LANCOM IAP-822 Dual Radio Industrial Access Point Based Installation Guide

: June 14, 2024
: LANCOM

Table of Contents

LANCOM IAP-822 Dual Radio Industrial Access Point Based
Specifications
Installation
Overview
General safety regulations
Power supply
Declarations of conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LANCOM IAP-822 Dual Radio Industrial Access Point Based

Specifications

Hardware

```
* Power supply: DC 12V
```
- Delivery contents: Ethernet cable (3m), 4x 3 dBi dual-band
  dipole antennas, external power supply
Technology:
- WLAN
- SRD / BLE / SRD / ESL (ePaper)
- SRD / SubGHz-ESL
Max. Transmit Power (dBm EIRP):
- WLAN: 20dBm
- SRD / BLE / SRD / ESL (ePaper): 20dBm
- SRD / SubGHz-ESL: 30dBm
- 10dBm
- 14 / 25 mW

Installation

Paul-produyctNeuhaus-836508-Smart-Hom-01

Overview

Overview of the interfaces of the LANCOM IAP-822

WiFi antenna connections
Serial configuration interface
Reset button
ETH1 (PoE), ETH2 interfaces
Power supply connection socket

Establishing the required connections to the device configuration

Always observe the safety regulations and instructions below.
To power the device, select the description a), b) or c) that applies to your current constellation.

Power supply via external power supply
Provide power using the external power supply.

PoE power supply via PoE network device
Connect a network cable to the with PoE marked Ethernet port of the device and a free PoE active Network connection box your local Network (e.g. on a PoE-enabled switch).

PoE power supply via separate PoE injector

Connect a network cable to the one with PoE marked
Ethernet port of the device and the output of the PoE injector. Then connect another network cable with the input of the PoEInjector and a free NON-PoE-active network connection socket your local network. Close
Connect the PoE injector to the power supply

Always pay attention to the documentation for the PoE injector or PoE switch!
Connect other required device interfaces to other components using suitable cables and close For devices with WLAN interfaces, the antennas supplied may be used.
Select one of the following configuration methods a) or b).

Configuration via the local network (recommended)
Please note that an active DHCP server is required on the network connected to the device. Connect the computer intended for configuration (e.g. notebook) either directly using an Ethernet cable the ETH or LAN interfaces of the device or to a switch in the same network. Any existing CONFIG or COM interface is not suitable for configuration via the network!
Configuration via the serial port of a connected computer (if available) You need a serial configuration cable that connects to the CONFIG or COM interface, if available device is connected. This socket is intended exclusively for connection to a serial interface!

Options for initial commissioning of the unconfigured device

Option 1: via a web browser (WEBconfig, not for serially connected devices)
Configuration via a web browser is a simple and quick option as it does not require any additional software must be installed on the computer used for configuration.
Note : If a certificate warning appears in your browser when attempting to connect to your device, there is a button or a link on the browser page displayed to still establish the connection to the device (depending on the browser used, usually under Advanced).
Below, select the description a) or b) that applies to your current constellation to configure thev vdevice.

Configuration in the network without an active DHCP server

The IP address of the device is used for configuration via TCP/IP required in the local network (LAN). After turning on
An unconfigured LANCOM device first checks whether it is in the LAN a DHCP server is active.
The device can be accessed from any computer with activated Auto DHCP Function with a web browser at the IP address 172.23.56.254 can be reached.
The specified IP address can be adjusted at any time.

Configuration in the network with active DHCP server

This procedure requires the one used on your network DNS server is the one reported by the device via DHCP Hostnames can resolve. When using a LANCOM device as DHCP and DNS servers this is by default the case.
You can access your device via https://lancom-XXYYZZ. XXYYZZ are the last six digits of your device’s MAC address. You can find this on the enclosed LANCOM document Management Cloud or on the device nameplate. If necessary, attach your local domain name network ( e.g. B. .internal).
When connecting the computer to an unconfigured LANCOM device, WEBconfig automatically starts the setup process.

Basic Settings Wizard started.

After the setup wizard has been run through, the initial commissioning of the device is complete.
If necessary, make further configurations using the setup wizards available to choose from. → Option 2: via the Windows software LANconfig (www.lancom.de/downloads)
Please wait until the device has finished booting before starting LANconfig.
Open the device configuration by double-clicking on the unconfigured device in the device list.Confirm
Read the security notice and first configure a device password under Management -> Admin -> Device configuration.
Under Wireless LAN -> General -> Logical WLAN settings, configure an SSID and an associated one
Password (PSK). The initial commissioning of the device is now complete. → Option 3: via the LANCOM Management Cloud (LMC)
Special requirements are required to configure the device via the LMC. Information about this You can find the topic at www.lancom.de/lmc-access.

General safety regulations

Under no circumstances should the device housing be opened and the device unauthorized be repaired. Devices, their housings once opened, are excluded from the warranty.
Any existing antennas may only be installed or changed when the device is switched off. The assembly or Dismantling with the power switched on Device can destroy the radio modules.
Explanations of the individual interfaces, switches and displays of your device can be found in the corresponding Hardware quick overview.
Assembly, installation and commissioning may only be carried out by qualified personnel.

