HDMI E25 Mini Portable Upright Projector Instruction Manual

HDMI E25 Mini Portable Upright Projector

Product Information

Specifications

• Model: [Model]
• Lamp: [Lamp]
• Image System: [Image System]
• Language: [Language]
• Input Voltage: [Input Voltage]
• Weight: [Weight]
• Working Temp: [Working Temp]
• Input Port : [Input Port]
• Output Port: [Output Port]
• Aspect Ratio: [Aspect Ratio]
• Size: [Size]
• Operation Mode: [Operation Mode]

Projector Knowledge

The projector can input high-definition video signal and composite video signal, and supports stereo audio signal input and output. Please refer to the following figure to connect the projector and other audio equipment according to your own needs.

Projector Installation

Standard Setting
Please refer to the following table to adjust your picture size and distance (from the lens to the screen):

Installation Method
Contact a professional installer to mount this projector to a ceiling. Follow the instructions below for the correct projector positions:

• Front projection ceiling mount: [Installation Steps]
• Rear projection ceiling mount: [Installation Steps]
• Front projection table mount: [Installation Steps]
• Rear projection table mount: [Installation Steps]

Turn the Projector Operation On/Off
When the projector is connected to a power source, the projector enters standby and the cover signal indicator is red.

• Operation on: Press the power key on the body or the power key on the remote control, the indicator will turn blue and enter the working state.
• Operation off: In the working state, press the power key of the body or the power key on the remote control, the indicator changes from blue to red, and the projector is turned off.

FAQ

• Q: Does this model support Dolby audio decoding?
  A: No, this model does not support any Dolby audio decoding due to the copyright of Dolby patent.

Please read the manual carefully before operating projector..

Important Safeguards

Installation

• To get a better watching, please use this projector while drawing the curtain or in a dark room.
• Please use the projector carefully, dropping or crashing may damage parts or result in blurred images and abnormal displaying.

Power

• Be careful while using the power cord, avoid excessive bending; the damage of power cable may cause electric shock and fire.
• It is better to unplug the power cord after power off.

Cleaning

• Unplug the power cable firstly.
• Clean the shell regularly with a damp cloth, neutral detergent can be used.
• Please use a glasses cloth or lens paper, not to scratch the lens.
• Please clean projector’s vents and speakers regularly by banister brush, or the ventilation will be blocked.

High Temperature Attention

• While projection or just finishing, the exhaust port nearby will be very hot, if touch it, would get scald.
• While projection, please do not look the lens directly, or may hurt eyes.

*Warm Tips

• Do not disassemble the projector, if not, there will be a risk of electric shock, and the disassembling affect the normal warranty.
• Please do not put any liquid or heavy stuff on the projector.
• To ensure the stability of heat dissipation, please open the height bracket in the bottom of the projector before starting.

Accessories List

• Remote Control ×1
• Power Cable ×1
• User Manual ×1

Projector Knowledge

Projector can input high-definition video signal and composite video signal, and support stereo audio signal input and output. Please refer to the following figure to connect the projector and other audio equipment according to your own needs.

1. Carrying Handle
2. Lens
3. Camera(Only available in auto focus version)
4. IR Receiver
5. USB port
6. 3.5mm port for Audio Output
7. AV port
8. HDMI port
9. IR Receiver
10. Speaker
11. Cooling Window
12. Power Socket

Projector Knowledge

1. Power Key
2. Rating Label
3. Bracket Holes (1/4 inch nut*1, depth 6mm),Supports Hoisting

Specifications

Multimedia Format Supported

This model does not support any Dolby audio decoding due to the copyright of Dolby patent.

Remote Control

1. Signal Indicator
2. Power Key
3. Arrow keys
4. Home Key
5. Return key
6. Volume+
7. Volume-
8. Source key
9. Confirmation key
10. Menu
11. Mute Key
12. Focus+
13. Focus-
14. Screen Flip

Projector Installation

Standard Setting
Please refer to the following table to adjust your picture size and distance. (from the lens to the screen).

Please allow ± 3% to the image sizes in the table above. If the distance is less than min data and more than max data, the image could be blurry.

Warning: Please check the diagram below for the trapezoid adjustment.

Installation Method
Contact a professional installer to mount this projector to a ceiling. Follow the instructions below for the correct projector positions. Warning:

1. The projector may be damaged beyond repair if it is incorrectly mounted on a ceiling or on a surface.
2. The projector should only be used in an environment where the temperature does not exceed the range of 5 ℃-35℃. Projector malfunction may occur if this is not adhered to.
3. Malfunction may occur if the projector is subjected to dusty, wet, moist or smoky conditions.
4. Poor ventilation could cause overheating which could lead to damage to the projector as well as a life threatening situation.

Turn the Projector Operation On/Off

• When the projector is connected to a power source, the projector enters standby and the cover signal indicator is red.
• Operation on: Press the power key on the body or the power key on the remote control, the indicator will turn blue and enter the working state.
• Operation off: In the working state, press the power key of the body or the power  key on the remote control, the indicator changes from blue to red, and the projector is turned off.

Use of the Projector

• Image focusing
  When the newly installed projector is used for the first time, the image will be blurred, and it is necessary to focus the picture；

• Manual Focus
  When the picture is blurred, press the focus keys “F+” and” F- “on the remote control to adjust the focal length of the lens. Tap or long press the focus button until the picture is clear. (As shown below) Or press the menu button on the remote control; select “Settings” → Keystone → Projection Settings → Manual Keystore.

How to Use Projection Settings

• Select the settings icon in the upper right corner of the main interface, and then press the “OK” key on the remote control to enter the settings interface and select “Projection Image

• Setting”.  After entering the interface, select the mode you want in the projection settings.

• Projection mode: Front-Desktop / Rear-Desktop / Front-Ceiling / Rear-Ceiling

• Automatic Keystore (Enable this function, when the device displacement can also keep the picture square )

  • Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

• Manual Keystore (Manually adjust the four corners through the arrow keys until the screen can be corrected )

• Automatic Focus (This function is turned on by default, and the screen can be kept square even after the device is displaced. )

  • Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

Digital Zoom (Zoom out or enlarge the image )

Correction Settings

• Trapezoidal Correction Reset: Restores the screen to its original proportions
• AutoKeystone Correction At Power On: It can automatically adjust the square of the screen after booting
• Power On Auto Focus: It can automatically adjust the picture to be clear after booting
  • Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

How to Select the Source
Select the source channel you want to enter in the list on the left side of the main interface, such as HDMI 1 / HDMI 2 / AV, then press the “OK” key on the remote control to enter the corresponding source interface.

How to Connect to WiFi

• Select the settings icon in the upper right corner of the main interface, press the “OK” key on the remote control to enter the settings interface, and select “WiFi Setting”.
• After entering the interface, select the WiFi you want to connect to in the list below, then enter the password and complete the connection. Connected will be displayed behind the successfully connected WiFi.
• Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.
• Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

How to Connect Bluetooth

• Select the setting icon in the upper right corner of the main interface, press the “OK” key on the remote control to enter the setting interface, and then select “Bluetooth Setting”.
• After entering the interface, turn on Bluetooth, search for Bluetooth, and pair Bluetooth.
• Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

How to Use iOS Cast
In the main interface, select “iOS Cast”, press the “OK” key on the remote control to enter the interface, and and then set up in the order in the interface.
Note: The projector needs to be connected to the Internet for using the iOS Cast or upgrading the projector for the first time

1. The iOS device and the projector are connected to the same network
2. Open the control center of the iOS device and select Screen mirroring
3. Choose the corresponding projecton device name.

Make sure that your iOS device is connected to the same network as your Projector.

1. On your iOS device, open Control Center and tap screen  Mirroring.
2. Looking for devices that can be mirrored on.
3. Select BirdCast-XXXX from the list.

Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

How to Use Miracast
Select “Miracast” in the main interface and press the “OK” key on the remote control to enter the interface, and then set up in the order in the interface.

1. Turn on the WIFI of the Android device. (It is recommended that the projector is connected to the same router or the WIFI of the Android device is not connected to any router) ·
2. Turn on the “Wireless Display” of the Android device.
3. Select the corresponding projector device name.

Miracast
To connect Android mobile/Pad with Projector Based on WiFi-Display Technology

1. On your Android device, turn on WLAN (not necessary to connect to any Wi-Fi router)
2. Launch the Multi-screen/ Wireless Display / Screen Mirroring / Smart View function
3. Select Please waiting from the searching result list

Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

How to Play Files in USB Disk

• Select the required category “movie”, “music”, “photo” or “Office Suite” in the main interface, and press the “OK” key on the remote control to enter the corresponding category.
• Then find the file you want to play in that category, start playing by pressing “OK” key. (You cannot enter the required category without connecting a USB disk.)
• Note: As the product system is updated from time to time, the specific operation content is based on the actual situation.

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
NOTE:

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

“This device complies with part 15 of the FCC Rules.  Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.”

“In order to comply with FCC RF Exposure requirements, this device must be installed to provide at least 20 cm separation from the human body at all times.  “This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence- exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.”

This is only required if product is within ICES- but not both, to identify the applicable Class of the device used for compliance verification. “CAN ICES-3 ()/NMB-3()”

HIGH- DEFINITION MUTI MEDIA INTERFACE
The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI Trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>