ABUS PPIC90000 Battery Cam and Base Station User Guide

ABUS PPIC90000 Battery Cam and Base Station

SYSTEM REQUIREMENTS

• 2,4 GHz Wi-Fi network with password and encryption.

• The WLAN password must not exceed a length of 31 characters.

• The following special characters are not possible when entering the Wi-Fi password.

• The following special characters are possible when entering the Wi-Fi password.

• Place the base station within the range of your home network/ WiFi.
• Place the Battery Cam within the range of a base station.
• Max. two cameras per base station and max. 8 base stations per app.
• The site service of the mobile end device must be activated.
• The camera can only be used in conjunction with the App2Cam Plus.
• Routers with a 5 GHz frequency and networks without encryption are not supported.

SCOPE OF DELIVERY

• 1x Installation material
• 1x USB plug-in power supply
• 1x Removal aid for the microSD card
• 1x Wall bracket
• 1x Micro USB cable

ABUS Wi-Fi base station for battery cam (PPIC90010)

• 1x USB plug-in power supply
• 1x Removal aid for the microSD card for the microSD card

ABUS Wi-Fi battery cam 2-set with a base station (PPIC90200)

• 2x Installation material
• 2x Wall bracket
• 1x USB plug-in power supply
• 1x Removal aid for the microSD card
• 1x Micro USB cable

ABUS Wi-Fi additional battery cam (PPIC90520, PPIC90520B)

• 1x Installation material

• 1x Wall bracket

• 1x Micro USB cable

• Before switching on and initial start-up: Charge the camera’s integrated battery using the micro USB cable and the USB power adapter until the red LED on the back of the camera lights up continuously.

• Then disconnect the cable. Do not switch on the camera yet.

CAMERA

• Wireless frequency: 2.4 GHz (802.11 b/g/n) max. transmission power 20 dBm

MAIN UNIT

Increasing the range/signal strength
An additional base station can be used if, for example, two cameras assigned to one base station are positioned too far apart in a larger building. In this case, a second base station can be installed close to the second camera and the camera can be assigned to this base station.

A standard microSD card (max. 128 GB storage capacity / min. Class 10) is required for recording. The camera must be disconnected from the PSU in order to insert and remove the MicroSD card. The microSD card audibly snaps into place when fully inserted. The provided removal aid can be used to remove the card.

OPERATION AND DISPLAY ELEMENTS

Charge the camera’s built-in battery, if not already done, using the micro USB cable and USB power adapter until the red LED on the back of the camera lights up continuously. Then disconnect the cable. Switch on the camera first during start-up, as described below.

• Ready for connection (pairing): Press and hold the pairing key for 3s until the status LED flashes blue.
• Reset to factory setting: Press and hold the reset key for 5s until the status LED flashes red.

Switching on the camera: Press the button once briefly.

• Pairing function: Press the button three times briefly.
• Switching off the camera: Press and hold the button for 5 seconds.
• Do not apply power to the base station until startup, as described below.
• The base station establishes a connection to the camera during startup. In very rare cases, no connection is established and a factory reset may be necessary.

COVERAGE A RE A O F THE SENSOR

• The detection range of the integrated motion sensor (passive infrared technology, PIR) is limited to 8m.
• People who are outside of this range are “seen” by the camera and displayed on the live image, but do not trigger a recording.
• The recommendation for an optimal mounting height is 2m and an inclination angle of 12.5°.

Installation height (m) and inclination angle (°)

INITIAL START-UP

Installation of App2Cam Plus and start-up

• Launch App2Cam Plus and select “Add new device” to start the start-up.

• The same steps for startup also show a support video: l.ead.me/bd9jIA

Option 1: Scan the QR code on the back of the base station.

Option 2: Select your camera model.

• If the base station is powered, please disconnect it from the power supply.

• Click on “Next” to continue with the installation.

• The following illustrations are from the iOS app.

• The process with the Android app follows the same steps.

• For optimal startup, the base station and the smartphone/tablet must be as close as possible next to each other, at a maximum distance of 3 meters.

• Connect the base station to the USB power supply and supply it with power.

• The base station is ready for use after 45 seconds as soon as the voice output occurs: “Ready to connect to the network”.

• Then tap “Switch to Wi-Fi settings” in the app.

• Select the WLAN network of the base station; its name starts with “HD”.

