Xenteq 12V-230V Pure Power Plus User Guide
- June 14, 2024
- XenteQ
Table of Contents
Xenteq 12V-230V Pure Power Plus
Product Information
The product is an inverter that allows users to monitor and control its performance using a mobile app. It is designed to convert DC power from a battery into AC power for various electronic devices.
Specifications
- Input Voltage Range: 15.0V – 16.5V
- Output Voltage: AC 120V
- Maximum Power Output: [insert maximum power output]
- Maximum Load Capacity: [insert maximum load capacity]
- Communication: Bluetooth
Product Usage Instructions
Connecting the Inverter
To connect the inverter to the mobile app, follow these steps:
- Open the app and navigate to the “Devices” page.
- If no inverters are detected, tap on “Scan for devices” to initiate a new search.
- Select the inverter you want to connect with by tapping on its corresponding frame.
- If the app successfully establishes a connection with the inverter, the frame will turn blue.
Dashboard Page
The dashboard page provides real-time information about the inverter’s performance and status. It includes:
- The power being delivered by the inverter on the output.
- Error messages or warnings if any issues are detected during usage. Refer to the inverter’s manual for troubleshooting.
Settings Page
The settings page allows you to customize various values and settings according to your preferences. To make changes:
- Tap on the corresponding blue frame for the setting or value you want to adjust.
- Enter the desired value and tap on “OK”.
- The new setting will be saved in the inverter’s memory.
Adjusting Protection Settings
The inverter offers several protection settings that can be adjusted. Here are the steps to adjust each setting:
Overspanningsbeveiliging (Overvoltage Protection)
- Factory Default: 16.5V (max) / 15.0V (min)
- Tap on the blue frame displaying the current value.
- Enter the desired voltage and tap on “OK”.
- The new setting will be saved in the inverter’s memory.
Onderspanningsbeveiliging (Undervoltage Protection)
- Factory Default: 10.0V (min) / 11.5V (max)
- Tap on the blue frame displaying the current value.
- Enter the desired voltage and tap on “OK”.
- The new setting will be saved in the inverter’s memory.
Onderspanningsalarm (Undervoltage Alarm)
- Factory Default: 10.5V (min) / 12.0V (max)
- Tap on the blue frame displaying the current value.
- Enter the desired voltage and tap on “OK”.
- The new setting will be saved in the inverter’s memory.
Re-start spanning (Restart Voltage)
- Factory Default: 12.6V (min) / 13.5V (max)
- Tap on the blue frame displaying the current value.
- Enter the desired voltage and tap on “OK”.
- The new setting will be saved in the inverter’s memory.
FAQ
Q: Can I change the name of the inverter?
A: Yes, you can change the name of the inverter by tapping on the icon and entering a new name (up to 18 characters). The customized name will be associated with the mobile device used to set it.
Q: How do I troubleshoot errors or warnings?
A: If you encounter an error or warning message on the dashboard page, refer to the inverter’s manual for specific troubleshooting steps.
Q: What is the communication method used by the inverter?
A: The inverter communicates with the mobile app via Bluetooth.
INSTRUCTIONS
- The PurePower App has been specially developed for reading and personalizing the PurePower Plus inverter.
- The app is available for Android and iOS and can be downloaded for free from the Playstore or Apple Store.
- It is important that only the so-called PLUS models from the PurePower series have this option to app control. The PurePower Plus models can also be recognized by the ‘P’ at the end of the article number. These inverters are equipped with a Bluetooth® module. So there is no external dongle or something like that. necessary to establish the connection with the app. The range is approximately 10 meters. The operational
- However, the distance is of course very dependent on the placement of the inverter, any plating and walls or objects etc. located in between.
- After installing the ‘PurePower app’ you can immediately start using it. Make sure the inverter is on stands. Open the ‘PurePower app’ on your mobile device.
Important:
- Give the app permission to use the location if it asks for it the first time you use it.
- Otherwise the app will not be able to detect the inverter.
- Only work via the app and not via the Bluetooth settings of the phone itself.
‘DEVICES’ PAGE
The app opens on the ‘Devices’ page. This page shows all available inverters that are detectable are. If necessary, press ‘scan devices’ below to have the app search again.
Change inverter name
By pressing the icon to the right, it is possible to add your own name to it
relevant device (max. 18 characters). This is possible, especially when using
several devices, a custom ID can be created. The custom ID name is tied to the
mobile device with which the name is given.
Make a connection
Click on the frame of the inverter where you want to contact want to
experience. If the app has contact with the inverter, the frame will color
blue. The app is now connected to the concerning inverter.
‘DASHBOARD’ PAGE
- Real-time information can now be read out on the dashboard page the performance and status:
- The power that the inverter is delivering at the output: in Wattage and in percentage of the maximum power.
- The output voltage (VAC) – The power supplied expressed in amperage The measured input voltage
- The internal temperature
- Notifications If an error message is detected during use, then the relevant error or warning will be displayed here. Consult the inverter manual for troubleshooting.
SETTINGS’ PAGE
On this page you will see the settings and values that you can adjust as desired. By clicking on the relevant blue frame You can always click the value or adjust setting
-
Overvoltage protection
The voltage at which the inverter switches off based on an input voltage that is too high. The factory setting is 16.5 or 33 Volts. This is also the maximum value. The minimum value is 15.0 or 30.0 Volt Click on the blue frame with the current value. Enter the desired voltage and click ‘OK’. The setting made remains in the inverter’s memory. -
Undervoltage protection
The voltage at which the inverter switches off based on an input voltage that is too low. The factory setting is 10.0 or 20.0 Volts. This is also the minimum value. The maximum value is 11.5 or 23.0 Volts. Click on the blue frame with the current value. Enter the desired voltage and click ‘OK’ The setting made remains in the inverter’s memory. -
Undervoltage alarm
The voltage at which the inverter gives the pre-warning signal (buzzer) as an indication of the input voltage threatens to become too low. The factory setting is 10.5 or 21.0 Volts. This is also the minimum value. The maximum value is 12.0 or 24.0 Volts. Click on the blue frame with the current value. Enter the desired voltage and click ‘OK’ The setting made remains in the inverter’s memory. -
Re-start voltage
The voltage at which the inverter automatically restarts after it has failed due to an input voltage that is too low. The factory setting is 12.6 or 25.2 Volts. The minimum value is 12.0 or 24.0 Volts. The maximum value is 13.5 or 27.0 Volts. Click on the blue frame with the current value. Enter the desired voltage and click ‘OK’ The setting made remains in the inverter’s memory. -
Buzzer
The acoustic signal that sounds for pre-warning, undervoltage and overvoltage can be turned on or off to change gear. This is on in the factory setting. Click on the slider to change the position. -
Fan control
At the factory, the fan is controlled based on the power supplied and the internal temperature. This control can be adjusted to either power only or temperature only. The fan may and so it cannot be completely disabled! Please note: adjusting the control affects performance of the inverter and can also negatively affect the life of the internal components. Click on the slider to change the position. -
Standby function
The standby function (sleep mode) can be switched on or off. The sleep mode is disabled at the factory. Click on the slider to change the position. The desired load level for the sleep mode can be adjusted. Click on the blue frame. Feed it Wattage and click ‘OK’. The setting made remains in the inverter’s memory.
LANGUAGE’ PAGE
The language of the app is turned on on this page to fit. The available languages are displayed. Click on the desired language. The relevant frame will light up blue. The choice remains in the app’s memory to stand.
‘PRODUCT SPECIFICATIONS’ PAGE
Overview of the product and app details.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>