ErGear EGESD5B-3 48 Electric Standing Desk With A Build In Drawer Instruction Manual

ErGear EGESD5B-3 48 Electric Standing Desk With A Build In Drawer

Specifications

Height Adjustment Range 28.3″-46.5″ (72-118cm)

• Power Input
  100V-240V

• Max. Speed
  20mm/s

• Operating Noise
  <55dB

• Max. Load
  176 lbs / 80kg

Step 1: Supplied Parts and Hardware

• Crossbar
  

• Left Desk Leg
  

• Right Desk Leg
  

• Leg Base
  

• Bolt

• Bolt

• Large Allen Wrench 3/16″ (5mm)

Step2: Supplied Parts and Hardware

• Side Plate
  

• Transmission Rod
  

• Bolt

• Small Allen Wrench 5/64″ (2mm)

• Large Allen Wrench 3/16″ (5mm)

• Rubber Pad

Step 3: Supplied Parts and Hardware

• Desktop
  

• Screw
  

• Wood Dowel Pin

• Headset Hook
  

• Desktop Panel Connector
  

• Left Drawer Side Plate
  

• Right Drawer Side Plate
  

• Controller
  

Step 4: Supplied Parts and Hardware

• AC Adapter
  

• Cable Clip

Step 5: Supplied Parts and Hardware

• Fabric Drawer

• Drawer Bottom Board

• Drawer Knob

• Bolt
  

Step 1 Assembling and Connecting the Desk Legs

Step2 Attaching the Side Plates and the Transmission Rod

Loosen the coupling nut.

Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to lower the left leg or anti-clockwise to raise it.

Ensure the transmission rod is properly inserted into the hole in the left leg. Smoothly connect the other end of the rod to the end of the motor drive shaft on the right leg.

Secure the transmission rod to the motor drive shaft by turning the set screw clockwise.

Step3 Assembling and Attaching the Desktop

Assemble the desktop.

Attach the desktop to the frame.

Attach the hooks, controller, and drawer side plates to the desktop.

Step 4 Connecting the Cables

Step 5 Assembling the Drawer

Step 6 Inserting the Drawer

Using the Controller

• Save Current Height Setting
  Short-press the button, and the display will flash. Press the 1 2, or 3 button to save the current height setting to that button.

• Select Height Setting 1
  Press the 1 button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 2
  Press the 2 button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 3

• Press the 3 button, and the desk will move to the height that was previously set for that button.

• Raise the Desk
  Press the button to raise the desk continuously until it reaches them highest position of 46.5″ (118cm) or the button is released.

• Lower the Desk
  Press the button to lower the desk continuously until it reaches the lowest position of 28.3″ (72cm) or the button is released.
  

Settings

Change Display
Height Units

| Press and hold the button until a flashing ‘S-‘ is displayed.
Press again, and ‘Un’ is displayed. Press to select it, press or to switch between ‘IN’ (imperial) and ‘SI’ (metric), and press to save your choice.

Change Collision
Detection Sensitivity

| Press and hold the  button until a flashing ‘S-‘ is displayed.
Press again, and ‘Un’ is displayed. Press or to switch to ‘CF’ and press to select it. Press or to switch between off, low, normal, and high sensitivity. Press 00 to save your choice.

Reset

| Press and hold the button for 5 seconds, and the screen will show ‘RES.’ Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Hot

| Overheating Protection: When the motor has been working continuously for 2 minutes, it will stop operating to prevent damage from overheating. Wait for at least 18 minutes before making any further height adjustment.

ElO

| Sensor Malfunction Warning: Motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.

E20

| Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.

E02

| Operation Status Warning: The desk stops moving if vibration, impact, or incline are detected. If this detection is incorrect, follow the reset instructions before continuing use.

E32

| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
---|---

E31

| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.

E60

| Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions.
Power on again.

–

| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

Technical Support

(us/CA) l-800-651-9525 Mon-Fri, 8am-8pm ( CST)
(UK) 44-808-196-3875 Mon-Fri, 2pm-10pm (UTC)
Other Info
support@ergear.com

Website
https://ergear.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>