ABUS AZBW10000 Motion detector PIR (PET) User Guide
- June 5, 2024
- ABUS
Table of Contents
QUICK
GUIDE
AZBW10000
Disassembling the Detector
| Lens | PCB |
|---|---|
| LED Light Pipe | Nut |
| Lens holder | Casing Screw |
Printed Circuit
Board (PCB)
| PIR Sensor | Tamper Spring |
|---|---|
| Tamper Resistor Headers | LED ON/OFF |
Terminals| Sensitivity Settings
Alarm Resistor Headers|
Installation
Detector Backplane Installation
Screw Model: PA_3.5 ×25
Number: 4
Installation Hints
Environmental Class (EC) II
ABUS Security Center
GmbH & Co. KG
Linker Kreuthweg 5
86444 Affing
Germany
abus.com
The Lens
Detection Range 85.9° 52 zones 4 planes| To use the pet immunity function,
please install a pet mask.
---|---
Mounting height range from 1.8 m to 2.4 m.
Note: PET immunity is available up to 10 m and at a height that is below
the top plane of view| Pet Table| Sensitivity mode| Weight
---|---
High| 5 kg
Auto| 10 kg
Low| 15 kg
Resistor Wiring
The detector has two methods for resistor wiring:
(1) Using headers to select the End of Line resistance (Control panel
dependent) on the ALARM/TAMPER header pins.
(2) Select a resistance (Control panel dependent), and add the resistor to the
ALARM/TAMPER wiring ports of the detector.
Note: If EOL (End of Line) wiring is not used, leave the headers OFF. If the headers and the header pins do not match, do not force the header, please select method 2 to wire the resistor.
Method 1 and method 2 should not be used on the ALARM/TAMPER at the same time.
| 
---|---
Alarm Resistance: 1K, 2K2, 4K7, 5K6, 8K2
Tamper Resistance: 1K, 2K2, 4K7, 5K6
1
Normally Closed
2
3
Double End of Line Wiring
The connection shows the example:
- Normal: 1K
- Alarm: 2K
- Tamper: 0 Kor infinite
4
Choose the Connection Type
| A | B |
|---|---|
| Alarm Control Panel | Detector |
Two Double End of Line Detectors to One Input.
Powering up
Powering up:
After powering on, the indicator flashes rapidly. Once the detector self-test
is completed, the LED indicator will go out until the detector detects
movement
Dimension and Weight
Technical Specification
| Detection range | 16 m, 85,9° |
|---|---|
| Detection speed | 0.3 ~ 2 m/s |
| Sensitivity | High, Auto, Low |
| Auto sensitivity | Yes |
| Onboard EOL | Yes |
| Digital temperature compensation | Yes |
| Technology | Digital microprocessor-based |
| Sealed optics | Yes |
| Creep zone protection | Yes |
| Tamper protection | Front |
| LED indicators | Blue(alarm) |
| Pet immunity | See PET Table |
| Power supply | 9 to 16 VDC (standard: 12 VDC) |
| Current consumption | 11mA quiescent, 8mA Alarm |
| Operating temperature | -10 °C to 55 °C (14 °F to 131 °F) |
| Storage temperature | -20 °C to 60 °C (-4 °F to 140 °F) |
| Operating humidity | 10% to 90% |
| Mounting height | 1.8 – 2.4m |
| Dimensions (HxWxD) | 86,8 mm x 65,4 mm x 45,5 mm |
| Weight | 68 g |
DECLARATION OF CONFORMITY
ABUS Security-Center hereby declares that the enclosed product(s) comply with
the requirements of the following directives: EMC Directive (2014/30/EU) and
RoHS Directive (2011/65/EU). The full EU
Declaration of Conformity text can be found at:
www.abus.com/product/AZBW10000
It can also be obtained at the following address:
ABUS Security Center
GmbH & Co. KG, Linker Kreuthweg 5, 86444 Affing, GERMANY
Subject to technical modifications and color changes. No liability is assumed
for mistakes or printing errors.
References
- ABUS - Security technology since 1924
- ABUS Wired Motion Detector (AZBW10000)
- ABUS Wired Motion Detector (AZBW10000)