MOUNTUP MU0002 Dual Monitor Desk Mount Instruction Manual

June 14, 2024
MOUNTUP

MOUNTUP MU0002 Dual Monitor Desk Mount Instruction Manual
MOUNTUP MU0002 Dual Monitor Desk Mount

Must Check Before Installation

  1. Is your monitor VESA 75×75mm/3×3″ or 100×100mm/4×4″?
    Installation

  2. Is the weight of your monitor (including accesso ries) less than 19.8 lbs (9kg) each arm?

  3. Is your desk thickness 10~50mm (0.39~1.97”)
    Installation

If this mount is NOT compatible, please contact our customer service to nd a compatible mount.

WARNING!

Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly speciated in this manual. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

Supplied Parts List

  • a (x1) Pole
    Supplied Parts List

  • b (x1) Swivel Arm
    Supplied Parts List

  • c (x2) VESA Plate

  • d (x1) Clamp

All are included in d
All are included in d

  • A (x2) Nut M6

  • B (x2) Bolt M6mm

  • C (x8) Bolt M4×30mm
    Supplied Parts List

  • D (x8) Bolt M4×12mm

  • E (x8) Spacer L10mm

  • F1 (x1) Wire Clip

  • F2 (x4) Wire Clip

  • G (x1) 6mm Allen Key

  • G (x1) 5mm Allen Key

  • G (x1) 3mm Allen Key

NOTE: Not all hardware included will be used.

ASSEMBLY STEPS

Warm Tips

You could also refer to the Video Guide about installation on our product page.

STEP 1: Apply Pad to the Pole Bottom

Apply pad (e) to the Pole (a) bottom to avoid desk scratches
Installation

STEP 2: Clamp Installation OR Grommet Base Installation

OPTION A: Clamp Installation

  1. Mount Clamp (d) to the bottom of Pole (a) by tightening bolts (B) with 5mm Allen Key (G).
  2. Adjust the Clamp width to t your desk. Secure stand to the desktop by tightening Clamp (d).
    Installation

STEP 2: (Continued)

OPTION B: Grommet Base Installation

  1. If existing grommet hole comes with a plastic protector, remove it to ensure a at surface before installing the desk mount.
  2. Detach Bracket (d1) and Bolt Y (d2) from Clamp (d).Installation
  3. Position pole (a) on the mounting surface and then secure it by tightening the plastic knob after making Bolt Y (d2) through the Bracket (d1), desk hole, and the bottom of Pole (a) sequentially.
  4. Installation

STEP 2: Install Arm to the Pole

  1. Install Wire Clip (F1) and Swivel Arm (b) to the Pole (a).
    Installation

  2. Fasten the bolt with supplied Allen Key (G 6mm).

  3.  Attach the Wire Clip (F2) to the Swivel Arm (b).
    Installation

STEP 3: Attach the VESA Plate to the Monitor

OPTION A: Flat Back Monitor

Attach the VESA plate (c) to the monitor with M4×12 bolts (D).

NOTE: Hand tighten screws to avoid over tightening.
Installation

OPTION B: Curved or Recessed Back Monitor

Attach the VESA plate (c) to the monitor with M4×30 bolts (C) and M4 spacers (E).

NOTE: Hand tighten screws to avoid over tightening.
Installation

STEP 4: Slide the Monitor onto the Head of Swivel Arm

Slide the monitor onto the head of Swivel Arm (b) as shown in diagram.
Installation

Install the security Nut (A). Make sure the security nut is installed before you rotate the monitor.
Installation

STEP 5: Make the Necessary Adjustments

Fix the tilt angle

Tighten the bolt with the supplied Allen Key (G 5mm) to x the tilt angle.
Installation

Fix the swivel angle

Use the supplied Allen Key (G 5mm) to make the necessary adjustments. Ignore this step if the arm joint has screwed to the proper tightness.
Installation

STEP 6: Adjust the Level of Monitor and Manage the Wires

For minor height adjustment, remove the Nut (A) and turn the bolt with the supplied Allen key (G 3mm) to raise or lower the monitor. Install the Nut(A) after the adjustment.
Installation

Manage the wires and store the Allen keys (G 6mm, G 5mm, G 3mm) in Wire Clip (F1) for future use.
Installation

Product Dimensions

Installation

CAUTION AND MAINTENANCE:

  • Never allow children to climb, stand, hang, or play on any part of monitor or stand.
  • This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
  • Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals