be carried out using protective gloves to avoid any possible contact with the edges or tips of metal objects ADJUSTING THE SQUEEGEE HEIGHT
The height of the squeegee must be adjusted on the basis of the state of wear and tear of the rubber. Carry out the following operations for adjustment:

1. unscrew the locking nut;
2.  Rotating wheels, adjusting its height;
3.  Block it by tightening the locking nut once the required height is reached.

ASSEMBLING THE BRUSH

To assemble the brushes of the brush head body, proceed as follows:

1. Make sure that the main switch is in the “OFF-0” postilion.
2. Lift the brush head by turning the right lever (M) to move the brush head anliclockw1se.
3.  With the brush lead in a high position put the brushes in the housing of the plate under the brush head. turning them until the three buttons go Into the niches or the plate itself; turn the brush clockwise until the pin 1s pushed towards the coupling spring and is locked Into place.

You are always advised to wear protective gloves, to avoid the risk of serious injury to your hands. Cut down all electric current in order to protect your hands
During this operation. ensure that there are no people or objects near the brush.
ATTENTION: Check the brush Is correctly inserted. If this is not the case. the machine could move in an irregular, sudden manner.
EMPTY SOLUTION TANK DEVICE

1. To check the quantity of water in the solution tank there is a suitable level indicator tube (F) placed on the right of the driver seat.
2.  Push machine to the effluent discharge point. unscrew the water drain-pipe (K). the water discharged into the sewer. until the solion tank is empty.
3. Tightened the Solution tank drain pipe (K) cap. and then put it back to its position.

WORK

PREPARATION

Make sure the recovery tank is empty, otherwise empty it completely

1. Check the key switch (X) is on -o·; if this is not the case. tum the key of the main switch to -o·.
2.  Connect the battery connector to the electric system connector.
3.  Check the electronic brake
4. Sit on the driver’s seat
5. Tum the key of the main switch a quarter of a rotation cockwise The display on the instrument panel (V) will immediately come on. Please don’t have any operation within 5 seconds after boot, the machine should be self-checking;
6. Lower the brush head by turning the right lever clockwise, then lower the squeegee turning the left lever anticlockwise ; As soon as the forward movement pedal is activated with the brush head in its work position, the solenoid valve will start working and will begin dispensing detergent solution. As soon as the squeegee is in its work position, the vacuum motor will switch on and being working
7. elect the forward gear, and to do this use the switch on the steering column ;
8. Press the accelerator pedal (L) to start moving the machine :
9.  To go backwards, stop the machine and select the desired direction, and to do this use the switch (X) on the steering column and afterwards press down on the pedal (L) :

** During the first meters, check there is sufficient solution and that the squeegee dries perfectly. The machine will now begin to work with full efficiency until the battery is flat or the detergent solution has finished.
OVERFLOW DEVICE
Recovery tank is full, shuts off the air to the suction motor intake to protect it Then proceed with emptying the recovery tank through a special drainage pipe.
AT THE END OF WORK
** Al the end of the work, and before carrying out any type of maintenance, perfonn the following operations

1. Lifting the brush head by turning the right lever anticlockwise. then lifting the squeegee turning the left lever clockwise:

2. Move the machine to the designated drainage area.
   Before performing any maintenance, remove the keys from the panel and disconnect the battery connector of the machine

3. Tum the machine off by turning the key one quarter tum anticlockwise and remove it from the panel.

4. 0isconnect the tube (I) from its seat. unscrew the drainage cap (H) and empty the recovery tank.

5. Screw the drainage cap and replace the tube (I) back to the seat.

Be sure lo remove the key as well as tighten auxiliary brake on the drive Wheel when the operator leaves the seat, and parked machine for a long time

DAILY MAINTENANCE

CLEANING THE RECOVERY TANK

1. Bring the machine to the place provided for draining the water;

2. Disconnect the tube (I) from its seat. unscrew the drainage cap (H) and empty the recovery tank ;
   Before performing any maintenance, remove the keys from the panel and disconnect the battery connector of the machine. This operation must be carried out using gloves to protect against contact with dangerous solutions

3. Lift the recovery tank (El ;

4. Clean and rinse the recovery tank

5. Reassemble all the elements.

  Be careful not to hit the recovery tank float directly, as this would enable water to enter the vacuum motor connected to it
CLEANING THE SOLUTION TANK FILTER
Careful cleaning of the detergent/water solution filter ensures a better working capacity. Proceed as follows for cleaning

1. Check the main switch is on -o ;
2.  Loosen the filter (G) cap on the front of the machine
3.  Remove the internal filter cartridge and rinse everything thoroughly with running water
4. Reassemble all the elements

  Before purloining any maintenance, remove the keys from the panel and disconnect the battery connector
These operations must be carried out using gloves to protect against contact with dangerous solutions. CLEANING THE SQUEEGEE

The careful cleaning of the whole vacuum unit ensures better drying and cleaning of the floor as well as greater duration of the sucUon motor.

