aigostar 330200YSG Cordless Stick Vacuum Cleaner Instruction Manual

aigostar 330200YSG Cordless Stick Vacuum Cleaner

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic safety precautions should always be observed, including the following:

1. Do not use this vacuum cleaner outdoors, on wet surfaces or on cobblestones. Only use on a smooth floor such as tiles or wood.

2. Do not allow the vacuum cleaner to be used as a toy. Close attention is necessary when it is used by or near children.

3. Use the vacuum cleaner only as described in this manual. Only attachments recommended by the manufacturer should be used.

4. Do not use the vacuum cleaner if it has been dropped, damaged, left outdoors or dropped in water.

5. Do not handle the plug or vacuum cleaner with wet hands.

6. Do not put any object into the openings.
   Do not use if any opening is blocked.

7. Keep hair, loose clothing, fingers and all body parts away from openings and moving parts.

8. Do not use the vacuum cleaner to pick up anything that is burning or smoking, such as cigarettes, matches or ashes.

9. Do not use the vacuum cleaner to pick up flammable or combustible liquids, such as petrol, or in areas where such liquids may be present. 1

10. Do not use the vacuum cleaner to pick up agglomerate material, such as lime, cement, bits of wood, gypsum powder, ashes or carbon powder.

11. Do not use the vacuum cleaner to pick up sharp or hard objects, small toys, pins, paper clips, etc., to avoid damaging it and the floor.

12. Do not use the vacuum cleaner to pick up chemical substances, such as solvent, desincrustante, acidic materials and detergent.

13. Do not use the vacuum cleaner to pick up construction waste, such as dust or dinas.

14. Examine your vacuum cleaner and attend to all the labels and instructions.

15. Keep the end of the hose, tubes and other openings away from your face and body.

16. Do not use the vacuum cleaner without the dust cup filter in place.

17. Always unplug the vacuum cleaner before connecting or disconnecting it.

18. Store the vacuum cleaner indoors, and put it away after use to prevent tripping.

19. Do not use the vacuum cleaner for any purpose other than described in this user’s guide.

20. lf the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

21. Do no! block the exhaust port when vacuuming.

22. For fine dust such as flour, vacuum cleaners can only be used when the amount of dust is small.

23. Please pay attention to personal safety when using this product to clean stairs, windows and other dangerous areas.

24. Do not place the vacuum cleaner on high places such as tables and chairs or lean it on other objects to avoid damage caused by slipping or overturning.

25. The movement of the floor brush of the vacuum cleaner may cause an uneven surface gloss on waxed floors. Use a damp cloth to wipe the floor and polish with floor wax.

26. Before using, please clear the area to be cleaned of any large pieces of paper, paper balls, plastic cloth, sharp items and items with a diameter larger than the vacuum tube to prevent the suction pipe being blocked.

27. lf the motor temperature is high or there is any leakage, abnormal noise, smell or loss of suction, stop using the vacuum cleaner immediately.

28. Check the dust cup regularly. If it contains a lot of rubbish, clean it in timely fashion to ensure the ventilation opening remains unobstructed. This will prevent clogging, which causes suction to drop and the motor to heat, reducing the life of the vacuum cleaner.

29. Check the aluminium alloy pipe regularly.
    If there is any blockage, remove it in timely fashion to prevent any blockage which will cause the suction power to drop and affect the performance of the machine.

30. Do not use lubricants, detergents or polish when cleaning this product.

31. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

32. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
    • Consult the dealer or an experienced radio/TV technician for help.

33. Compliance information statement shall issue by a US Local Responsible Party.

SPECIFICATION

PRODUCT DESCRIPTION

PRODUCT ASSEMBLY

1. lnsert the tube into the port in the direction shown in the figure and make sure it is locked in place. Press the tube release button to detach.

2. Fit the floor brush into the tube. Insert the floor brush into the connecting port in the direction shown in the figure, making sure it is properly installed. Press the brush release button to detach

3. You can also insert the crevice nozzle brush into the aluminum alloy tube or directly assemble it to the main body to clean keyboards, desktops, cabinets, lamps and other items of furniture. Insert the telescopic tube assembly into the main body to clean hard-to-reach areas.

Note: You can use the crevice nozzle with or without the brush by adjusting this button.

