HYCO W28LD Series 2D Ring Scanner User Manual

HYCO W28LD Series 2D Ring Scanner

Design

Ring Scanner

• Wearing: wear on the index finger on the left or right hand
• Scanning: touch either side of the ring body with the thumb finger to trigger the scanning

Ring scanner charging cradle（Bluetooth Receiver）

Charging

Charging Ring Scanner

• Connect the Ring scanner charging cradle to power, and click the ring scanner into the bottom of the cradle with the scan window upward. Please note the power contacts of the ring and cradle must be touched.
• The red light indicates it is in charging, when the green light turns on, it’s finished charging.

Warning: don’t look straightly into the scan window when scanning in case of harm to your eyes.

Take the Ring Scanner out of the Ring scanner charging

cradle

• Hold the middle of the ring scanner gently and pull out upward from the cradle.

Ring Scanner Modes

SPP Mode (default factory settings)
Charging cradle connection and program docking mode

COMMON

To connect with PC via USB cradle, scan COMMON code, and scanning barcode is available. (Random terminal system is acceptable with the cradle) In this protocol transmission mode, if you need different system program docking, please get the relevant development SDK at the official website or contact the relevant agent technical support.

HID Mode

• Use the terminal device directly. Output barcodes in HID keyboard mode searched by default Bluetooth. According to the actual system, scan the barcode corresponding to the system and connect.

IOS

• If the device is connected to IOS smartphone/tablet, scan the IOS code to read the barcodes.

ANDROID

• If the device is connected to an ANDROID smartphone/tablet, scan the ANDROID code to read the barcodes.

WINDOWS

• If the device is connected to WINDOWS smartphone/tablet, scan the WINDOWS code to read the barcodes.

Bluetooth connection

Connect with PC

Connect the cradle with the PC with USB, and the green light means a normal connection. After 15 seconds, scan the Bluetooth connection barcode with the ring scanner, and a blue light indicates a successful connection.

Connect with an Android smartphone/tablet

First, find the Bluetooth connection barcode on the side of the cradle, scan it with the ring scanner, and change the Bluetooth name to the serial number so that the device can be found; Then open ‘Bluetooth Search’ at the setting menu, find the Bluetooth serial number in the list and connect. A green light indicates a successful connection.

Components

Specifications

scanning once every 5 seconds)
Scanning Trigger| Touch-to-scan
IP Level| IP66
Drop Test| 3 meters
Operating Temperature| -10℃ to 50℃ (14℉ to 122℉)
Humidity| 0%-95%RH (non-condensing)

Note: For Ring Scanner and Ring scanner charging cradle, operating temperature is -10°C to 50°C

Functions

Scanning

• Wear on the left or right index finger, touch the left or right side of the ring and aim at the barcode, the ring light turns green, it starts to scan.

Ring Straps

• Firstly, straightly pull out the ring strap from the slot, then choose another ring strap and push it to the top of the slot.

Ring Indicator

• The green light indicates successful scanning.
• The red light flashing indicates a low battery.
• The green light keeping on for 1 second indicates a successful Bluetooth connection.
• The blue light keeping on for 1 second indicates Bluetooth disconnection.
• The red, green, and blue light flashing indicates restarting.

Bluetooth can’t connect

• Normally, if the Bluetooth light doesn’t turn on, the user can scan the barcode “Reset Bluetooth Name”, wait for 10 seconds, and reconnect.

Reset Bluetooth Name

Restore factory settings

• Scan the barcode “Restore factory settings”, the ring will disconnect the Bluetooth connection with terminal devices, and all the settings will change to factory default.

Charging cradle light indicator

• The blue light indicates a successful Bluetooth connection between the ring scanner and cradle.
• The red light is off while the green light on in charging indicates fully charged.

Wake up the ring in charging

• The ring doesn’t work when in charging, while it could be waked up by touching either side of the ring three times.

Laser calibration

• If laser length changes longer or shorter, please stop scanning, touch ring for 4 seconds once, and repeat several times to get it right. If it’s still abnormal, please scan the barcode “Automatic calibration”

Restore factory settings

• After scanning the barcode “Automatic laser calibration”, the ring turns on purple, put it on the table, and wait for 15 seconds until the purple light turns off. The ring laser is calibrated right and functions normally.

Code system on/off

1. Basic setting. 4 default code systems on: EAN13, EAN128, CODE128, CODE39; in which CODE128 and CODE39 read at least 2 characters;
2. Extended setting. 9 default code systems on: EAN8, EAN13, EAN128, UPCA, UPCE, CODE128, CODE39,CODE93, ITF25; in which CODE128 reads at least 1 character; ITF25 only reads 14 characters as default.

Default Basic Setting Default Extended Setting

If a code system and code length are not included please contact technical support and local distributor

Touch switches on both sides
The touch switch on the left and right sides of the ring scanner are both on by default. If you need to turn off one side, please use the following barcodes to turn it on/off.

• Left Touch Key On
• Right Touch Key
• On Both Sides Touch Keys On

Service

• *  **Warranty:** one year for ring scanner, half-year for battery and accessories.

Notice

• The ring window must be kept clean. Improper usage will breach the limited warranty clause.
• Avoid rough objects scratching the window.
• Remove stains from the window by soft cloth.
• Do not spray any liquid onto the window.
• Use cleaning water to clean.

Function barcodes setup

• Change function of scanning after scanning the following barcodes:

Device information

• “Device information” barcode includes device information (e.g. serial number, version number, Bluetooth version information).

Vibration open

Vibration close

• Scan function code “Vibration Open” to activate vibration function,
• Scan function code “Vibration close” to close vibration function,

Slow down data transmission through the ring cradle

Speed up data transmission through ring cradle

• In HID mode, scan the barcode “Speed up data transmission through ring cradle”, it can accelerate the data transmission speed between the cradle and computer; scan the barcode “Slow down data transmission through ring cradle”, it can slow down the data transmission between the cradle and computer.

Triggered continuous scanning

• Scan the barcode “Triggered continuous scanning”, the ring could keep scanning when the user keeps touching the ring. If the user wants to change to common scanning, scan the “Manual Trigger Mode” bar code.

Manual Trigger Scanning

• “Manual Trigger Mode” is set by default, the user needs to touch the ring once to scan once.

Automatic Interval Scanning

• After scan the “Automatic interval scanning” bar code, the ring could automatically scan every 0.5 ~ 3 seconds without touching (2 seconds by default)

Automatic interval scanning-reduce

• After scanning the “Automatic interval scanning-reduce” barcode, it can expedite the scanning speed once by 0.5 seconds, the fastest scanning speed is scanning once every 0.5 seconds.

Automatic interval scanning-increase

• After scanning the “Automatic interval scanning-increase” barcode, it can slow down the scanning speed once by 0.5 seconds, the slowest scanning speed is scanning once every 3 seconds.

Scan angle adjustment
According to different barcode lengths, the user needs to change laser length to achieve a better scanning effect.

1. Scan the “Laser calibration” barcode to activate the function, the ring light turns white and begins to automatically and intermittently scan.

Laser calibration

1. After scanning the “Widen” barcode, the laser length becomes long; after scan the “short ” barcode, the scan angle becomes short.

Extend laser Shorten laser

Note: do not extend or shorten more than 10 times one time.

1. Scan the “Confirm” barcode, the ring light turns yellow and white, the laser length is confirmed.

Laser confirm

1. Scan the “Data generation” barcode, the ring light turns yellow and red, and then turns purple for a while. The laser length is set successfully after the purple light turns off.

Data generation

Common functional barcodes

To meet the different needs for customers, there are some functional barcodes used to meet the requirements for different customers.

Add Enter

Delete Enter

After scanning the “Add Enter” barcode, it can automatically move to the next line in the text field after each scanning. If user wants to close the function, scan the “Delete Enter” barcode. After scanning “Add the tab” barcode, it can automatically move to next line in excel after each scanning. If user wants to close the function, scan the “Delete the tab” barcode.

Add TAB

Delete TAB

SYCO Technology

• Website: www.hycoiot.com
• Email: global_sales@hycoiot.com
• Phone Number: +86 15201965826

References

• Ultra-low power consumption Ring scanners, Wireless Light Tag, Wearable Computor, wearable IoT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>