hyco RAD15Y Oil Filled Radiator Instruction Manual

: June 14, 2024
: hyco

Table of Contents

Important safety points
Installation
Operation
Timer operation (RAD20TY)
Maintenance
Specifications
Guarantee and service policy
Read User Manual Online (PDF format)
Download This Manual (PDF format)

hyco RAD15Y Oil Filled Radiator Instruction Manual

Important safety points

Do not carry the appliance by the supply cord.
Do not let the supply cord hang over the appliance.
The supply cord cannot be replaced by the user. If the cord is damaged the appliance should be returned to the manufacturer or an authorised service agent for replacement.
Do not cover the appliance as it may cause overheating.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
This unit should be installed at least 1.5m from baths, showers, laundries, swimming pools etc.
Some parts of this product can become very hot and cause burns. Particular attention should be paid where children and vulnerable people are present.
This heateris illed with a precise quantity of special oil. Repairs requiing opening of the ail container are\ only to be made by the manufacturer or their service agent.
Always ensure the castors are mounted to the bottom of the heater.
DO NOT TURN ON THE HEATER IF IT IS UPSIDE DOWN
Always switch off the appliance when notin use.

Installation

Always ensure the castors are mounted to the bottom of the heater. DO NOT TURN ON THE HEATER IF IT IS UPSIDE DOWN

Remove all the packaging.
Turn the heater upside down.
Position the wheel mounting plates between the end two fins at both ends of the heater, attach them using the U-bolt and wing nuts provided.
Attach the castors to the plates using the nuts provided.
Ensure all nuts are tightened and then return the heater to the correct way up.
Allow the oil to return to the bottom of the unit before turning on, around two minutes should be sufficient.

Operation

It is normal for there to be some smells and fumes on the first operation or after along period of not being used, this will disappear within a short period of use.

Basic operation

Choose a suitable location for the heater, ensure all the points in the safety section of these instructions have been followed.
High
Insert the plug into a suitable socket.
Turn the thermostat knob (A) clockwise to its maximum setting.
Select a power setting from the four available ON settings (B).

0 = OFF 1 = Low (600/800W) Medium (900/1200W) III=High (1500/2000W
Once the room temperature has reached the desired temperature adjust the thermostat setting down (anti-clockwise) until a click is heard and the element indicator light (C) goes out. This will now maintain your current room temperature
To turn the heater off simply return the power selection knob to the 0 (OFF) position.

Timer operation (RAD20TY)

To use the 24hr timer you should select the operating mode by sliding the switch in the center of the timer disk as follows:
I’= Onatalltimes
= Timed operation 0
O= Offatall times

(In all modes the times will continue to keep time whilst connected to the mains power supply).
To create your own schedule you should move the slider to the position.
To set the time on the timer simply turn the outer timer disc until the arrow on the centre timer disc points to the current time (24hr format).
The timer has a total of 24hrs marked on the outer disc and these are broken down further by four individual segments that represent 15min intervals within that hour. Push the desired segments out, away from the centre timer disc to confirm you would like the heater to be on at the corresponding time. Repeat this for each 15min interval the heater is required to operate.
To change the time to be off, push the segments in towards the centre timer disc at the required intervals.

Maintenance

Always isolate the appliance from the power supply before commencing any maintenance and ensure the unit has completely cooled.
Never use abrasive chemicals or materials to clean the unit.
Clean the exterior of the unit using a soft, dry cloth.

Specifications

RAD15Y	RAD20TY
Voltage	230v~50Hz
Power	1.5kW
Height (mm)*	Width(mm)
---	---
RAD20TY	690
RAD15Y	690

Depth excluding feet, depth including feet 240mm.
Dimension

Model identifier(s) : RAD15Y

Item	Symbol	Value	Unit	Item	Unit
Heat output	**Type of heal Input. for electric storage local space

heaters only (select one)
Nominal heat output| Pnom| 0,7612| E| manual heal charge control, with integrated thermostat| 2
Minimum heat output (indicative)| Pmin| 0,4217| E| manual heat charge control with room and/or outdoor temperature feedback| 2
Maximum continuous heat output| Pmax, c| 0.7612| E| electronic heat charge Dankol with loom and/ or outdoor temporal= feedback| 2
Auxiliary elactrially oonumptbn| | | | fan assisted heat output| 2
At nominal heat output| elmax| NA| E| Type of heal output/room temperature control (select one)
At minimum heat output| elmin| NA| E| single stage heat output and no room temperature control| No
In standby mode| el51:1| NA| E| Two or more manual stages. no room temperature control| No
| | | | with mechanic thermostat room temperature control| Yes
| | | | with electronic room temperature control| No
| | | | electronic room temperature control plus day timer| No
| | | | electronic room temperature control plus week limey| 2
| | | | Other control options (multiple selections potable)
| | | | room temperature control. with presence detection| No
| | | | –im temperature control. with open window Getection| £
| | | | with distance control option| No
| | | | with adaptive start control| No
| | | | with working time limitation| No
| | | | with black bulb sensor| No
Contact details| Produced for Hyoo Manufacturing Ltd. Normandy Court, Express Way, Castleford, WF10 5NR.|
Model identifier(s):** RAD2OTY

Guarantee and service policy

This product is guaranteed against faulty materials and manufacture for a period of one year from the date of purchase. Hyco will in its sole discretion replace, repair or refund any faulty unit. Incorrect installation and failure to follow correct operating instructions are excluded. Consequential costs such as labour charges or damage to surroundings are expressly excluded

INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE EUROPEAN DIRECTIVE 2012/19/EU.

At the end of its working life this equipment must not be disposed of as household waste. It must be taken to a local authority waste collection centre or to a dealer providing this service. Disposing of electrical and electronic equipment separately enables its components to be recovered and recycled to obtain significant savings in energy and resources. In order to underline the duty to dispose of this equipment separately, the product is marked with a crossed out dustbin.

Hyco Manufacturing Ltd
Normandy Court
Express Way
Castleford, WF10 5NR

T 01924 225 200
F 01924 225 210
E sales@hyco.co.uk