ViaBecs B0CH35L5C9 Wireless Apple Play Car Stereo with Bluetooth Installation Guide
- June 14, 2024
- ViaBecs
Table of Contents
ViaBecs B0CH35L5C9 Wireless Apple Play Car Stereo with Bluetooth
Specifications
- OEM Radio type 1 : This radio is without a factory JBL Amplifier and factory Backup camera.
- OEM Radio type 2: Your car has a factory JBL Amplifier.
- OEM Radio type 3: Your car has a factory JBL Amplifier and factory Backup camera.
Installation Video
Watch the installation video here.
Factory Radio Check:
- Type 1: The XC004-SP harness fits this type of car radio. It can support factory SWC. The car radio comes with an XC004-SP harness.
- Type 2: CAN005-X harness with Simple Soft Canbus fits this type of car radio. It can support factory SWC, factory JBL, and factory backup cameras. You can order it here.
- Type 3: CAN005-X harness with Simple Soft Canbus fits this type of car radio. It can support factory SWC, factory JBL, and factory backup cameras. You can order it here.
Installation Instructions
Step 1: How to remove the factory radio
- Follow the steps shown in the installation video to remove the factory radio.
Step 2: Connect the CAN005-X harness
- Connect the Red AUX R of the power harness with the AUX R IN line of the Audio cable. Connect the White AUX L of the power harness with the AUX L IN line of the Audio cable. Refer to the photo below for visual guidance.
Step 3: Connect the factory backup camera
To connect the factory backup camera, follow these steps:
- Connect the yellow male camera RCA of CAN005-X harness with the PIN10 Rear CAM VIN.
- Refer to the provided photo for reference.
Camera Format Problem:
If your backup camera image is black when you put the car in reverse, please follow these steps:
- Check the resolution of your camera first.
- If your camera is not HD, choose normal – SD – NTSC/PAL.
- If your camera is HD version, choose normal – HD – AHD 720P/25fps or AHD 1080P/25fps.
- Test the camera again after changing the camera format.
Radio Wiring Diagram
To connect an aftermarket backup camera, refer to the wiring diagram provided.
FAQ
Q1: What is the Factory Setting Password?
- The factory setting password is: 123456
Q2: What is the Reset factory?
- The reset factory password is: 7890
Q3: How to change the KPH to MPH?
- To change the speed unit from KPH to MPH, follow these steps:
- Click on the Theme app.
- Go to Setting.
- Click on Plugin.
- Select Speed Unit.
- Change the unit from KPH to MPH.
Q4: How do I update the ViaBecs TS10 software?
To update the system and MCU online, follow these steps:
- Connect your home wifi.
- Open the car setting app.
- Go to About.
- Select Detection Update.
- Click on the check for update key to update to the new version.
Q5: How to activate Tlink for Apple CarPlay & Android Auto?
To activate Tlink, follow these steps:
- Connect to wifi to activate Tlink when using it for the first time.
- To find the wifi, drop down the Quick Setting Menu.
- Long-press the wifi icon to turn it on.
- Click on refresh to get the new QR code.
Installation Video
- STEP 1: How to remove the factory radio. https://www.youtube.com/watch?v=EZpSkmwugAk
Check Your Factory Radio
- OEM Radio type 1: This radio is without a factory JBL Amplifier and factory Backup camera.
- The XC004-SP harness fits this type of car radio. (type 1) It can support factory factory SWC. The car radio comes with an XC004-SP harness.
- OEM Radio type 2: Your car has a factory JBL Amplifier
- OEM Radio type 3: Your car has a factory JBL Amplifier and factory Backup camera.
- 2.3 CAN005-X harness with Simple Soft Canbus fits two types of car radios. (type 2 and type 3). It can support factory SWC, factory JBL, and factory backup cameras.
- You can order it via the link below. https://www.amazon.com/ViaBecs-Harness-Corolla-Highlander-Amplifier/dp/B09SCS9W1S .
How to connect the CAN005-X harness
- STEP 1 : Connect the Red AUX R of the power harness with the AUX R IN line of the Audio cable.
- Connect the White AUX L of the power harness with the AUX L IN line of the Audio cable. You can check the photo below.
- STEP 2: Connect the black Canbus Box
- STEP 3: How to connect the factory backup camera
- You need to connect the yellow male camera RCA of the CAMERA Connector (CAN005-X)with the PIN10 Rear CAM VIN.
- Note: It is a Nissan Wiring harness in the picture. It is as a reference.
Set Camera Format
- Problem: Why my backup camera image is black when I put the car in reverse?
- Please confirm the resolution of your camera first.
- If your camera is not HD, please choose normal — SD — NTSC/PAL.
- if your camera is HD version, please choose the normal — HD — AHD 720P/25fps, or AHD 1080P/25fps.
Then test the camera again after you change the camera format.
Radio Wiring Diagram
- Device Ports
- How to connect aftermarket backup camera.
Set Camera Format
Problem: Why my backup camera image is black when I put the car in reverse?
Please confirm the resolution of your camera first.
- If your camera is not HD, please choose normal — SD — NTSC/PAL.
- if your camera is HD version, please choose the normal — HD — AHD 720P/25fps, or AHD 1080P/25fps.
Then test the camera again after you change the camera format.
TS10 Head Unit FAQs
- Q: What is the Factory Setting Password?
- The password is: 123456
- Q: What is the Reset factory?
- The password is: 7890
- Q: How to change the KPH to MPH?
- Please click Theme app — Setting — Plugin –Speed Unit You can change to KPH to MPH
- Q: How do I update the ViaBecs TS10 software?
- You can update the system and MCU online.
- Please connect your home wifi first and then open the car setting app — about — Detection Update.
- Please click the “check for update” key of the system to update the new version.
- Q: How to activate Tlink for Apple Car Play & Android Auto?
- S1. You need to connect wifi to activate Tlink when you use it at first. How to find the wifi.
- Please drop down the Quick Setting Menu.
- And then a long-press wifi icon to turn on it and then you can try to connect your phone hotspot first.
- Note: Please clear the Tlink usage record first.
- S2: you can change the Time Zone manually.
- Please car setting app — Android Setting — go to settings> system > date & time. you can turn off the option of “Automatic Time Zone” first.
- Then change the time zone manually.
- one person shared a YouTube video on how to activate Zlink successfully via this solution https://www.youtube.com/watch?v=2mjZIYWJMkw
- S3. If Tlink still asks you to put the auth_key, please take a clear photo of the QR activating code and then send me, and then my engineer will activate it after scanning the code.
- Please click “About” on the Tlink app
- Choose the first option (Wireless Carplay + wired Carplay + Android Auto) Then click the “refresh” to get the new QR code
- Take a photo and send it to me
Note: the code will be invalid if the time is too long and then our engineer will scan the QR code to activate it.