BROAIMX DC5V Smart Bird Feeder with Camera User Manual

DC5V Smart Bird Feeder with Camera
**User Manual

Customer Support: service@isyoung.com
**

NOTES

1. Keep the bird feeder and all accessories out of reach of children and pets.
2. Make sure the camera has been fully charged .(DC 5V/2A)
3. Working temperature : -5°F to 120°F(-20.5°C to 48.5°C) Working relative humidity: 10%~95%
4. Please do not expose the camera lens to sunlight directly .
5. The camera has an IP65 waterproof rating, which support working properly under rains or snows. But it can not be soaked in water.
6. The bird feeder can only works with 2.4GHz WI-FI.
7. The strong light will interfere the scanning of the QR code while pairing
8. Avoid placing the device behind furniture or near microwaves products.
9. Try to keep the bird feeder within the range of your WI-FI signal.

WHATS IN THE BOX

INTRODICTION FOR BIRD FEEDER

SPECIFICATIONS FOR BIRD FEEDER

SOLAR PANEL SPECIFICATION
IPCE| 19%
Working Voltage (Vmp)| 6V±5%
Working Current (Imp)| 400mA±5%
Open Circuit Voltage (VOC)| 7.2V±5%
Short-Circuit Current (ISC)| 480mA±5%

INTRODUCTION FOR CAMERA

1. Status LED
2. Light sensor
3. Power ON/OFF
4.  Infrared LED
5. Lens
6.  Sync/Reset
7.  Microphone
8. Mounting hole
9. Charging port
10.  Motion sensor Speaker
11. TF card slot (Capacity expansion 128G)

CAMERA SPECIFICATION

INDICATOR STATUS

1. Camera turn on: Red light always ON.
2. Pairing mode: Red light fast blinking.
3. Network connecting: Green light fast blinking.
4. Network connected: Green light always ON.
5. Abnormal status : Red light slow blinking.(Need to reset)
6. During firmware update: Yellow light always ON.
7. Charging status: White light always ON during charging and OFF after fully charged.

HOW TO CONNECT TO THE APP

https://a.smart321.com/combirdlover

Download or scan the QR code and install the Bird Lover App for either IOS or Android. Once downloaded, the APP will prompt you to register your device. Enter your phone number or email address which one makes you feel comfortable and select the country you live in. You will receive the registration code. Input the registration code, then create a password.

1. Turn on the power switch.

2. 0pen the APP and connect according to the following steps.

3. Enter the WIFI password.

4.  Scan the QR code with the camera, and enter the connection after hearing the sound of the camera prompt.
   NOTE : The QR code needs to be aimed at the camera below

5. Wait for the connection to complete, and click “Done’.
   

APP INTERFACE INTRODUCTION

1. Quality adjustment: you can choose HD or SD
2. Battery Remaining Capacit
3. Voice switch
4. Zoom inthe screen for camera
5. Screen horizontal and vertical adjustment
6.  Take photo
7. Bird recognition
8. Shot videos
9.  Playback for previous
10. View photos or videos took
11. Check out the bird collection
12. Share  the device
13. Motion detection(Click to turn on/off)
14. Device Volume
15. One-Way Talk
16.  Siren
17. Notification for motion detection
18. Cloud storage service
19. History for bird recognition
20.  Personal setting

TOP COVER INSTALLATION

1. Align the top cover with the groove of the birdhouse and press down.
2. Connect the battery charging cable to the top cover.
3. Twist and snap the top cover.

HOW TO INSTALL

1. Stick the sticker on the tree or wall and drill holes within the range marked on the sticker.

2. Insert the green plastic screw spacers into the hole.

3. Fix the bracket with long screws.
   

4. Install the bird feeder and align the three holes underneath.

5. Fix bird feeder with three short screws.
   

6. Install the perch with the two screws in the package.

7. The bird house can rotate left and right.
   

HOW TO REMOVE THE CAMERA

Rotate the camera down and unscrew the fixing screw on the back

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>