1. Remove the tube (J) from the squeegee.

2.  Release the Squeegee (Q) fixed nut (R), then take down the squeegee (B).

3.  Carefully clean the inside of the squeegee and rubbers.

4.  Every week, or whenever suction seems to be unsatisfactory, check the squeegee tube is not obstructed.
   To clean it.

5.  Reassemble all the elements again.

This operation must be carried out using gloves to protect against contact with dangerous solutions ![USA-CLEAN X26R Ride On Auto Floor Scrubber Machine

• CLEANING](https://manuals.plus/wp-content/uploads/2023/11/USA-CLEAN-X26R- Ride-On-Auto-Floor-Scrubber-Machine-CLEANING.png)

CLEANING

THE BATTERY COMPARTMENT
Empty the battery compartment each time you remove the batteries, check there is no fluids.
  This operation must be carried out using gloves to protect against contact with dangerous solutions.
Danger of lire: do not go near with free names.
Danger of exhalation of gas and leakage of corrosive liquids.

WEEKIY MAINTENANCE

CLEANING the BRUSH
Thorough cleaning of the brush will guarantee a better working capacity. Proceed as follows for cleaning:

1. Check the main switch is on ·o· (tum it to this position if necessary).

2.  Raise the brush head by turning the right-hand lever (M) anticlockwise.

3.  Tum down the brush.
   During this operation. ensure that there are no people or objects near the brush.

4. Take the brush and clean it under a flowing jet of water.

5. Reassemble it on the brush head body.

Replacing the squeegee rubbers

1. Remove the tube (J) from the sleeve on the squeegee.
2.  Rotate the nut(R) the squeegee.
3. Unthread the squeegee(B)
4.  loosen the screw that block the rubber-pressing blade and take down the plate stainless steel.
5. Reassemble the rubber, Then reassemble all the elements

TROUBLE SHOOTING

Before you take ii to repair or call our customer service to help, you should check out those problems.

2. Check out whether motor switch is on :
3. Check out whether the vol1age is good.| 1. Plug In the power and make sure the fuses are normal work :
2. Tum on the switch of motor :
3. The batteries are fully charged
Water can’t come out from the brush or slightly| 1. Filter or joint is dogged ;
2. Clean the drier ground at first ,so the water can’t catch up with it
3. The solenoid valve is dogged or rejected.| 1. Take down the filter and joint ,then wash them:
2. If the ground is drier, you must spray It extra :
3. Take down the solenoid valve, then wash It.
Suction abate| 1. The cover of recovery tank Is not sealed ;
2. Hose clamp loose
3. Suction Motor loose or defection:
4. The suction hose is no! completely blocked :
5. Battery low.| 1. Check the seal rubber of cover and make sure the cover will be sealed
2. Check out and lock the hose clamp;
3. Make sure the motor install well and tighten the screw
4. Dredge the pipe
5. Charge the batteries.
Fuse crack of battery terminal and cable healing| 1. Cable can’t lightened well that lead to bad contact:| 1. Tighten the screw
Water absorption is not clean| 1. Suction motor do not work ;
2. Suction hose is blocked :
3. The squeegee is blocked with something ;
4. The squeegee is totally worn-out
5. The height of the squeegee is not suitable.| 1. Check out the motor ( according to above) ;
2. Clean them ;
3. Clean them;
4. Change squeegee blade rubbers
5. Adjust the height of the squeegee.
The brush do not dean well| 1. The motor of the brush can not work
2. Dirt is too stubborn ;
3. Brush is serious abrasion :
4. Something twine round the brush.| 1. Check out the motor :
2. Use appropriate dealing fluid
3. Change the brush
4. Clean them.

CHOOSING AND USING THE BRUSHES

POLYPROPYLENE BRUSH ( PPL)
Used on all types of floors. Good resistance to wear and tear, and hot water (no greater than 60 °C). The
Polypropylene brush is non-hygroscopic and therefore retains its characteristics even when working in wet conditions.
NYLON BRUSH
Used on all types of floors. Good resistance to wear and tear, and hot water (no greater than 60°C). The
Nylon brush is hygroscopic and easy-extended; as a result it cannot retain its characteristics when working in wet conditions.
ABRASIVE BRUSH
The bristles of this type of brush are extremely hard. II is used to clean very dirty floors. To avoid floor damage, work only with the pressure strictly necessary.
STEEL BRUSH
It is made up of steel wire and artificial fiber blends and used to clean rough roads, floors with big joints or dirt which is difficult to clean up.
THICKNESS OF THE BRISTLES
Thicker bristles are more rigid and are therefore used on smooth floors or floors with small Joints. On uneven floors or those with deep joints, it is advisable to use softer bristles which can enter the gaps more easily.
**** Remember that when the bristles are whom and therefore too short, they will become rigid and are no longer able to penetrate and clean deep down. In this case, like with over-large bristles, the brush tends to jump.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>