Winsen ZP211 Refrigerant Gas Detection Module User Manual
- June 14, 2024
- Winsen
Table of Contents
Winsen ZP211 Refrigerant Gas Detection Module
Product Description
ZP211 refrigerant gas detection module adopts advanced multi-layer thick film manufacturing process semiconductor gas sensor element. The gas sensor element contains a filter adsorption layer to reduce the interference of alcohol and other gases, and has extremely high sensitivity to refrigerant gas R290. The module has been aged , calibration, calibration, with good consistency and high sensitivity.
Features
High sensitivity, fast response, strong anti-interference ability, long life, stable operation, factory calibrated, sensor fault self-diagnosis
Application
Used for air conditioning, refrigeration system refrigerant leak detection.
Parameters
| Model | ZP211 |
|---|---|
| Target Gas | Refrigerant gas R290 |
| Physical interface | S05B-PASK-2 |
| Output Data | PWM |
| Working Voltage | 5.0±0.2V DC (No voltage |
reverse connect protection)
Working Current| ≤80mA
Warm Up Time| ≤3 min
Recovery time| ≤120s
Set alarm
concentration
| 2000ppm
Initial alarm accuracy| 1340～2660ppm
Operating Temperature| -20～55℃
Operating Humidity| ≤95％RH
Storage Temperature| -20～60℃
Storage Humidity| ≤60％RH
Size| 25×34×14.1mm（L×W×H）
Weight| 5g
Terminal definition
| Pin | Name | Function |
|---|---|---|
| G | GND | Input power – |
| R | / | / |
| T | / | / |
O
|
Output
| PWM signal output (need to connect external pull-up resistor)
V| 5V| Input power +
Definition of output signal
| Status | PWM output |
|---|---|
| Preheating | H：75ms |
| Work | H：75ms |
| Alarm | H：225ms |
| Fault | H：300ms |
Note:
- After the module enters the alarm state, it will keep the alarm state and will not switch to other states. It needs to be powered on again to exit the alarm state.
- If the sensor is exposed to high concentrations (above 10000ppm) of R290 gas, the sensor may be damaged and its performance may be affected.
- The module fault signal takes priority over the alarm signal.
Sensor basic testing circuit
The module uses an MP511D sensor, and Figure 3 shows the basic testing circuit
of the MP511D sensor.
The sensor requires two voltages to be applied: heating voltage (VH) and
testing voltage (VC).
Among them, VH is used to provide a specific operating temperature for the sensor, and the voltage is applied to both ends of the heating electrode using a DC power supply. VC is used to measure the circuit’s loop voltage. VRL is the voltage on the load resistor (RL) connected in series with the sensor, which is the output voltage VOUT. The module determines the concentration of refrigerant R290 in the current environment by detecting the voltage of VOUT. On the premise of meeting the electrical characteristics of the sensor, VH and VC can share a common power supply circuit.
Cautions
- Please do not put the module in organic solvent (include silica gel and other cementing compounds), painting, medicament, oils and fuels, high concentration gas etc.
- Please do not impact or vibrate the module seriously.
- Please warm up for 5 min before first use.
- Please do not use the module related with personal safety.
- Please do not install the module in the severe convection environment.
- Please do not put in the module in high concentration organic gas for long time.
- Please supply the module with requested voltage as manual strictly, if voltage is higher than 5.5V, the module will be destroyed irreversibly.
Zhengzhou Winsen Electronics Technology Co., Ltd
Add: No.299, Jinsuo Road, National Hi-Tech Zone, Zhengzhou 450001 China
Tel: +86-371-67169097/67169670
Fax: +86-371-60932988
E-mail: sales@winsensor.com
Website: www.winsen-sensor.com
References
- Winsen Gas Sensor_CO2 Sensor_Air Quality Sensor_Dust Sensor_CO Sensor-Winsen Electronics
- Winsen Gas Sensor_CO2 Sensor_Air Quality Sensor_Dust Sensor_CO Sensor-Winsen Electronics
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>