• The password for the WLAN network of the base station is: 12345678.

• Confirm the entry with “Connect”.

• The site services must be activated in the settings of your smartphone for optimal operation.

• Switch back to App2Cam Plus. The app now indicates that an initial connection between the app and the base station has been successfully established. Tap on “Next”.

• Turn on the camera by pressing the power button on the back of the camera once. The red LED on the back of the camera flashes. Confirm in the app with “Next”.

• Select your home network/WLAN, where you want to operate the camera permanently.

• Then tap on “Next”.

• The integrated camera battery must be charged at this time.

• See system requirements 2,4 GHz network“ and „special characters“

• Enter the password of your network.

• Then tap on “Next”.

• Now assign a security code and a separate admin password.

• Code and password must NOT be identical during commissioning.

• Then tap on “Next”.

• The base station will now restart. Wait for the countdown until the voice output occurs: “Successfully connected to the network”.

• Then confirm the information about the firmware update.

• The admin password can be changed in the camera settings after installation.

• You can find additional steps for the „Alternative installation“ in the operating instructions.

• Delivered from the factory or in a common set package (PPIC90000, PPIC90000B, PPIC90200), the camera(s) and base station are already paired/connected; in this case, skip steps 14 and 15.

• Steps 14 and 15 are only to be performed if the items/components were purchased individually or independently of each other, i.e. usually after the purchase of an additional base station (PPIC90010), or an additional camera (PPIC90520, PPIC90520B).

• Press the pairing button for at least 3 seconds until the status LED flashes blue.

• In addition, the voice output occurs: “Ready for camera connection”

• Switch on the camera by pressing the power button 1x, so that the red LED on the back of the camera lights up. Then press the On/Off key 3x briefly, to teach the camera. As soon as the camera and base station are connected, the base station outputs the voice message: “Camera connection successfully completed”.

• An additional base station can be used if, for example, two cameras assigned to one base station are positioned too far apart in a larger building. In this case, a second base station an be installed close to the second camera and the camera can be assigned to this base station. Two cameras can be operated from one base station. Up to 8 base stations are supported by the app.

• Now tap the image icon with the two arrows or the preview to display the first live image from your camera.

• You have successfully completed the start-up.

• All settings and functions can be called up via the menu bar at the bottom of the screen.

To make personal settings on the camera camera

1. tap the menu icon in the menu bar at the bottom of the screen.
2. Now tap on the icon with the two gearwheels at the top of the camera bar. on the icon with the two gearwheels

APP2CAM PLUS

The live view in App2Cam Plus

• The screenshots and icons shown here are from the iOS app.
• There may be some deviations in the labels, design or functionality when using Android devices.

CAMERA INSTALLATION

Option A: Installing the camera without a wall bracket

The camera can also be set up without a wall bracket on a flat surface.
The following aspects must be observed here:

• The position of the camera is not fixed during setup and could be accidentally shifted, thus changing the recording area.
• Large objects located between the camera and the base station could impact the transmission.
• Where possible, the camera should be positioned unobstructed at the edge of the setup surface in order to prevent light reflections between the camera and the setup surface.
• The camera‘s field of vision must not be obstructed by objects.
• Positioning the camera on a glass shelf could lead to interfering reflections during recording.

Option B: Installing the camera with a wall bracket

Ensure that the Wi-Fi signal of your home network is sufficiently strong and stable at the desired location for continuous smooth operation. If necessary, first start up the camera base station and then test the reception at exactly the positions you have planned for the camera and the base station. For more information on signal strength, please refer to the user manual.

The Quick Guide, the complete operating instructions and further information are available on the ABUS website: Simply scan the QR code or enter the web address to open the product page with the Downloads section.

• abus.com/products/PPIC90000.
• abus.com/products/PPIC90000B.
• abus.com/products/PPIC90010.
• abus.com/products/PPIC90200.
• abus.com/products/PPIC90520.
• abus.com/products/PPIC90520B.

CONTACT

• Linker Kreuthweg 5
• 86444 Affing
• Germany
• Tel: +49 8207 959 90-0
• Fax: +49 8207 959 90-190
• info.de@abus-sc.com.
• ABUS | Security Center GmbH & Co. KG
• abus.com.

References

• ABUS - Security technology since 1924
• YouTube
• Standard Chartered Bank

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>