ION Uber Boom Ultra Portable Bluetooth Boom Box with Speakerphone User Guide
- June 14, 2024
- ION
Table of Contents
- ION Uber Boom Ultra Portable Bluetooth Boom Box with Speakerphone
- Introduction
- Box Contents
- Setup
- Features
- Operation
- Bluetooth Connecting with UberTM Boom Ultra
- Stereo-LinkTM: Syncing Two Speakers
- Bluetooth Call Answering
- Connecting an Audio Device Using the Aux Input
- Karaoke Mode
- Light Modes
- Troubleshooting
- Technical Specifications
- Trademarks & Licenses
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
ION Uber Boom Ultra Portable Bluetooth Boom Box with Speakerphone
SUPPORT ionaudio.com/support
Introduction
Thank you for purchasing the UberTM Boom Ultra Speaker. At ION, your entertainment is as important to us as it is to you. That’s why we design our products with one thing in mind—to make your life more fun and more convenient.
Note: Before you first use the product, please fully charge the batteries.
Your unit was purposely shipped with a reduced battery charge to ensure safe
transit. For optimal charging, power off the speaker while charging.
Use the included USB-C cable to connect the unit to a power adapter connected
to a power outlet and let it charge for up to 4 hours. This helps ensure the
longest life for your battery.
Box Contents
- UberTM Boom Ultra
- USB-C Charging Cable (1.6 ft / 49cm)
- Quickstart Guide
Support
For the latest information about this product (documentation, technical
specifications, system requirements, compatibility information, etc.) and
product registration, visit ionaudio.com
For additional product support, visit
ionaudio.com/support
Setup
Charging & Battery Information
- When powered on, a full rainbow of lights will appear around the woofer of UberTM Boom Ultra for 1 second. Following this, the woofer lights will be lit or unlit for 2 seconds to correspond with the current battery percentage. See the images, right, for example.
- For the quickest charging time, power off UberTM Boom Ultra and use the included USB-C cable to connect the speaker to a USB power adapter (DC 5V 2A, not included) connected to a power outlet, or your computer (powered on).
- The charging LED (located next to the USB-C under the protective rubber panel on the rear panel) will appear solid red when charging, even if the speaker is powered off. The LED will turn off when charging is complete. When the UberTM Boom Ultra battery is less than 10%, the LED will continuously flash; If voice prompts are turned on, you will also hear “Battery Low”.
- If no audio is played through the UberTM Boom Ultra for 15 minutes, the unit will power off automatically to conserve battery life.
Features
Top Panel
-
Power Button: Press and hold this button to turn UberTM Boom Ultra on and off. When powered on, press quickly to cycle through audio source modes: Bluetooth, Aux, and USB/SD.
Double-press this button to disable or enable voice prompts. -
Bluetooth® Button: Press and hold this button to disconnect a Bluetooth device. See Operation > Bluetooth Connecting with UberTM Boom Ultra to learn how to connect a Bluetooth device.
-
Bass Boost Button: Press this button to enhance the speaker’s bass frequency response.
-
Lights Button: Press this button to cycle through light modes.
-
Play/Pause Button: Press this button to play and pause Bluetooth audio.
Press and hold this button to enter Stereo-LinkTM mode. See Operation > Stereo-LinkTM: Syncing Two speakers to learn more. -
Volume Up/Down Buttons: Press these buttons to adjust the speaker’s volume. Press and hold + or – to navigate Bluetooth tracks.
Rear Panel
Note: Use your fingernail to release the protective rubber panel on the
back of UberTM Boom Ultra to access the Rear Panel:
- Aux Input: Connect an MP3 or other audio player to UberTM Boom Ultra here using a 1/8 inch (3.5 mm) auxiliary cable (not included). See Operation > Connecting an Audio Device using the Aux Input for more information.
- Mic Input: Connect a microphone (not included) to UberTM Boom Ultra here using a 1/4″ cable.
- USB Port: Connect a USB flash drive here to play stored audio files.
- Micro-SD Card Slot: Insert a Micro-SD card here to play stored audio files.
- USB-C Charging Port: Connect the included USB-C cable to UberTM Boom Ultra here, then connect the other end to to a USB power adapter and plug it into a power outlet, or your computer (powered on).
