ESYLUX EM10025358 Motion Detector Defensor User Guide

: June 14, 2024
: ESYLUX

Table of Contents

SHORT INSTRUCTION
Intended use
Installation
Connection
Initial operation
Settings
Technical data
Disposal / warranty
Documents / Resources

**ESYLUX EM10025358 Motion Detector Defensor User Guide

**

SHORT INSTRUCTION

DANGER!

Risk of fatal injury from electric shock!
Installation must only by performed by an electrical installation technician or a trained electrician, taking country-specific regulations into account
Switch off the mains voltage prior to assembly / disassembly
Protect the device with a 10-A circuit breaker
μ = contact opening width < 1.2 mm

Intended use

Operating manual:

https://www.esylux.com/products/outdoor-automation/motiondetectors/defensor
https://www.esylux.com/y/MA017081 (QR-Code top left)

The motion detector is a passive infrared detector with a 200° / 230° / 280° field of detection: diagonally (A), frontal (B), 360° creep protection (C).

The motion detector is designed for outdoor use and requires an unobstructed view of heat sources (people, vehicles)

Automatic light control depending on the preset brightness switching value and switch-off delay time
Anti-vandal protection (MD 230 / MD 280)
With zero-cross switching for load-free switching of the connected devices

Installation position (1.1)
Wall (MD 200 / MD 230 / MD 280)
Ceiling (MD 230 / MD 280)
Included in delivery
1 x motion detector, 1 x lens mask
Accessories (optional)
Corner bracket, spacer, ESY-Pen

Installation

The device is installed as shown in figures (2.1 – 2.3).

Consider the local conditions, e.g. neighbouring properties or the distance to the road
Ensure connected lighting is mounted with sufficient clearance from the motion detector or is mounted above it to avoid any interference with the light sensor. Do not point light sources directly at the motion detector

Connection

Connect as shown in the following figure (3.1). Standard with optional control via a closing button and parallel wiring of max. ten devices

L External conductor 230 V ~
L ’ Switched external conductor 230 V ~
N Neutral conductor
S Push button

Initial operation

Connect the power supply
A warm-up phase of approx. 45 seconds is initiated. The sensor LED flashes blue, red, red alternately. During this time, the lighting is switched on. The motion detector is then ready for use

Settings

The motion detector is delivered with the factory settings / in fully automatic mode

Brightness switching value: 20 Lux
Switch-off delay time: 5 min.
Sensitivity: 100 %
Sensor LED feedback : on
Password: 0000
Creep protection (MD 230 / MD 280) : on

Parameterisation and control via the ESY-Pen and the free ESY Control app (4.1), REMOTE CONTROL (EM10025501), REMOTE CONTROL USER (EM10025495).
Note: For optimal signal transmission, observe the minimum distance corresponding to the installation height. Direct sunlight can prevent the signal from being transmitted.
Control via push-button only possible for functions “Manual light on/off” and “Light 4 h/12h on/off”.

Information on the scope of functions can be found in the operating instructions of the respective product at www.esylux.com.

Technical data

Power consumption	< 0,5 W
In-rush current	max. 800 A/200 µs
Switching capacity	230 V ~ / 50 – 60 Hz 2300 W / 10 A (cos φ = 1) 1150 VA / 5

AX (cos φ = 0,5)
Connection| NYM 3 x 1.5 mm² … NYY 5 x 2.5 mm² Ø min. 2 x 9 mm … Ø max. 2 x 15 mm
Weight| MD 200 228 g MD 230 260 g MD 280 260 g
Material| UV-resistant plastic
Colour| white, similar to RAL 9003 graphite grey, similar to RAL 7024

Disposal / warranty

This device must not be disposed of as unsorted residual waste. Used devices must be disposed of correctly. Contact your local town council for more information.

The ESYLUX manufacturer’s warranty can be found online at www.esylux.com.

Technical and design features may be subject to change.

Technical data for specific products can be found at www.esylux.com/products

Symbol

Item no.| Product name A B C H em em ern m| H max.
m| X
mm| Y
mm| Z
mm
---|---|---|---|---|---
EM10025358| DEFENSOR MD 200°24 IRIC IP55 WH| 24| 8| | 3| 5| 92| 108| 108
EM10025365| DEFENSOR ]MD 200°24 IRIC IP55 AN| 24| 8| | 3| 5| 92| 108| 108
EM10025372| DEFENSOR MD 230° 40 IRK IP55 WH| 40| 10| | 3| 6| 92| 138| 108
EM10025389| DEFENSOR MD 230° 40 IRK IP55 AN| 40| 10| | 3| 6| 92| 138| 108
EM10025396| DEFENSOR MD 280°40 IR IC IP55 WH| 40| 10| | 3| 6| 92| 138| 108
EM10025402| DEFENSOR MD 280°40 IRIC IP55 AN| 40| 10| | 3| 6| 92| 138| 108

Dimension
1.1
MD 230 / 280
Product Instruction
with accessory

2.1
Screw hole compatible with:
A RCI series
B conventional recessed box

ESY-Pen EP10425356

ESY Control-App

Documents / Resources

| ESYLUX EM10025358 Motion Detector Defensor [pdf] User Guide
EM10025358 Motion Detector Defensor, EM10025358, Motion Detector Defensor, Detector Defensor, Defensor
---|---