Safety instructions and intended use

To safely start up your LANCOM device, please note the following safety instructions: about yourself,
Not to cause damage to third parties or the device. Use the devices only as described in the accompanying instructions documentation described. Observe
In particular, read all warnings and safety-related information.
Use only those from LANCOM Systems recommended or approved third-party devices and components.
Before commissioning, be sure to read the device-specific hardware quick overview. You can find these for download at www.lancom.de/downloads.
Any warranty and liability claims against LANCOM Systems other than those set out below
The intended use described above is excluded!

Vicinity
LANCOM devices may only be operated under the following environmental requirements:

Maintain the temperature and temperatures specified in the quick hardware overview for the corresponding LANCOM device Humidity ranges definitely one.
Do not expose the device to direct sunlight.
Ensure sufficient air circulation and keep the provided ventilation slots free.
The devices must neither be covered nor stacked.
The device must be installed in a freely accessible manner (e.g. without the use of technical aids such as lifting platforms be available); Fixed installation (e.g. under plaster) is not permitted.
Only outdoor devices intended for this purpose may be used outdoors

Power supply

Before commissioning, the following points must be observed, as improper use can result in personal injury and injury

Material damage and the warranty being voided can result:

The power plug of the device must be freely accessible.
Only operate the device with a professionally installed power supply that is nearby and free at all times accessible socket.
Only use the power supply/power supply cable included or listed in the quick hardware overview.
A high contact current is possible for devices with a metal housing and a grounding screw! Connect before connection of the power supply, the grounding screw with suitable ground potential.
Some devices support power supply via an Ethernet cable (Power over Ethernet – PoE). Please note this the corresponding
Notes in the hardware quick overview of the device.
Only use undamaged parts.
Only switch on the device when the housing is closed.
The device must not be installed during thunderstorms and should be disconnected from the power during thunderstorms.
In emergencies (e.g. in the event of damage, penetration of liquids or objects, for example through the ventilation slots), the power supply must be disconnected immediately.

Areas of application

The devices may only be used in accordance with the respective national regulations and taking into account the valid regulations there Legal situation can be used!
The devices may not be used for control, switching or data transmission of machines, their function or their Functional failure can pose a danger to life and limb or is used to operate critical infrastructure become.
The devices with their respective software are not designed, intended or intended for use in the following areas certified: the operation of weapons, weapon systems, nuclear facilities, mass transportation, autonomous vehicles, aircraft, life support computers or equipment (including resuscitation devices and surgical implants), for pollution control, for hazardous materials management or for others dangerous applications where a failure of the device or software could lead to a situation in which it personal injury or death may result. The customer is aware that the use of the devices or the software in such areas of application is entirely at the risk of the customer.

Regulatory information

Regulatory guidelines for devices with radio or WLAN interfaces
As a radio system, this LANCOM device is subject to the regulatory requirements of the legislature. The operator is responsible for operations in accordance with local regulatory requirements, in particular the Compliance with any channel restrictions.

Channel restrictions in WLAN operation for devices with WLAN interfaces
When operating the radio system in EU countries, the frequency range may be 5,150 – 5,350 MHz (WLAN channels 36 – 64) as well the frequency range 5,945 – 6,425 MHz (WLAN channels 1 – 93) only when using the radio system indoors be used. Paul-produyctNeuhaus-836508-Smart-Hom-3

Declarations of conformity

Declarations of conformity for our products can be found on the website www.lancom.de/doc. These include all tested Standards and required guidelines in the area of EMC – SAFETY – RADIO as well as proof of the RoHS & REACH guidelines.

Simplified declaration of conformity
LANCOM Systems GmbH hereby declares | Adenauerstrasse 20/B2 | D-52146 Würselen that this device Directives 2014/30/EU, 2014/35/EU, 2014/53/EU, 2011/65/EU and Regulation (EC) No. 1907/2006 corresponds. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom.de/doc

Documentation / Firmware

Basically current versions are available the LCOS firmware, drivers, tools and Documentation for all LANCOM and AirLancer products for free on our website Website available for download.
A detailed documentation to their You can find the device in the download Portal of LANCOM website: www.lancom.de/downloads
You can also find the LCOS reference manual Explanations for all Functions of your LANCOM device: www.lancom-systems.de/docs/LCOS/Refmanual/EN/

Service & Support

The LANCOM Knowledge Base – with over 2,500 items – you can always find out about them LANCOM website available: www.lancom.de/knowledgebase
If there are any additional questions that remain unanswered please submit your request via our service & support portal: www.lancom.de/service-support
Online support is fundamental at LANCOM for free. Our experts get in touch like this as soon as possible.

All information about your device

LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names and designations used may be trademarks or registered trademarks of their respective owners. This document contains forward-looking statements about products and product features. LANCOM Systems reserves the right to change these at any time without giving reasons. No liability is assumed for technical inaccuracies and/or omissions.