- Reset Button: Press and hold this button for three seconds to reset UberTM Boom Ultra to the manufacturer’s default settings and clear the device’s Bluetooth connections memory.
Operation
IMPORTANT: To ensure the best possible experience with the app, use the
most current Android OS or iOS on your device.
Follow these steps to download the free app on your device:
- Open the Apple App Store or Google Play on your device. Then, search for the ION Sound XPTM app.
- Follow the on-screen instructions to download and install the app. Once downloaded, the ION Sound XPTM app will appear on your device’s home screen.
- Connect your device to UberTM Boom Ultra via Bluetooth. See the Bluetooth Connecting with UberTM Boom Ultra to learn how to do this.
- Open the ION Sound XPTM app. If prompted, allow the app to access your device’s Bluetooth and Location Services.
- Tap to select Add A Product on the screen. The app will scan and find UberTM Boom Ultra. If you are having issues connecting, tap Help with setting up? for additional tips.
- Select the UberTM Boom Ultra icon to go to the next screen, where you can use the app to control various functions of the speaker such as:
• Volume: Adjust the speaker’s volume.
• EQ: Adjust the speaker’s equalization.
• Voice Prompts: Enable or disable the voice prompts.
• Lights: Change the light modes.
• Mic Echo: Adjust the amount of echo applied to the microphone.
• Battery Life: Check the speaker’s battery life status.
• Support: Visit ionaudio.com, contact Technical Support, and view Warranty information and Frequently Asked Questions.
Bluetooth Connecting with UberTM Boom Ultra
-
Turn on UberTM Boom Ultra by holding down the Power button for 2 seconds. UberTM Boom Ultra will automatically enter Bluetooth pairing mode.
-
Navigate to your device’s Bluetooth setup screen, find Uber Boom Ultra, and connect. When connected, the woofer LEDs will be lit solid blue for 2 seconds and you will hear “Connected” (if voice prompts are enabled).
Note: Do not connect to iSP159_BLE; this is reserved exclusively for connecting to the ION Sound XPTM app. If you experience trouble in connecting, select “Forget this Device” on your Bluetooth device and try to connect again. -
Now you can use the buttons on the top panel to control audio playback:
• Press the Play/Pause button to play or pause the current track.
• Press and quickly release the Volume Up button to increase the volume by one increment.
• Press and quickly release the Volume Down button to decrease the volume by one increment.
• Press and hold the Volume Up button to skip to the next track.
• Press and hold the Volume Down button to revert to the beginning of the current track. Repeat this action within 1 second to skip to the previous track. -
To disconnect, turn off Bluetooth from your device’s Bluetooth settings, or press and hold the Bluetooth button. If voice prompts are enabled, you will hear “Bluetooth disconnected.” The blue woofer LEDs will spin to indicate the speaker is available to pair to a new device.
Stereo-LinkTM: Syncing Two Speakers
-
Be sure to disconnect Bluetooth devices before attempting to pair speakers using Stereo-LinkTM. Press and hold the Bluetooth button to do this.
-
Press and hold the Play/Pause button on each UberTM Boom Ultra speaker. The Bluetooth LEDs will begin to rapidly flash blue to indicate they are attempting to link. Please allow 10 to 30 seconds for the speakers to link.
Note : Speakers should be within 50’ (15 m) of each other to properly link. The closer the speakers are, the faster they will link.
Note : To exit Stereo-LinkTM mode, double-press the Bluetooth button again. -
Once the speakers are linked, the secondary speaker’s Bluetooth LED will be lit solid blue, and the primary speaker’s blue woofer LEDs will spin to indicate it is searching for a Bluetooth device to pair with.
-
Navigate to your device’s Bluetooth settings menu and select Uber Boom Ultra to connect. When the connection is successful, you will hear “Bluetooth Connected” from the primary speaker (if voice prompts are enabled). When audio playback begins, you should hear it through both speakers. The primary speaker will play the left channel while the secondary speaker plays the right channel. Playback controls are active on both speakers.
-
To exit Stereo-LinkTM mode, press and hold the Play/Pause button for two seconds on one UberTM Boom Ultra. You will hear “Bluetooth disconnected” from the primary speaker to indicate the link has been broken (if voice prompts are enabled.)
Tip : UberTM Boom Ultra can sync audio with other Stereo-LinkTM- compatible ION Audio speakers. To find out more, visit ionaudio.com
Note : Pressing and holding the Power button on the primary speaker while in Stereo-LinkTM mode will power off all connected speakers. UberTM Boom Ultra speakers powered off in Stereo-LinkTM mode will automatically enter Stereo- LinkTM mode the next time they are powered on and begin searching for secondary speakers to connect to.
Bluetooth Call Answering
UberTM Boom Ultra can receive incoming calls and act as a speakerphone for connected Bluetooth devices. Incoming calls will pause Bluetooth audio and play the device’s ringtone until the call is either answered or rejected:
To reject an incoming call, Press and hold the Play/Pause button for two
seconds.
To answer an incoming call, press the Play/Pause button and then quickly
release it. During a call, press the Volume Up/Down buttons to adjust the
volume of the caller.
When you wish to end a call, press the Play/Pause button. Bluetooth audio will
resume playing at this time.
USB/SD Playback Mode
UberTM Boom Ultra can play back audio files stored on a USB drive or Micro-SD
Card. Inserting a USB drive or Micro-SD card into the corresponding port on
the rear panel will switch the unit to the appropriate playback mode. You will
hear “USB mode” or “SD mode” upon connecting if voice prompts are enabled. Use
the top panel buttons for playback control as described in Bluetooth
Connecting with UberTM Boom Ultra.
UberTM Boom Ultra will return to Bluetooth mode upon removal of the USB or
Micro-SD card unless another device is still connected.
The following file formats are supported for USB/SD playback: .ape, .flac,
.wav, .wma, and .mp3.
Connecting an Audio Device Using the Aux Input
-
Connect a 1/8” (3.5 mm) auxiliary cable to the input on the rear panel of UberTM Boom Ultra and connect the other end to an audio device such as an MP3 or CD player. The speaker will automatically switch the audio source to Aux mode but will maintain all Bluetooth connections.
-
Press play on your device’s music player. Use the Volume Up/Down buttons to adjust the Aux volume.
Note: UberTM Boom Ultra speaker volume controls act independently from your connected device. Lower the volume on your device if signal distortion occurs. -
Disconnect the Aux cable to exit Aux mode. UberTM Boom Ultra will revert to the audio mode it was in before the Aux connection, Bluetooth or USB/SD.
Karaoke Mode
In any playback mode, connecting a microphone to the 1/4” Mic Input on the rear panel of UberTM Boom Ultra will enable Karaoke Mode. Adjust the Mic Input volume using the Volume Up and Volume Down buttons. You can use your Bluetooth device to adjust audio playback volume. Unplug the microphone to return to the normal playback mode.
To adjust Mic Echo volume, press and hold the Bass Boost button for 3 seconds. You will hear a tone to indicate once Mic Echo mode is engaged. Then, use the Volume Up and Volume Down buttons to adjust the Mic Echo level. Press and hold the Bass Boost button again until the tone plays to exit Mic Echo mode and reset the volume buttons to Main Volume controls.
Note : Mic echo is not available when using Stereo-LinkTM Mode.
Light Modes
Press and quickly release the Lights button to cycle through 10 light mode selections, listed below. Press and hold the Lights button to turn the LEDs on or off at any time.
- Dual Color Cycle – Starts on Red/Orange and slowly changes colors every 3 seconds.
- Dual Color Beat-Sync – Same as Dual Color Cycle, except LEDs animate from outside to in.
- Rainbow Wheels – Full Rainbow Wheel with no beat sync; The colors of the wheel slowly rotate in a clockwise circle.
- Rainbow Beat Sync (bottom-up) – Full Rainbow Wheel; The LEDs animate from the bottom up to the beat.
- Rainbow Beat Sync (Rotation) – Full Rainbow Wheel; The colors rotate in different directions at different speeds depending on the beat.
- Rainbow Chase (wheels) – Partial Rainbow Wheel; The LEDs animate around in a circle clockwise.
- Rainbow Chase Beat Sync (wheels) – Partial Rainbow Wheel; The LEDs animate around in a circle and speed along with the beat.
- Rainbow Chase (Figure 8) – Partial Rainbow Wheel; The LEDs animate around one circle and then cross over to the other at the midpoint.
- Rainbow Sweep (Left to Right) – Mirror image Rainbow Wheel; LEDS turn on from left to right in a sweeping motion.
- Single Color – Will default to Orange. Users can adjust the color and brightness in the ION Sound XPTM app.
- Off.
Troubleshooting
If the unit is not charging: Make sure the USB-C cable is properly connected
to the power input, the power adapter and the power outlet.
If the sound is distorted: Try lowering the volume control of your sound
source.
If there is too much bass: Try adjusting the tone or EQ control on your sound source to lower the bass level. This will allow you to play the music louder before clipping (distortion) occurs. You can also check to see if the Bass Boost function is enabled, and disable it by pressing the Bass Boost button to disable it.
If you cannot connect your audio device to UberTM Boom Ultra via Bluetooth:
- Have your audio device (e.g., smartphone or tablet) and UberTM Boom Ultra as close together as possible while trying to connect. Make sure both the audio device and UberTM Boom Ultra are unobstructed by walls, furniture, etc.
- Press and hold the Bluetooth button to disconnect UberTM Boom Ultra from any other audio device and restart the search process. If this does not work right away, power off UberTM Boom Ultra and then power it back on. See Bluetooth Connecting with UberTM Boom Ultra for more information.
- Reset the Bluetooth connection on your audio device by turning Bluetooth off and back on. You can find this under the Bluetooth menu in the Settings for your phone or other audio device.
If this does not work, and you have connected to UberTM Boom Ultra before, find UberTM Boom Ultra in the list of available or previously connected devices in your audio device’s Bluetooth menu, tap the “gear” or “i” icon located next to it and then select Unpair or Forget. Turn UberTM Boom Ultra off and back on and try pairing again once it reappears in your available devices list.
Note : If UberTM Boom Ultra has been paired to another audio device recently that is still within range, you may need to repeat this process with that audio device to fully disconnect.
If you experience audio dropouts while playing music from a Bluetooth device, this may be happening because your unit is trying to link to another speaker. This can occur if you power off a speaker that was linked to your unit or if you have just turned on your unit and it is in Stereo-LinkTM mode. To stop the audio dropouts, exit Stereo-LinkTM mode by pressing the Bluetooth button. Alternatively, you can wait for your unit to link to another speaker if there is one within range.
If you would like to stop your speaker from automatically linking when you power it on, make sure you press and hold the Play/Pause button for two seconds to exit Stereo-LinkTM mode before you power it off.
Technical Specifications
Output Power | 80 W (peak) |
---|---|
Frequency Response | 115 Hz – 15 kHz |
Drivers | 2 x 3.5” (89 mm) |
Bluetooth Specifications | Profile : A2DP, AVRCP |
Bluetooth Version: 5.0 | |
Range : Up to 100 ft. (30.5 m) * | |
Stereo-Link TM Range: Up to 100 ft. (30.5 m) between | |
speakers | |
Battery | Battery life : Up to 12 hours (at 30% volume, lights off) |
**
Charge Time : Up to 4 Hours (using 5V, 2A USB power adapter)
Dimensions
(width x depth x height)
| 14.25″ x 6.10″ x 7.80″
362 mm x 155 mm x 198 mm
Weight| 4.86 lbs.
2.21 kg
Specifications are subject to change without notice.
- Bluetooth and wireless reception and range are affected by walls, obstructions, and movement. For optimal performance, place the product so it is unobstructed by walls or furniture and is raised off the ground.
- Battery life may vary based on temperature, age, and volume usage of product.
Trademarks & Licenses
ION Audio is a trademark of inMusic Brands, Inc., registered in the U.S. and
other countries.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any
use of such marks by ION Audio is under license.
App Store is a trademark of Apple Inc., registered in the U.S. and other
countries.
Android and Google Play are registered trademarks of Google Inc. All other
product names, company names, trademarks, or trade names are those of their
respective owners.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>