VEVOR FLO300 Macerator Pump Instruction Manual
- June 14, 2024
- VEVOR
Table of Contents
VEVOR FLO300 Macerator Pump
Important Information
We continue to be committed to provide you tools with competitive price. “Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you’re actually saving half in comparison with the top major brands.
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation four user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform again there are any technology or software updates on our product.
Kindly Reminder
The FLO300 has been developed with
the utmost care and it is tested in the factory.Therefore, it is possible that
the test water remains in the appliance.
INSTALLATION REQUIREMENTS
This appliance must be earthed.
If the supply cord is damaged, it must be replaced by a qualified person. The cable type is SJT 18AWGx3C. The IP rating of this appliance is IPX4. Water: The unit is gravity fed from the washing machine, shower, etc. with a built-in pressure switch that detects the incoming waste and starts the pump.
The outlet comes as standard with a 1-1/4″ (32 mm) connection, however, 1″ (28 mm) can be used with a reducer. If using bends in connecting pipework, ensure they are smooth curves to avoid blockages. Besides, never use a 90-degree bent, but a 45-degree bent.
SPECIFICATIONS
The water temperature should be a minimum of 1℃ for it is important that the unit does not freeze, and a maximum water temperature is 90℃.
| Input Power Rating: | 350W | Max Vertical Lift: | 7M |
|---|---|---|---|
| Input Voltage: | 115V, 60HZ | Max Temperature: | 90℃ |
| Flow Rated: | 100 L/MIN | Noise Level: | 45 dBA |
| Max Horizontal Lift: | 70M | Degree of Protection: | IPX4 |
INSTALLATION GUIDANCE
- Accessories list
| 
| 
| 
---|---|---|---
Check Valve
|
Rubber Tube
|
Snap hoop (32mm-50mm)
|
Snap hoop (20mm-32mm)
-
Install the check valve at the outlet. Tighten with the snap hoop (accessory D). Remove the choke plug from the product, install the rubber tube (accessory B), and tighten it with the snap hoop (accessory C). The outlet pipe is 3/4″ (1″ and 1-1/4″ are also good choices), and inlet pipes are 1-1/2″.
-
The other side of the product has two water inlets, which are covered with a choke plug. When installing, the arrow on the chokeplugisdownward, then the plug can be pulled out. Then install thesnaphoopetc. Unused water inlets should be covered with choke plugs, and direction of the arrow should be turned to other directions.
-
Notes and installation diagram.
For wastewater from the shower and bath, ensure that the slope of the siphon is at least 1% (0.4 inches per 40 inches) so that the wastewater flows through the natural gravity to the unit position.
If other sanitary units are connected to the disposal line along the disposal circuit, install check valves in the appropriate waste pipes to prevent backflow.
The slope of the horizontal components must be at least 1%.
Note: Discharge pipe length to the first elbow should be a minimum length of 1.6
-
If installing underground, the method is as follows:
TROUBLE SHOOTINGS
Some malfunctions of the grinder are not practically serious. You Can Correct it by yourself. To diagnose and find a solution to the Trouble, refer to the diagram below. For other malfunctions, contact the supplier or qualified professional.
| MALFUNCTIONS | POSSIBLE CAUSES | SOLUTIONS |
|---|---|---|
| The appliance occasionally starts to work | The connected pipelines are | |
| leaking | Check the installation in front of the appliance | |
| The check valve is leaking | Clean or replace the check valve | |
| The motor is running properly, but the water runs slowly away. | The aerator in | |
| the lid is blocked | Clean the aerator | |
| The engine is running properly but non-stop or runs for a long time | The |
height or length of the drain is too large, or too many bends are used(power
failure)| Check the installation
The pump is blocked| Turn off the power, disassemble the pump and unblock
The motor is not switched on| The power supply is not switched on| Switch the
on power supply (repeat)
The plug is defective| Repair the plug
The trouble with the motor or sensor| Remove the lid, flush clean, and dry the
sensor up(hair dryer)
The motor rattles with a noise| There’s a strange object in the motor| Remove
the lid, clean it and remove the object
The motor is buzzing and does not rotate| The condensator is broken or has
trouble with the motor| Get in contact with a qualified specialist or the
supplier
There’s a strange object in the Remove the lid, clean it and motor| Remove the
lid, clean it and remove the object
Manufacturer: Ningbo YUNSUN Electromechanical Co., Ltd
Address: Building 3 No.7 Hongshen Road Hongtang Industrial Zone A, Jiangbei District 315033 Zhejiang P.R. China
Made In China
Customers Support
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us: CustomerService@vevor.com
Technical Support and E-Warranty Certificate www.vevor.com/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>