SPIKE 44-7500 Fenders Set Yamaha Wolverine Installation Guide

June 6, 2024
SPIKE

SPIKE 44-7500 Fenders Set Yamaha Wolverine

**PART

44-7500**

INSTALLATION INSTRUCTIONS

IMPORTANT NOTICES


READ AND UNDERSTAND THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLATION TO AVOID INJURY TO YOURSELF, DAMAGE TO THE VEHICLE OR ACCESSORY

  • For proper installation, TWO people are required.
  • Torque specifications must be followed when tightening bolts. Over-tightening any and/or all screws will cause cracks around mounting holes which is not covered by any warranty.
  • As specified on carton label, damage caused by packaging staples is not covered by warranty. All staples must be removed prior to removing product from carton.
  • Failure to follow these installation instructions completely may void any warrantable components and result in product damage or personal injury.
  • Do not use Loctite or any other similar fastener adhesive. These types of products react to plastics and cause cracking. Not covered by any warranty.

DEALER

These instructions contain important information for future reference and must be given to the customer at time of purchase or upon completion of installation.

Parts List

(parts available with kit only and not available separately)

ITEM

| PART NAME|

DESCRIPTION

---|---|---

A

| Front left fender flare| CNC cut-out made of ⅛” thick high-density polyethylene
B| Front right fender flare|

CNC cut-out made of ⅛” thick high-density polyethylene

C

| Rear left upper fender flare| CNC cut-out made of ⅛” thick high-density polyethylene
D| Rear right upper fender flare|

CNC cut-out made of ⅛” thick high-density polyethylene

E

| Rear left lower fender flare| CNC cut-out made of ⅛” thick high-density polyethylene
F| Rear right lower fender flare|

CNC cut-out made of ⅛” thick high-density polyethylene

INSTRUCTION BAG

| G| Mounting hardware| Includes: 44 push type retainers 5/16″
H| Co-extruded SIDE bulb seal (⅛”)|

Includes: 18″ Co-extruded SIDE bulb seal (⅛”) / #77-108BS-SIDE [end user to cut to exact length]

PARTS IDENTIFICATION

IMPORTANT NOTICES


Torque specifications must be followed when tightening bolts.
Over-tightening any and/or all screws will cause cracks around mounting holes which is not covered by any warranty.

Installation

Front fender flares installation

(right side shown, passenger side)

a) Temporarily remove the OEM socket head screws (2x) located on the side of the front OEM fender as shown by the arrow.

b) Attach the front right fender flare part (Item B) to the OEM fender using the OEM socket head screw (2x) removed in previous step and temporarily secure the remaining section of the front right fender flare to the vehicle using spring clamps or any other clamping tools as shown below. Adjust the position of the fender flare and tighten all screws with specified torque indicated below.

c) Ensure that the front right fender flare is in proper position and use the remaining mounting holes (8x) as guide to drill 5/16 inch diameter holes through the vehicle front fender and secure right away with the supplied push type retainers as shown below.
WARNING: For each hole, a single (1) layer of OEM front fender should be drilled / pierced.


d) Repeat steps a) to c) for the front left fender flare part.

Rear upper fender flares installation

(right side shown, passenger side)

e) Temporarily remove the OEM socket head screw (3x) located under the rear OEM fender as shown by the arrow.

f) With the recessed groove of the rear right upper fender flare part (Item D) facing UP, bend DOWN 90 degrees the section exceeding the groove as shown beside.

g) Attach the rear right upper fender flare part to the OEM fender using the OEM socket head screw (3x) removed in previous step. Adjust the position of the of the fender flare and tighten all screws with specified torque indicated below.

h) Use the remaining mounting holes (7x) as guide to drill 5/16 inch diameter holes through the vehicle rear fender and secure right away with the supplied push type retainers as shown below.
**WARNING: For each hole, a single (1) layer of OEM rear upper fender should be drilled / pierced.

i)** Repeat steps e) to h) for the rear upper left fender flare part.

Rear lower fender flares installation

(right side shown, passenger side)

j) Temporarily remove the OEM socket head screw (2x) located under the rear OEM fender as shown by the arrow.

k) Apply the co-extruded SIDE bulb seal (Item H) to the rear right lower fender flare (Item F) edge as shown below using manual pressure to ensure good adhesion and cut any excess.

l) Attach the rear right lower fender flare part to the OEM fender using the OEM socket head screw (2x) removed in previous step. Adjust the position of the of the fender flare and tighten all screws with specified torque indicated below.

m) Use the remaining mounting holes (7x) as guide to drill 5/16 inch diameter holes through the vehicle rear fender and secure right away with the supplied push type retainers as shown below.
WARNING: For each hole, a single (1) layer of OEM rear lower fender should be drilled / pierced.

n) Repeat steps j) to m) for the rear left lower fender flare part.

Maintenance and Care

Tighten all hardware after first use and periodically thereafter.

www.spikepowersports.com

Documents / Resources

| SPIKE 44-7500 Fenders Set Yamaha Wolverine [pdf] Installation Guide
44-7500, Fenders Set Yamaha Wolverine
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals