MOUNTUP AG9-21 Premium Single Monitor Desk Mount Instruction Manual

June 14, 2024
MOUNTUP

MOUNTUP AG9-21 Premium Single Monitor Desk Mount

MOUNTUP AG9-21 Premium Single Monitor Desk Mount

IMPORTANT INFORAMTION

**** WARNING!

If you have any confusions or are not quite sure about the installation, please do not hesitate to ask for our help via Amazon.

Before assembly, please check and make sure all necessary accessories are included and undamaged.
Improper installation, such as use the product for monitors over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.

The kit contains small items that could be choking hazards if swallowed. Please keep them OUT OF REACH OF CHILDREN UNDER 3 YEARS OLD.ADULT SUPERVISION IS REQUIRED.

PACKAGE CONTENTS

  • A (x1) Base

  • B (x1) Lower Arm
    PACKAGE CONTENTS

  • C (x1) Upper Arm
    PACKAGE CONTENTS

  • D (x1) VESA Plate

  • E (x1) C-Clamp

  • F (x1)  Support Plate

  • G (x1) Grommet Plate

  • H (x1) Decorative Cover

All are included in E

  • E1 Brace

  • E2 Clamp

  • E3(x2) Bolt

  • E4(x4) Bolt

Tools required

  • I (x4) Pad

  • J (x4) Bolt

  • K (x1) 3mm Allen Key

  • L (x1) 4mm Allen Key

  • M (x1) 6mm Allen Key

  • N (x2) Metal Sheet

  • M-A (x4) M4x12mm M4x25mm

  • M-B (x4) M5x12mm M5x25mm

  • M-C (x4) M6x12mm M6x25mm

  • M-D (x4) Washer D5mm

  • M-E (x8) Spacer H5mm

NOTE: Not all hardware included will be used .

DO NOT EXCEED WEIGHT CAPACITY.

Install the Base

OPTION A: For Clamp Mounting

Firstly detach Brace (E1) from C-Clamp (E) with 4mm Allen Key (L).
Mount Brace (E1) to the bottom of Base (A) by tightening Bolts (J) with 4mm Allen Key (L).

Install the Base

Apply Pads (I) to the base bottom to avoid desk scratches.
Attach the C-Clamp (E) to the Brace (E1).
Then tighten the Bolts (E4) with 4mm Allen Key (L).

Install the Base

Attach the Support Plate (F) to bolts of C-Clamp (E).
Secure stand to the desktop by tightening Bolts (E3).
Finally attach the Decorative Cover (H) to the base.

Install the Base

OPTION B : For Grommet Mounting

Mount Grommet Plate (G) to Base (A) bottom with Bolts (J) and tighten by 4mm Allen Key (M).
Apply Pad (I) to the base bottom to avoid desk scratches.

Install the Base

Detach two Bolts (E3) from C-Clamp (E) by using 4mm Allen Key (M).
Run two Bolts (E3) through Support Plate (F) and Grommet Hole on desktop, then tighten the Bolts (E3) with 6mm Allen Key (M).

Install the Base

Install the Arms

Install the Lower Arm (B) and the Upper Arm (C) to the Base (A). Secure the arm by tightening the set screws using 3mm Allen Key (K).

Install the Arms

Install the Arms

OPTION A :

If you want to rotate ±180°, just lock the lower set screw.

OPTION B :
If you want to rotate ±90°,
lock both two set screws.

OPTION A:

DO NOT tighten the screw excessively or it might be stripped.

Install the Arms

If Necessary

If metal sheet on plastic sleeve are lose, you can use spare metal sheet (N) for Installation as shown in diagram.

Attach Monitor

OPTION A : Flast back monitor

Attach the VESA Plate (D) to back of monitor and secure it with Screws (M-A or M-B or M-C) and Washers (M-D) using 4mm Allen Key (L).

**** Please make sure you don’t tighten the screws much excessively or it may cause your monitor damage.

Attach Monitor

OPTION B : For Recessed / Curved Back Monitor

Attach the VESA Plate (D) to back of monitor and secure it with Screws (M-A or M-B or M-C), Washers (M-D) and Spacers (M-E) using 4mm Allen Key (L).
Put 4 spacers between VESA plate and monitor.
Install 4 long screws through VESA plate, spacers to monitor via mounting holes.

**** Please make sure you don’t tighten the screws much excessively or it may cause your monitor damage.

Attach Monitor

Hang Monitor

HEAVY! You may need assistance with this stoip.

Hang Monitor

Hang Monitor

Note: If you want to remove the monitor, pull the lock plate back and lift the monitor to separate the monitor from the arm.

Tilt Adjustment

Problem :
If monitor faces down.

Tilt Adjustment

Solution:

  1. Slightly loosen two preassembled bolts.
  2. Adjust monitor to your desired tilt angle.
  3. Retighten both bolts to secure the monitor in place.

Tilt Adjustment

Adjust Gas Spring Tension

For intended functioning of the mount, you may need to adjust the tension of Arm (C) in accordance with your monitor weight by 6mm Allen Key (M).

Adjust Gas Spring Tension

Note 1:
Be sure to keep the arm in a horizontal position during adjustment.
Or else it would be difficult to adjust the mount or damage the mount.

Sybmol

Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.

Solution:
Turn the inside screw counterclockwise(“+”direction) to increase gas spring tension until the arm can stay as intended.

Arm falls down

Situation 2: Arm rises up
Upper Arm with monitor rises up and fails to stay where intended.
Solution :
Turn the inside screw clockwise(“-“direction) to decrease gas spring tension until the arm can stay as intended.

Arm rises up

Note 2: For how many circles the screw should be turned, please refer to the table below.

Monitor Weight| 2.21bs| 4.4 lbs| 6.6 lbs| 8.8 lbs| 11 lbs| 13.2 lbs| 15.4 lbs| 17 .6 lbs
---|---|---|---|---|---|---|---|---
Circles (AT L.EAS1)| min| 2| 3| 4| 5| 6| 7| 9
Monitor Weight| 19.8 lbs| 22 lbs| 24.3 lbs| 26.5 lbs| 28. 7 lbs| 30.9 lbs| 33.1 lbs| 35.3 lbs| 37 .5 lbs
Circles (AT L.EAS1)| 10| 11| 12| 14| 15| 17| 18| 20| 21

Route Cables along the Arm

Route Cables along the Arm

Remove the cable cover from lower arm as shown in the diagram.
Run cables through the cable cover, then insert and slide the cover down for reattachment.

Adjust as Desired

 Tilt
Swivel
Rotation
Height

Adjust as Desired

Please do not move stand outside desk for safety!

Adjust as Desired

Adjust as Desired

±90° Rotation
This function works better for monitors with the center of gravity.

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the two sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help via Amazon .

Product Dimensions

Product Dimensions

CAUTION AND MAINTENANCE:

  • Don’t allow children to climb, stand, hang, or play on any part of monitor or stand.

  • This product is intended for indoor use only. Using this product outdoors may lead to product damage or personal injury.

  • Check if that the bracket is secure and safe to use at regular intervals (at least every three months}.

  • 75x75mm / 1OQx100mm

  • 1-17kg (2.2-37.5 lbs)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals