EVOLAND U1210 Vibration Plates User Manual

EVOLAND U1210 Vibration Plates

Precautions

Welcome to use this body shaping machine. For your safety, please read the following carefully before use:

1. Please read this manual carefully before installation and use.
2. Warm up before use. It is strictly forbidden to dismantle the body shaping machine by yourself. Please make sure the socket voltage meets the 220V/50Hz standard before use.
3. This product has no transformer. It must be used with a special type of grounding wire socket. Do not share it with other electrical appliances. The power supply circuit must provide 6A current.
4. This product should be installed and used on a clean indoor floor. Do not use it for more than 20 minutes.
5. Do not move when using the body shaping machine. Please turn off the power after use.
6. Check the appearance of the product and the operation of each part before use. If there is any abnormality, please turn off the machine immediately and contact the dealer or our service center.
7. Do not use this product when the machine is malfunctioning (especially if there is a problem with the power cord).
8. Children or people with mobility impairments must use it under supervision.
9. Patients with heart disease, diabetes, kidney disease, liver disease, cancer or osteoporosis should consult a doctor before use.
10. Trauma patients, women during pregnancy and menstruation are prohibited from using.
11. This product is designed for home (indoor) use, if it is used in a professional fitness facility, we provides paid maintenance service in the event of a malfunction.

Product introduction

1. Ergonomic design, novel appearance, intelligent display, display time and speed.
2. 99 speed variable vibration, preset 10 slimming modes to meet the needs of different groups of people.
3.  Adopt efficient and stable silent motor.
4. Three-layer insulation material, high-precision feedback system, overheating automatic power-off, intelligent multiple circuit protection.
5. Versatility: can be used on the arms, waist, hips and legs.
6. Ergonomic design, physical healthy way to shed fat.
7. Non-slip fixed suction cup, does not hurt the floor.

Precautions

• Product Name : Power plate

• Product Size : 543213.5CM

• Carton size: 57.54216CM

• N.W./G.W. : 9.5KGS/11KGS

• Made in China

• Speed: 99 Level
  

• Start/Stop: After plugging in the product and turning on the power, push this key to start up the product. When the product is working.one can push this key to stop its running

• Time-: Time decrease: The default working time is 15 minutes. divided into 15 levels, press this button to decrease time

• Time+: Time increase: The default working time is 15 minutes. divided into 15 levels. press this button to increase time

• Speed-Speed decrease: Manual 1-99 Level. press this button to decrease the speed when the machine is operating

• Speed+Speed increase: Manual 1-99 Level, press this button to increase the speed when the machine is operating Auto/mode: Default to manual mode(HR),automatic mode is activated once pressing this button. press the button repeatedly to cycle through P1 ,P2,P3 …. P5and HR
  In the manual mode, the standby can adjust the time. the speed is not adjustable. when operating, speed adjustable, but time is not adjustable. In automatic mode, Speed and time are both not adjustable
  

Parameter Description

1. Press the power button for 5 seconds to enter the setting mode.

2. In the setting mode, press the “P” button to switch between the lowest speed setting (L) and the highest speed setting (H), when L flashing, indicating the lowest speed setting, press (time)+ – to set the value.
   When H flashes, indicating the highest speed setting, press (time)+ – to set the value
   Note: The highest speed setting (H) must be higher than the minimum speed setting (L}

3. Press the shutdown button to save the parameters and exit the setup mode.

Instructions

1. Stand on the body shaping machine and press” Start/Stop button on the remote control to activate.
2. Refer to the button description for the specific operation of the remote control.
3. Description of the stance of the three major vibration zones: Select the right zone, walk, jog, or run. You only need to adjust the distance between your feet to change the intensity of your exercise and enjoy the slimming experience brought by different methods.
4. Non-standing position instructions: Before use, you must select the low speed mode, and then adjust according to your needs to avoid the body discomfort caused by too fast speed.
5. Do not use the machine for more than 20 minutes to avoid excessive exercise and exceed the body load.

The program has 5 modes of exercising.
Intelligent conversion speed (automatic timing 15 minutes)

Motion posture description

This machine can completely relax your body and mind, relieve the soreness, eliminate fatigue, reconcile the blood, improve the circulation of the body, promote the decomposition of fat, and develop a slim body. A few people may have dizziness, stomach discomfort, itchy skin and red tide during the initial use, which are normal, you just need to take a break.

| Sit sideways
Sitting on a chair, lightly step on the machine ,and relax yourself. This posture is mainly to exercise the calf muscles.
---|---
| Leg lifting
Sitting on the machine, keep your legs hanging and keep your hands in a tight state. This posture mainly exercises the leg muscles, buttocks and abdomen.
| Single leg
Place one foot on the pedal and the other leg to stand on the bottom. This posture mainly exercises the one-sided thigh and calf.
| Cross leg
Sitting on the machine with your legs crossed, put your hands on your knees, and close your eyes to relax. This posture mainly exercises the legs and buttocks.
| Stand
Stand with your legs apart, put your hands on your hips or flat, and adjust the spacing between your feet as needed. This position can exercise your body.
| Halve Squat
Bend your legs then stand on the machine, set level both hands, maintain balance in a vertical state. This posture mainly exercises the back muscles, the big muscles and the legs.
| Rear squat
The body leans back, legs on the machine, hands support the ground. This position mainly exercises the leg muscles.
| Bend legs
Stand with one leg bent on the pedal and the other leg bent on the ground. This position mainly exercises legs and hips.
| Front squat
Flatly stretch your legs backwards, hands support on the machine and make a prone position. This position mainly exercises the anns and shoulders muscles.
| Crouch
Place one foot on the pedal of the machine. Straighten your upper body and squat your legs. This position mainly exercises one-side thighs and calves.
| Sit upright
Sitting on the body shaping machine, hold the sides of the machine with both hands bent or straightened. This posture mainly exercises the legs and buttocks.

Cleaning

Machine cleaning

Be sure to turn off the power before cleaning, and make sure the power plug is unplugged. Thoroughly clean the foot pad and outer casing with a damp cloth containing detergent, then carefully wipe the cleaner with a dry cloth. (Note: Do not use corrosive and volatile cleaners containing benzene, alcohol, or gasoline; do not spill liquid into the body to prevent short circuits.)

Machine maintenance

Keep the product clean and away from high temperature and humidity. If you do not use this product for a long time, please pay attention to dust.

same fuse
The machine makes ‘beep’ sound| It is normal when working, not a mechanical fault| No need to do anything
---|---|---
The machine has no response to the remote control operation.| The remote control is dead| Replace the battery
The remote control is too far from the machine.| The effective distance of the remote control is 1.5M
Stop during use| default working time is up| Reboot
Unable to operate properly| Execute commands too frequently| Turn off the power and restart

After-sales service

This product enjoys two-year warranty. Within a limited warranty or two full years from purchase date, clients can go to the specified service points (usually contact the distributor first) to claim maintenance free service with purchase invoice or guarantee cards if there are damages caused by product’s quality.
The faults caused by accidental damage, unauthorized repair, improper storage and secondary sales of the products are not included in the warranty.

Copyright

This publication, including all photographs, illustrations and introduction images, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Trademark

AGM, the AGM logo and other AGM marks are owned by Sanzoom and may be registered. All other trademarks are the property of their respective owners.

Disclaimer

• The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
• This product specification describes the composition and respectively the properties of our product to the best of our knowledge. We make every effort to ensure that this User’s Manual is accurate and disclaim liability for any inaccuracies or omissions that may have occurred.
• If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your comments and suggestions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>