INSTRUCTIONS FOR USE

1. Before switching the vacuum cleaner on, check the battery. If it is low, charge the machine before use. Before first use, the charging time should longer than 4.5 hours.
2. Start the vacuum cleaner by pressing the ON/OFF button on the control panel. Press it again to turn the cleaner off.
3. Press the GEAR button to adjust the speed. The vacuum cleaner starts at low speed; switch to high speed by pressing the same button again. After cleaning, switch off the vacuum cleaner.

Charging Instructions

• The charging connection is on the top of the main body. Connect the adapter and plug it in for charging to start. Please use 100-240V AC indoor charging power.

• The vacuum cleaner must use the adapter provided. Do not use any other type of adapter.

• Ensure there is no violent impact to the power adapter which might damage or affect product functions.

• Please make sure that the power adapter is kept in a dry and clean place, and do not allow it to get wet.

• Please put the power adapter in a cool and ventilated place when charging.

• Do not allow the power adapter to be in a temperature higher than 50 degrees or in the sun. Keep it away from heating and fireworks.

• If the power adapter cord is damaged, please contact the customer service for maintenance.

Indicating light

• Power indicator:
• When the battery power is lower than 3% , the vacuum cleaner automatically enters the shutdown protection state, and the red light flashes to indicate that the power is insufficient. Please charge it in timely fashion.
• When the power adapter is connected and charged, the green light flashes to indicate the charging status. The green light is on when the battery is fully charged, indicating that the charging is complete.
• Fault indicator:
• When the brush sucks in large pieces of rubbish and in other abnormal conditions, the indicator light flashes red.

CLEANING AND MAINTENANCE

Dust cup cleaning

• After turning off the device, press the dust cup release button on the handle, then remove the dust cup to pour out the dust. Reinstall the dust cup and use it again. ( Fig.1)

Disassembly and cleaning

• After the dust cup has been removed, the filter inside can also be removed for cleaning as shown in the picture below. The main engine and filter are aligned with the lock mark and installed, and the filter assembly can be restored by doing the reverse. (Fig.2)

Electric floor brush cleaning

• Turn off the vacuum cleaner, remove the floor brush head by pressing the brush release button and pull the buckle up in the direction of the bottom lock arrow to remove the floor brush. Doing the reverse will restore the floor brush head to its original plac.

• If there is hair entangled on the buckle end of the [ soft velvet roller brush, the buckle can be pulled out for cleaning. The reverse operation will return 1t to its place.

Cleaning the Parts

| HEPA| Unwastable; just tap it lightly
---|---|---
| Dust Cup| Washable; dry before use
| Filter| Washable; dry before use
| Hard Floor Brush| Washable; dry before use

TROUBLESHOOTING

Problems|

Causes

|

Solutions

---|---|---
Vacuum not working|

1. The battery is low.
2. The filter and suction head are blocked.

|

1. Charge before use.
2. Clean the filter and suction head before use.

Suction reduced|

1. The dust cup is full and the filter element is blocked.

|

1. Use after cleaning the dust cup and filter.

Fan not turning| The aluminium alloy tube or transfer pipe is blocked.| Continue to use after removing the matter inside. If the problem is not solved, contact customer service.
Electric brush head not rotating|

1. The electric brush head is blocked by hair.
2. Remove it from unsuitable cleaning place.

|

1. Clean the hair off the electric brush head.
2. Restart/turn off the machine.

STORAGE

Use the matching screws to install the wall mount on the wall. Insert the vacuum cleaner into the cavity of the wall mount. Installation: Take a screw and fix it into the wall. Do not lock the screw head to the bottom, but reserve about 5 mm. Take the wall mount and align the back hole with the screw head to snap it in, then take a screw from the top of the wall mount and lock it. Screws can be used together with expansion sleeves.

WARRANTY: ONE YEAR

PLEASE READ THIS MANUAL CAREFULLY BEFORE USING THE APPLIANCE AND RETAIN IT FOR FUTURE REFERENCE

CUSTOMERS SUPPORT

AIGOSTAR INC
489 Yorbita Rd, City of Industry,
CA 91744(UNIT A)

http://WWW.AIGOSTARUSA.COM
MADE IN P.R.C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>