Kwikset 52436-001 SmartCode 260 Keyless Electronic Keypad Deadbolt Instruction Manual

: June 14, 2024
: Kwikset

Table of Contents

52436-001 SmartCode 260 Keyless Electronic Keypad Deadbolt
Parts in the box
Required tools
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

52436-001
Rev 04
SMART CODE
EYPAD ELECTRONIC LOCKS

Quick Start Guide

52436-001 SmartCode 260 Keyless Electronic Keypad Deadbolt

Welcome to the Kwikset family!
This guide will get you up and running with your new SmartCode™ Lock.
If you have any issues, please visit our support center: kwikset.com or call us at 1-800-327-5625.

Parts in the box

Required tools

Philips screwdriver
No electric drills

Installation

! Remove your existing deadbolt and strike

If drilling a new door, use the supplied template and instructions available at: kwikset.com/doorprep

Install the latch
Install the strike

3.1 Install the exterior assembly

3.2 Install the interior assembly

4. Install the AA batteries

5. Add a User Code and install cover

Before you can lock or unlock the door a User Code must be created.
Refer to page 19 for instructions on how to create a User Code.

Locking
To lock your door, press the Lock button. The lock will beep and the
keypad will flash amber as the bolt extends.| Unlocking
To unlock your door, enter the User Code. The lock will beep and the keypad will flash green and beep twice as the bolt retracts.
---|---
|

SmartCode™ at a Glance

1. Lock Button
Used for programming, clearing User Code entry errors, lighting up the keypad and locking the door.
2. Number Buttons
Used to enter User Codes. Each code must be 4 to 8 digits in length.
3. SmartKey Cylinder
Rekeyable cylinder retracts and extends the latch bolt by key from the exterior.| 4. Battery Holder
Uses 4 AA Alkaline batteries, 1.5V
5. Programming Button
Used for programming functions.
6. Turnpiece
Lock and unlock from the interior.
7. Battery Cover
Push it upward and outward to replace the batteries.
---|---

SmartKey Re-Keying
Re-key the lock to work with your existing key. See the supplied
SmartKey Re-key instructions for more information.
Note: If Auto-Lock is enabled, remove the batteries before re-keying your lock.

System Alerts

Operation	Lights	Sounds	Explanation
Unlock	Flashes GREEN x2	2 beeps	Successful unlock
Flashes RED x10	10 beeps	Low battery	Install fresh new batteries
Flashes RED x 3	3 beeps	Incorrect User Code	Check code. and retry
Flashes RED x15	15 beeps	Exceed 3 incorrect User Code attempts	Wait 1

Programming
Ensure the door is open before performing any programming.
The programming button is located on the interior chassis below the battery holder (refer to page 17). During programming, if no button is pressed within 5 seconds, the system will time out and you will need to restart the procedure.

Add User Code (UC)	Programming Button 1 enter UC

Delete Individual
User Codes (UC)| Programming Button 2 enter UC to delete
enter UC to delete
Add/Change
Programming Code
(PC)| Programming Button 3 enter PC
Delete all User Codes| Programming Button 4 4
Enable/Disable Audio| Programming Button 5
Enable/Disable User Codes| Programming Button 6
Add One-time User Code| Programming Button 7 enter one-time UC
Change Auto-Lock Time Delay| Programming Button 8 press button for delay
1. 30 seconds 2. 1 minute 3. 3 minutes 4. 5 minutes 5. 10 minutes
Enable/Disable Auto-Lock| Programming Button 9
Door Rehanding| Programming Button 0
Factory Reset (lock must be in unlocked position)| Press and HOLD Programming Button for 15 seconds Programming Button again

Programming Notes

Add User Code:
Up to 50 User Codes can be saved. User Codes should be 4 to 8 digits in length.
For security reasons, the first 4 digits of each User Code must be unique. For example, you are unable to program a User Code 1-2-3-4-5 as well as a User Code 1-2-3-4-6.
Press the lock button before entering your code to light up the keypad at night.

Enable/Disable Programming Code:
Optional: A Programming Code enables you to make programming changes without needing to access the programming button. This is ideal for landlords to allow programming from the outside without access to the interior programming button.
One Programming Code can be saved and should be 4 to 8 digits in length. The Programming Code can not be the same as any User Code and will not unlock the lock.
To program the lock when the Programming Code is enabled, instead of pressing the programming button, enter the Programming Code, press the lock button and proceed with the remaining steps on page 19. Repeat the programming steps to disable the Programming Code. Please note once a Programing Code is enabled, the programming button is disabled and can only be used to factory reset the lock.

Delete All User Codes:
Keypad locking function will be disabled when User Codes are deleted. The lock can only be operated manually by key during this time.

Enable/Disable Audio:
LED status indicator will still function once audio is disabled. Repeat the programming steps to enable the audio.

Enable/Disable User Codes:
When all User Codes are disabled, all electronic functions will be disabled as well. The door must be locked or unlocked manually with the key. Repeat the programming steps to enable the User Codes.

Add One-Time Use Code:
Up to 10 One-time User Codes can be saved. One-time User Codes should be 4 to 8 digits in length. The One-Time User Code will be deleted automatically after it is used. The same One-Time User Code can be created again after it’s used.

Change Auto-Lock Time Delay:
Press the keypad number that corresponds to your time delay preference:
“1”: 30 seconds “2”: 1 minute “3”: 3 minutes “4”: 5 minutes “5”: 10 minutes

Enable/Disable Auto Lock:
The default setting is disabled. Once you enable auto-lock the default setting is set to 30 seconds.
To change the auto lock time delay, see the “Change Auto-Lock Time Delay” programming step.
Repeat the programming steps to disable auto-lock.

Door Rehanding Identification:
Perform this process for the lock to learn the locking and unlocking direction of the door.
This feature is used for the lock to learn the orientation of your door (left- or righthanded). If stuck/jammed bolt error continues to occur after performing this step, please make sure there is no obstruction from strike or door jamb to prevent the bolt from extending.

Factory Reset:
A factory reset will delete all User Codes and change all programming to factory settings.

Important Safeguards

Read all instructions in their entirety.
Familiarize yourself with all warning and caution statements.
Remind all family members of safety precautions.
Always have access to your lock’s standard key.
If using the Auto-Lock features, make sure you have your smartphone or standard key with you to prevent locking yourself out.
Familiarize yourself with the system alerts.
Replace low batteries immediately.
Dispose of used batteries according to local laws and regulations.

WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.
CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the User Codes, you must restrict access to the back panel and routinely check the User Codes to ensure they have not been altered without your knowledge. The use of a programming code can help protect your system’s settings.

Regulatory Compliance

This product complies with standards established by the following regulatory bodies:

Federal Communications Commission (FCC)
Industry Canada

FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ( 1 ) this device may not cause harmful interference, and ( 2 ) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT! Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: ( 1 ) This device may not cause interference, and ( 2 ) This device must accept any interference, including interference that may cause undesired operation of the device.